SW-MOTECH BC.HTA.41.983.20000 Legend Gear Side Bag System Instruction Manual
- June 3, 2024
- SW-MOTECH
Table of Contents
SW-MOTECH BC.HTA.41.983.20000 Legend Gear Side Bag System
MOUNTING INSTRUCTION
Art.-Nr. / Item No.: HTA.41.983.10000 & HTA.41.983.11000
SLC side carrier
Thank you for choosing this premium product from SW-MOTECH.
Please carefully read and understand all instructions, safety messages and
warnings in this mounting instructions prior to installation and use of this
product to avoid injury.
This product was developed for vehicles in their factory setting.
Compatibility with original accessory parts or other manufacturers’ accessory
parts is not guaranteed. Visit ourwebshop for additional information, such as
application charts and PDF mounting instructions. Any other documents that may
be required (e.g. ABE certifications), are also available for download at our
webshop. Keep these mounting instructions as reference.
SW-MOTECH assumes no liability for damage caused by improper installation
and/or maintenance work!
SAFETY ALERT SYMBOL
A This safety alert symbol is used throughout these mounting instructions to
warn of the possibility of death, bodily injury or other warnings. The words
DANGER, WARNING and CAUTION are used with this safety alert symbol to convey
important safety messages and information related to the installation and use
of this product. These words along with the safety alert symbol mean:
DANGER: Indicates a hazardous situation that, if not avoided, will result
in death or serious injury!
WARNING: Indicates a hazardous situation that, if not avoided, could
result in death or serious injury!
CAUTION: Indicates a hazardous situation that, if not avoided, could
result in minor or moderate injury!
NOTICE: Important information, but not death or injury related (property
damage only)!
WARNING: The installation and/or maintenance of this product requires
advanced mechanical skills, the proper tools, and a thorough understanding of
tool use and torque specifications.
For your own safety, SW-MOTECH recommends having installation and/or
maintenance carried out by a qualified and certified motorcycle mechanic.
WARNING: Should you choose to self-install this product, carefully and
completely read all installation and safety instructions before installation
and use, and follow all the directions and safety precautions given in the
mounting instructions to avoid serious injury or death. Also pay attention to
all relevant information in the vehicle manual during installation and use.
IF YOU DO NOT UNDERSTAND ANY PART OF THESE INSTRUCTIONS, OR NEED CLARIFICATION
OF ANY INSTRUCTION, DO NOT ATTEMT TO MOUNT THIS
PRODUCT WITHOUT CONTACTING SW-MOTECH FOR ASSISTANCE.
PREPARATION: Read the mounting instructions carefully and make sure that all
items of the parts list are included.
CAUTION: Make sure that your vehicle is parked safely and cannot fall
over. Turn off the engine and remove the ignition key. Let the engine/exhaust
cool off if necessary. Disconnect the vehicle battery when working on the
electrical system. Use appropriate tools and wear always safety glasses and
hand protection. Have another person help you.
MOUNTING: All parts and connections removed from the vehicle must be
reinstalled in accordance with the vehicle manufacturer specifications or
replaced by parts and hardware delivered by SW-MOTECH.
WARNING: Secure all threads, unless otherwise specified, with medium
strong strength liquid thread locker. Torque specifications undefined by SW-
MOTECH must be obtained from the vehicle manufacturer or by a certified
motorcycle workshop!
FUNCTION CHECK: After installation also make sure that no moving parts
are obstructed, and function of the vehicle is not hindered in any way. Cables
and hoses must not rub and/or be pinched.
WARNING: Before starting to ride, perform a comprehensive check of all
functions. After the first 50 km and then at regular intervals, check the
tightening torque of all connections and the proper fit of the product.
Installed accessories can change driving behavior/stability of the vehicle.
PARTS LIST
Step| No.| Item No. Description a| Part| Quantity b|
N.m c
---|---|---|---|---|---
| | HTA.41.983.1000| SLC Side Carrier left| |
| (1)| HTA.41.983.901.01| Side Carrier; left| 1 /1|
| (2)| HT A.00.152.080| Guide Bolt| 3/3|
| (3)| HT A.00.152.081| Lock Bolt| 1 /1| 8
| (4)| M6 x 20; DIN 6912| Hexagon Socket Screw, short head| 1 /1| 8
| (5)| M6 x 20; DIN 7991| Countersunk Screw; black| 2/2| 20
| (6)| MB x 100; DIN 6912| Hexagon Socket Screw, short head| 1 /1|
| (7)| 0 8,4; DIN 125| Washer; black| 1 /2|
| (8)| 016/08,5/h 17| Spacer; height 17 mm| 1 /1|
| (9)| MB x 85; DIN 912| Hexagon Socket Screw| 1 /1| 20
| (10)| 0 8,4; DIN 125| Washer; black| 1 /2|
| (11)| 016/08,4/h 12| ! Spacer; height 12 mm| 1 /1|
| | HTA.41.983.1100| SLC Slide Carrier right| |
| (1)| HTA.41.983.902.01| Side Carrier; right| 1 /1|
| | | Mounting parts see SLC Side Carrier left| |
Note: a All measurements in millimeters. b The second number indicates the
total quantity of the part in the delivery.
c No torque specifications: Use the torque defined by vehicle manufacturer!
The standard torque in this table can be used as long as it is within the
vehicle manufacturer’s specifications.
MOUNTING
WARNING: Always wear eye and hand protection!
WARNING: Always use appropriate tools!
NOTICE: The following mounting steps show the mounting of the left side
carrier. Mount the right side carrier in the same way.
