SW-MOTECH BC.HTA.18.791.20000 Laegnd Gear Side Saddlebag Instruction Manual
- June 3, 2024
- SW-MOTECH
Table of Contents
SW-MOTECH BC.HTA.18.791.20000 Laegnd Gear Side Saddlebag Instruction Manual
Thank you for choosing this premium product from SW-MOTECH. Please visit our
webshop for additional information, such as application charts and PDF
mounting instructions. Any other documents that may be required (e.g. ABE
certifications), are also available for download at our webshop.
Installation and / or maintenance of this product require good technical
understanding! For your own safety SW-MOTECH recommends having installation
and / or servicing carried out by a specialist workshop! SW-MOTECH assumes no
liability for damage caused by improper installation and / or maintenance
work!
Carefully follow all the directions given in the mounting instructions and pay
attention to all relevant information in the vehicle manual during assembly.
Non conformance can lead to vehicle damage or even endanger the driver! These
mounting instructions are written based on our current state of knowledge.
Legal requirements for accuracy do not exist.
This product was developed for vehicles in their factory setting.
Compatibility with original accessory parts or other manufacturers’ accessory
parts is not guaranteed. Furthermore, BEFORE installing this product, make
sure that all moving parts (e.g. the chain) are in the original state of
maintenance. Installed accessories can change the driving behaviour and / or
stability of your vehicle.
GENERAL INFORMATION
Observe the country-specific regulations concerning vehicle registration /
operation as well as TUV regulations if applicable. If required, register
installed parts in the vehicle documents through an appropriate inspection
authority.
PREPARATION: Read the mounting instructions carefully and make sure that
all items of the parts list are included. Make sure that your vehicle is
parked safely and cannot fall over. Turn off the engine and remove the
ignition key. Let the motor / exhaust cool off if necessary. Disconnect the
vehicle battery when working on the electrical system. Use appropriate tools.
Have another person to help you.
MOUNTING: All parts and connections removed from the vehicle must be
reinstalled in accordance with the vehicle manufacturers’ specifications or
replaced by parts delivered by SW-MOTECH. Secure all threads, unless otherwise
specified, with medium-strength liquid thread locker. Torque specifications
undefined by SW-MOTECH must be obtained from the vehicle manufacturer or by a
specialist workshop!
FUNCTION CHECK: After installation make sure that all parts and
connections previously removed are properly replaced. Also make sure that no
moving parts are obstructed and no function of the vehicle is hindered in any
way. Cables and hoses must not rub and / or be pinched. Before starting to
ride, perform a comprehensive check of all functions. After the first 50 km
and then at regular intervals, check the tightening torque of all screw
connections and the proper fit of the product.
No.| Item No./ Description| Part| Quantity|
Nm
---|---|---|---|---
I (1)| HTA.18.791.901.01| Side Carrier (Left side)| in|
(2)| HTA.00.152.080| Guide Bolt| 3 /3|
(3)| HTA.00.152.081| Lock Bolt| hi|
(4)| M6 x 20; DIN 6912| Hexagon Socket Screw, short head| 1 /1| 7
(5)| M6 x 20; DIN 7991| Countersunk Screw; black| 212| 7
1 (6)| UNC V2″ x 5″ (12,7 x 127); 12.9| Hexagon Socket Screw with Inch Thread|
1 n|
(7)| HTA.18.791.004| Spring Strut Spacer| hi|
(8)| UNC 3/s” x 3″ (9,525 x 76,2); 12.9| Hexagon Socket Screw with Inch
Thread| 111|
(9)| 0 16 / 0 10,5 / h 8| Spacer| 111|
HTA.18.791.902.01
| Legend Gear Side Carrier SLC right|
---|---|---
(1) HTA.18.791.902.01| Side Carrier (right side)| 1/1
(2) HTA.00.152.080| Guide Bolt| 3 /3
(3) HTA.00.152.081| Lock Bolt| 1 n
(4) M6 x 20; DIN 6912| Hexagon Socket Screw, short head| 1n 7
(5) M6 x 20; DIN 7991| Countersunk Screw; black| 2/2 7
(6) UNC1/2– x 5″ (12,7 x 127); 12.9| (7) Hexagon Socket Screw with Inch
Thread| 1 /1
(8) HTA.18.791.004| Spring Strut Spacer| 1 i i
(9) UNC 3/13– x 3″ (9,525 x 76,2); 12.9| Hexagon Socket Screw with Inch
Thread| 1 is
(10)0 16 / 0 10,5 /h 8| Spacer| 1 /1
8.8| Regelgewinde / Coarse Thread 0| M4| M5| M6|
M8| M10| M12| 10.9| Regelgewinde / Coarse Thread| M4|
145| 146| 148| /410| M12
---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---
Stahl; FK 8.8 / Steel; CL 8.8 Nm| 2,8| 5,5| 9,6| 23| 46| 79| Stahl;
FK 10.9 / Steel; CL 10.9 Nm| 4,1| 8,1| 14| 34| 67| 115
- All measurements in millimeters.
** The second number indicates the total quantity of the part in the delivery.
*** No torque specifications: Use the torque defined by vehicle manufacturer!
The standard torque in this table can be used as long as it is within the vehicle manufacturer‘s specifications.
MOUNTING
NOTE: This mounting step shows the mounting on the left side carrier.
Repeat the same procedure on the right side with the parts of the right side
carrier.
Attach the parts (2) to (5) to the side carrier (1), as shown in the drawing.
ATTENTION: Use Liquid thread Locker!
