SW-MOTECH BC.HTA.07.740.30600 Side Saddlebags Instruction Manual
- June 3, 2024
- SW-MOTECH
Table of Contents
BC.HTA.07.740.30600 Side Saddlebags
Instruction Manual
HTA.07.740.80600/B
BC.HTA.00.740.31000
MOUNTING INSTRUCTIONS
Revision:00 – Datum / Date: 01 – 2018
BLAZE® H panniers set
Thank you for choosing this quality product from SW-MOTECH.
Please visit our webshop for additional information, such as application
charts and PDF mounting instructions. Any other documents that may be required
(e.g. ABE certifications), are also available for download at our webshop.
www.sw-motech.com
Installation and/or maintenance of this product requires good technical understanding. For your own safety SW-MOTECH recommends having installation and/or servicing carried out by a specialist workshop.
SW-MOTECH assumes no Liability for damage caused by improper installation and/or maintenance work.
Carefully follow all the directions given in the mounting instructions. Also pay attention to all relevant information in the vehicle manual during assembly. Nonconformance can lead to vehicle damage or even endanger the driver! Please keep the mounting instructions as reference.
This product was developed for vehicles in their original condition.
Compatibility with original accessory parts or other manufacturers’ accessory parts is not guaranteed. Installed accessories can change the driving behaviour and/or stability of your vehicle.
GENERAL INFORMATION
Please observe any country-specific regulations concerning vehicle
registration or operation as well as TUV regulations where applicable. If
required, register installed parts in the vehicle documents together with the
appropriate inspection authority.
PREPARATION: Read the mounting instructions carefully and make sure that all
parts are included. Make sure that your vehicle is parked safely and cannot
fall over. Turn off the engine and remove the ignition key. Let the
motor/exhaust cool off if necessary. Disconnect the vehicle battery when
working on the electrical system. Make sure to use only the appropriate
tools. During installation have another person help you.
MOUNTING: All parts and connections removed from the vehicle must be
reinstalled in accordance with the vehicle manufacturer specifications or
replaced by parts and hardware delivered by SW-MOTECH. Secure all threads,
unless otherwise specified, with medium-strong strength liquid thread locker.
If not otherwise defined by the vehicle manufacturer or SW-MOTECH, screws and
nuts must be tightened according to DIN/ISO specifications. After installation
make sure that all parts and hardware previously removed are properly
replaced.
FUNCTION CHECK: After installation also make sure that no moving parts are
obstructed and function of the vehicle is not hindered in any way. Cables and
hoses must not rub and/or be pinched. Before starting to ride, perform a
comprehensive check of all functions. Regularly check (every 100 km] for the
proper seating of all parts and connections removed during installation.
PRODUCT SPECIFIC INFORMATION
ATTENTION: Pay attention to the mounting instructions included to the
panniers!
PARTS LIST
No.| Art.-Nr. /
Item No. /| Part| Quantity| N-m
---|---|---|---|---
1| HTA.07.740.015 (L/R]| Mounting Bracket [left & right side)| 2/ 2|
2| HTA.00.740.010| Connector-Part Female| 2/ 2|
3| M5 x 16; DIN 6912| Hexagon Socket Screw, short Head; black| 6/6|
4| M5 x 20; DIN 6912| Hexagon Socket Screw, short Head; black| 2/ 2|
5| d 5,3; DIN 9 0 2 1| Washer| 2/ 2|
6| M5; DIN 6927| Lock Nut with Flange| 8/8|
7| HTA.07.740.008 (L/R]| Panniers Frame [ left & right side)| 2/ 2|
8| HTA.00.740.011 (L/R]| Seite) Connector-Part Male ( left & right side )|
2/ 2|
9| M5 x 12; DIN 912| Hexagon Socket Screw; black| 4 /4|
10| M5; DIN 985| Lock Nut| 4 /4|
11| KES.RD.150.0200.02.GL| Plastic Plug| 2/ 2|
12| M8 x 55; DIN 912| Hexagon Socket Screw| 4 /4|
13| d 8,4; DIN 125| Washer| 4 /4|
14| 1 5 /8,4/23| Spacer| 4 /4|
15| BC.HTA.00.740.1100+/B| BLAZE® H Panniers| 1/ 1|
The second number indicates the total quantity of the listed part in the delivery.
MOUNTING
Attach the shown parts on the mounting brackets [1] ( right side mounting
bracket shown).
ATTENTION: At first just tighten the screws (3) as specified in the parts
list!
Over-tightening the screws will damage the plastic parts!