Attach the parts (2) to (5) to the side carrier (1).
WARNING: Use liquid thread locker!
Tighten the screws as specified.
Remove the original screws from the mounting points.
Attach the side carrier (1) to the vehicle.
WARNING: Use liquid thread locker!
Tighten the screws as specified.
PRODUCT SPECIFIC INFORMATION
NOTICE: Observe the country-specific regulations concerning vehicle registration/operation as well as TUV regulations if applicable. If required, register installed parts in the vehicle documents through an appropriate inspection authority.
MOUNTING INSTRUCTIONS
Art.-Nr. / Item No.: *BC.HTA.00.40.10*00***
Legend Gear Side Bag LC1 / LC2
Thank you for choosing this premium product from SW-MOTECH.
Please visit our webshop for additional information, such as application
charts and PDF mounting instructions. Any other documents that may be required
(e.g. ABE certifications), are also available for download at our webshop. »
www.sw-motech.com
Carefully follow all the directions given in the mounting instructions. Also
pay attention to all relevant information in the vehicle manual during
assembly. Nonconformance can lead to vehicle damage or even endanger the
driver! Please keep the mounting instructions as reference. SW-MOTECH assumes
no liability for damages caused by improper fixation and handling.
This product was developed for vehicles in their original condition.
Compatibility with original accessory parts or other manufacturers’ accessory
parts is not guaranteed. Installed accessories can change driving behaviour
and/or stability of your vehicle.
GENERAL INFORMATION
Please observe any country-specific regulations concerning
vehicleregistration.
PREPARATION: Read the mounting instructions carefully and make sure that
all parts are included. Make sure that your vehicle is parked safely and
cannot fall over. Turn off the engine and remove the ignition key. Let the
motor/exhaust cool off if necessary. Make sure to use only the appropriate
tools. During installation have another person help you.
FUNCTION CHECK: This is a universal product. For this reason make sure
BEFORE the first use, that the product can be fixed properly and used without
problems with your vehicle type.
ATTENTION: All components of the product must not contact any hot or
moving parts of the vehicle. All parts should also remain 5 cm away from hot
parts of the vehicle and remain clear of the exhaust stream. After mounting,
make sure there are no clearance issues while the suspension is both
compressed and extended.
ATTENTION: Before riding and at each stop (every 200 km) check proper
fixation of the product!
After fixation also make sure that no moving parts are obstructed and the
function of the vehicle is not hindered in any way. Lamps as taillight and
turn signals must not be limited in their function. Cables and hoses must not
rub and/or be pinched. Before starting to ride, perform a comprehensive check
of all functions.
LOADING INFORMATION
ATTENTION: Riding with this product may affect the motorcycles driving and
braking performance! Make sure weight is evenly distributed!
ATTENTION: Depending on the location of fixation, cornering and ground
clearance can be reduced by using this product!
Never store pointy or sharp-edged objects in the product, which could cause
injury to persons or damage to the vehicle/product.
Use a waterproof inner bag/raincover to protect your luggage from
moisture.
Additionally protect sensitive luggage (e.g., electronic equipment) from
moisture with a plastic bag.
ATTENTION: Maximum load: 5 kg/ 11 lbs! The maximum vehicle load specified
by the manufacturer must not be exceeded!
ATTENTION: Maximum speed with this product, 130 km/h!
PARTS LIST & CARE
CARE
Clean the product periodically or after each trip, as dust and dirt have a
wear-effect and permanent stains can be prevented. Clean the product after
riding in salty conditions, to avoid damage from salt.
First remove dust and encrustations with a soft dry brush. Remove stubborn
deposits with a soft cloth and warm soapy water. Do NOT use strong cleaning
agents, rough cleaning tools or high pressure washer! Then rinse with clear
water.
Before re-use dry the product for at least 24 hours in the air (not in direct
sunlight).
We recommend to impregnate the cotton textile surface of the product in
regular intervals or after intensive cleaning with a commercial wax
impregnation (e.g. from Fjallravenl.
ATTENTION: Because the textile surfaces material is a natural fiber, it
will experience color changes or fading when exposed to direct sunlight for
extended periods of time and by environmental factors (e.g., SMOG, acid rain,
etc.)! SW-MOTECH assumes no liability for this!
ATTENTION: Dirt on the product and vehicle has an abrasive effect and can
damage surfaces, such as the paint. Make sure that all areas of the vehicle,
which have contact with the product or parts of the product as straps, are
protected with an adhesive protection film from scratches and abrasions.
SW-MOTECH assumes no liability for paint damage and abrasions.
FIXATION
Fasten the Velcro closure of the side bag (1 a/1 bl.
Revert the reinforced opening of the side bag (1 a/1 bl twice completely
Fix the shown loops with the side-mounted hook buckles.
Tighten the straps of the hook buckle.
Secure the opening of the side bag (1 a/1 b) with the shown strap.
Place the three openings of the quick release fastening system onto the
locating bolts of the mounted SLC side carrier.
Press the side bag (1 a/1 bl slightly downward, until it properly rests on SLC
side carrier.
ATTENTION: Make sure that all three locating bolts engage at the same
time!
Pay attention to the clearly audible snap sound of the locking mechanism!
To release the side bag (1 a/1 bl simply press the shown slider of the locking
mechanism downward.
SW-MOTECH GmbH & Co. KG
Ernteweg 8/10 – 35282 Rauschenberg – Germany
Tel. I phone+ 49 [0)6425 / 8168 – 050
Fax/ fax+ 49 [0)6425 / 8168 – 10
info@sw-motech.com • www.sw-
motech.com
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>