Tighten the screws as specified in the parts list.
ATTENTION: Before starting the mounting, unload the spring struts with a
suitable jack, as shown in the detail drawing!
Remove the seat from the vehicle.
NOTE: The mounting steps [3], [4] and [5] show the mounting of the left
side carrier to the vehicle. Repeat the same procedure on the right side with
the parts of the right side carrier.
Remove the original screw from the vehicle frame.
Loosen the shown nuts and screw and remove the spring strut from the vehicle.
The spring strut bolt and cap nut are not required for assembly (please
store).
Attach the side carrier (1) to the vehicle, as shown in the drawing. Use the
shown original parts (Orig.).
ATTENTION: Use Liquid thread Locker!
Tighten the screws with the manufacturer’s specified torque.
Finally reattach the seat.
Thank you for choosing this premium product from SW-MOTECH.
Please visit our webshop for additional information, such as application
charts and PDF mounting instructions. Any other documents that may be required
(e.g. ABE certifications), are also available for download at our webshop. »
www.sw-motech.com Carefully follow all the
directions given in the mounting instructions. Also pay attention to all
relevant information in the vehicle manual during assembly. Nonconformance can
lead to vehicle damage or even endanger the driver! Please keep the mounting
instructions as reference. SW-MOTECH assumes no liability for damages caused
by improper fixation and handling. This product was developed for vehicles in
their original condition. Compatibility with original accessory parts or other
manufacturers’ accessory parts is not guaranteed. Installed accessories can
change driving behaviour and/or stability of your vehicle.
GENERAL INFORMATION
Please observe any country-specific regulations concerning vehicle
registration.
PREPARATION: Read the mounting instructions carefully and make sure that
all parts are included. Make sure that your vehicle is parked safely and
cannot fall over. Turn off the engine and remove the ignition key. Let the
motor/exhaust cool off if necessary. Make sure to use only the appropriate
took. During installation have another person help you.
FUNCTION CHECK: This is a universal product. For this reason make sure
BEFORE the first use, that the product can be fixed properly and used without
problems with your vehicle type.
ATTENTION: All components of the product must not contact any hot or
moving parts of the vehicle. All parts should also remain 5 cm away from hot
parts of the vehicle and remain clear of the exhaust stream. After mounting,
make sure there are no clearance issues while the suspension is both
compressed and extended.
ATTENTION: Before riding and at each stop (every 200 km( check proper
fixation of the product! After fixation also make sure that no moving parts
are obstructed and the function of the vehicle is not hindered in any way.
Lamps as taillight and turn signals must not be limited in their function.
Cables and hoses must not rub and/or be pinched. Before starting to ride,
perform a comprehensive check of all functions.
LOADING INFORMATION
ATTENTION: Riding with this product may affect the motorcycles driving
and braking performance! Make sure weight is evenly distributed!
ATTENTION: Depending on the location of fixation, cornering and ground
clearance can be reduced by using this product! Never store pointy or sharp-
edged objects in the product, which could cause injury to persons or damage to
the vehicle/product. Use a waterproof inner bag/raincover to protect your
luggage from moisture. Additionally protect sensitive luggage (e.g.,
electronic equipment) from moisture with a plastic bag.
ATTENTION: Maximum load: 5 kg / 11 lbs! The maximum vehicle load
specified by the manufacturer must not be exceeded!
ATTENTION: Maximum speed with this product: 130 km/h!
PARTS LIST & CARE
Features (from left to right): Quick release fastening system; Loops for the shoulder strap (sold separately); Waterproof Innerbag.
1x Waterproof Innerbag
CARE
Clean the product periodically or after each trip, as dust and dirt have a wear-effect and permanent stains can be prevented. Clean the product after riding in salty conditions, to avoid damage from salt.
First remove dust and encrustations with a soft dry brush. Remove stubborn deposits with a soft cloth and warm soapy water. Do NOT use strong cleaning agents, rough cleaning tools or high pressure washer! Then rinse with clear water.
Before re-use dry the product for at least 24 hours in the air (not in direct sunlight). We recommend to impregnate the cotton textile surface of the product in regular intervals or after intensive cleaning with a commercial wax impregnation (e.g. from Fjallr5ven).
ATTENTION: Because the textile surfaces material is a natural fiber, it
will experience color changes or fading when exposed to direct sunlight for
extended periods of time and by environmental factors (e.g., SMOG, acid rain,
etc.)! SW-MOTECH assumes no liability for this!
ATTENTION: Dirt on the product and vehicle has an abrasive effect and can
damage surfaces, such as the paint. Make sure that all areas of the vehicle,
which have contact with the product or parts of the product as straps, are
protected with an adhesive protection film from scratches and abrasions. SW-
MOTECH assumes no liability for paint damage and abrasions.
FIXATION
Fasten the Velcro closure of the side bag (1 an b). Revert the reinforced
opening of the side bag Ilan b) twice completely.
Fix the shown loops with the side-mounted hook buckles.
Tighten the straps of the hook buckle.
Secure the opening of the side bag (l a/1 b) with the shown strap.
Place the three openings of the quick release fastening system onto the
locating bolts of the mounted SLC side carrier.
Press the side bag (lan b) slightly downward, until it properly rests on SLC side carrier.
ATTENTION: Make sure that all three locating bolts engage at the same time! Pay attention to the clearly audible snap sound of the locking mechanism!
To release the side bag (1 an b) simply press the shown slider of the locking
mechanism downward.
Fixation and vehicle are examples.
Copyright by
SW-MOTECH GmbH & Co. KG
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>