The shown buckles will come with your panniers. Attach them as shown.
ATTENTION: Tighten screws (4) after attaching the panniers.
Pay attention t o the torque specified i n the parts list!
NOTE: Please pay attention to the information sheet included to the
panniers.
Attach the support arms (7) to the connectors ( 8 ) , as shown in the drawing.
ATTENTION: Connect the “L” connector to the “L” support arm;
Then connect the components marked with “R”! Also make sure the engraving o f
the support arms is located as shown i n the detail drawing!
ATTENTION: Tighten the screws (9) as specified in the parts list !
Over-tightening the screws will damage the plastic parts!
ATTENTION: Make sure the support arms fit properly after tightening the
screws!
NOTE: The installation is shown on the left side of the vehicle only.
Repeat the same procedure on the right side of the vehicle with the
appropriate parts.
Remove the original screws from the mounting point. Attach the mounting
brackets (1) with the passenger footrests mounts, as shown in the draw ing .
ATTENTION: Use liquid thread locker!
Tighten the screws as specified in the parts list.
Pay attention to the audible clicking sound. Before riding check the proper fit of the panniers frames.
Revision:00 – Datum / Date: 09 – 2020
PRO BLAZE® saddlebags
PRO BLAZE® saddlebags high version
Thank you for choosing this premium product from SW-MOTECH.
Please visit our webshop for additional information, such as application
charts and PDF mounting instructions. Any other documents that may be required
(e.g. ABE certifications), are also available for download at our webshop.
Installation and/or maintenance of this product require good technical
understanding! For your own safety SW-MOTECH recommends having installation
and/or servicing carried out by a specialist workshop!
SW-MOTECH assumes no Liability for damage caused by improper installation
and/or maintenance work!
Carefully follow all the directions given in the mounting instructions and pay
attention to all relevant information in the vehicle manual during assembly.
Nonconformance can lead to vehicle damage or even endanger the driver!
These mounting instructions are written based on our current state of
knowledge. Legal requirements for accuracy do not exist.
This product was developed for vehicles in their factory setting.
Compatibility with original accessory parts or other manufacturers’ accessory
parts is not guaranteed. Furthermore, BEFORE installing this product, make
sure that all moving parts (e.g. the chain) are in the original state of
maintenance.
Installed accessories can change the driving behaviour and/or stability of
your vehicle,
GENERAL INFORMATION
Observe the country-specific regulations concerning vehicle registration/
operation as well as TUV regulations if applicable. If required, register
installed parts in the vehicle documents through an appropriate inspection
authority.
PREPARATION: Read the mounting instructions carefully and make sure that all
items of the parts list are included. Make sure that your vehicle is parked
safely and cannot fall over. Turn off the engine and remove the ignition key.
Let the motor/exhaust cool off if necessary. Disconnect the vehicle battery
when working on the electrical system. Use appropriate tools. Have another
person to help you.
FUNCTION CHECK: After fixation also make sure that no moving parts are
obstructed and the function of the vehicle is not hindered in any way. Lamps
as taillight and turn signals must not be limited in their function. Cables
and hoses must not rub and/or be pinched. Before starting to ride, perform a
comprehensive check of all functions.
ATTENTION: Before riding and at each stop (every 200 km) check proper fixation
of the product!
ATTENTION: Compatibility with accessory exhaust systems cannot be guaranteed!
All components of the product must not contact any hot or moving parts of the
vehicle. All parts should also remain 5 cm away from hot parts of the vehicle
and remain clear of the exhaust stream. For this reason compress the
suspension fully several times with your vehicle stationary.
PRODUCT SPECIFIC INFORMATION
ATTENTION: Riding with this product may affect the motorcycles driving
and braking performance! Cornering and ground clearance can be reduced by
using this product!
ATTENTION: Modifications will void any warranty.
ATTENTION: The maximum vehicle load specified by the manufacturer must
not be exceeded!
ATTENTION
NOT FOR OFFROAD-USE!
No.| Art.-Nr. /
Item No. /| Part| Quantity| N-m
---|---|---|---|---
| BC.ZUB.00.740.30000| PRO BLAZE® Saddlebags| |
1| BC.ZUB.00.019.30000| Buckle| 2/ 2|
2| LSF.350.250| Protection Foil; 250 x 350 mm| 2/ 2|
3| BC.HTA.00.740.901.01 /902.01| Saddlebag; left / right| 2/ 2|
4| BC.ZUB.00.064.30000| Waterproof Innerbag| 2/ 2|
| | | |
| BC.ZUB.00.740.30000*| PRO BLAZE® Saddlebags| 2/ 2|
1| BC.ZUB.00.019.30000| Buckle| 2/ 2|
2| LSF.350.250| Protection Foil; 250 x 350 mm| 2/ 2|
3| BC.HTA.00.740.901.02 /902.02| Saddlebag; left / right| 2/ 2|
4| BC.ZUB.00.064.30000| Waterproof Innerbag| 2/ 2|
Coarse Thread 0| M4| M5| M6| M8| M10| M12
---|---|---|---|---|---|---
Steel CL 8.8 Nrn| 2,8| 5,5| 9,6| 23| 46| 79
Coarse Thread 0| M4| M5| Iv16| M8| M10| M12
Steel CL 10.9 N.rn| 4,1| 8,1| 14| 34| 67| 115
Note:
All measurements in millimeters.® The second number indicates the total
quantity of the part in the delivery.
©No torque specifications: Use the torque defined by vehicle manufacturer! The
standard torque in this table can b e used as long a sitis within the vehicle
manufacturer’s specifications.
FASTENING
After mounting the saddlebags frames you need to protect the surface of the
motorcycle against scratches with the included protection foil (2).
Clean the surface from grease and dirt before applying the protection film.
ATTENTION: Sharp edges have to be covered with several layers o f the
protection foil!
After mounting the saddle bags, check if the affected parts of the vehicle are
sufficiently protected against abrasion.
Slide the pannier sleeves of the saddlebags (3) on both sides onto the mounted support arms.
Fasten the saddlebags (3) with the velcro flaps over the rear
(passenger seat) of the motorcycle, as shown in the drawing .
ATTENTION: Make sure after loading the saddlebags (3) there is NO weight
on the saddlebags frames! The weight of the saddlebags (3) must be supported
by the velcro flaps, NEVER by the saddlebags frames. After loading, the
saddlebags frames must be positioned in the saddlebags sleeves, as shown in
the detail drawing!
ATTENTION: Pay attention t o the mounting instructions included to the
saddlebags support arms!
Fix the saddlebags (3) with the safety straps to the loosely mounted buckles
(1) on both sides. Then tighten the screws of the buckles (1) as described in
the mounting instructions of the saddlebags support arms.
Tighten the safety straps to secure the saddlebags (3).
ATTENTION: Make sure BEFORE each ride that the velcro flaps and safety straps
o f the saddlebags (3) are firmly tightened and there is NO weight on the
support arms!
Wrong mounted saddlebags (3) can damaged the product and vehicle! Finally roll
up the excess safty strap length and secure it. 
Use the waterproof inner bags [4) to protect your luggage from
moisture. Additionally protect sensitive luggage (e.g., electronic equipment)
from moisture with a plastic bag.
SAFETY, LOADING AND CARE
SAFETY AND LOADING: Make sure weight i s evenly distributed between the
sagglebags. Make sure that the loanding i s secured against shifting during
the ride!
Do not store sharp or fragile objects!
ONLY loop assigned SW-MOTECH products to the MOLLE attachment!
ATTENTION: Remove the support arms when driving WITHOUT saddlebags from the
vehicle!
All components of the product must not contact any hot or moving parts of the
vehicle. All parts should also remain 5 cm away from hot parts of the vehicle
and remain clear of the exhaust stream.
ATTENTION: Compatibility with accessory exhaust systems cannot be guaranteed!
ATTENTION: Surface materials can experience color changes or fadingwhen
exposed to direct sunlight for extended periods o f time and by environmental
factors (e.g., SMOG, acid rain, etc.]!
Gasoline and similar substances must be washed off immediately! SW-MOTECH
assumes no liability for color changes!
CARE: For cleaning use ONLY a soft textile brush, cloth or sponge and warm
soapy water! Rinse with clean water .
Do NOT use strong cleaning agents, rough cleaning tools or high pressure
washer!
Clean the product after riding in salty conditions, to avoid damage from salt.
Copyright by
SW-MOTECH GmbH & Co. KG
Errors and omissions expected. Technical and design-modifications are
subjects t o change.
K Packed by:
Date of packaging:
SW-MOTECH GmbH & Co. KG
Tel. /phone + 49 (0)6425 / 8168 – 050
Fax / fax + 49 (0)6425
Ernteweg 8 / 1 0/ 8168 – 1 0
35282 Rauschenberg
infofasw-motech.com
Germany
www.sw-motech.com
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>