PRESIDENT ANDY II FCC CB Radio Owner’s Manual
- June 6, 2024
- PRESIDENT
Table of Contents
Owner’s manual
WARNING: This product can expose you to chemicals including Lead, which
is known to the State of California to cause cancer and birth defects, or
other reproductive harm. For more information go to
www.P65Warnings.ca.gov.
WARNING!
Before using, be careful never to transmit without first having connected the
antenna (connection “B” situated on the back panel of the equipment) or
without having set the SWR (Standing Wave Ratio) ! Failure to do so may result
in the destruction of the power amplifier, which is not covered by the
warranty.
The warranty of this transceiver is valid only in the country of purchase.
Welcome to the world of the new generation of CB radios. The new PRESIDENT
range gives you access to top-performance CB equipment. With the use of up-to-
date technology, which guarantees unprecedented quality, your PRESIDENT ANDY
II FCC is a new step in personal communication and is the surest choice for
the most demanding of professional CB radio users. To ensure that you make the
most of all its capacities, we advise you to read carefully this manual before
installing and using your PRESIDENT ANDY II FCC.
INSTALLATION
1) WHERE AND HOW TO MOUNT YOUR MOBILE CB RADIO
a) You should choose the most appropriate setting from a simple and practical
point of view.
b) Your CB radio should not interfere with the driver or the passengers.
c) Remember to provide for the passing and protection of different wires (e.g.
power, antenna, accessory cabling) so that they do not in any way interfere
with the driving of the vehicle.
d) To install your equipment, use the cradle (1) and the self-tapping screws
[2] provided (drilling diameter 3.2 mm). Take care not to damage the vehicle’s
electrical system while drilling the dash board.
e) Do not forget to insert the rubber joints (3) between the CB and its
support as these have a shock-absorbing effect which permits gentle
orientation and tightening of the set.
f) Choose where to place the microphone support and remember that the
microphone cord must stretch to the driver without interfering with the
controls of the vehicle.
– Note: As the transceiver has a frontal microphone socket, it can be set into
the dash board. In this case, you will need to add an external loud speaker to
improve the sound quality of commu- nications (connector EXT.SP situated on
the back panel: C). Ask your dealer for advice on mounting your CB radio.
2) ANTENNA INSTALLATION
a ) Choosing your antenna
– For CB radios, the longer the antenna, the better its results. Your dealer
will be able to help you with your choice of antenna.
b) Mobile antenna
– Must be fixed to the vehicle where there is a maximum of metallic surface
(ground plane), away from windscreen mountings.
– If you already have a radio-telephone antenna installed, the CB antenna
should be higher than this.
– There are two types of antenna: pre-regulated which should be used on a good
ground plane (e.g. car roof or lid of the boot), and adjustable which offer a
much larger range and can be used on a smaller ground plane (see § 5 page 7,
ADJUSTMENT OF SWR).
– For an antenna which must be fixed by drilling, you will need a good contact
between the antenna and the ground plane. To obtain this, you should lightly
scratch the surface where the screw and tightening star are to be placed.
– Be careful not to pinch or flatten the coaxial cable (as this runs the risk
of break down and/or short-circuiting).
– Connect the antenna (B).
c) Fixed antenna
– A fixed antenna should be installed in a clear space as possible. If it is
fixed to a mast, it will perhaps be necessary to stay it, accord- ing to the
laws in force (you should seek professional advice). All PRESIDENT antennas
and accessories are designed to give maximum efficiency to each CB radio
within the range.
3) POWER CONNECTION
Your PRESIDENT ANDY II FCC is protected against an inversion of polarities.
However, before switching it on, you are advised to check all the connections.
Your equipment must be supplied with a continued current of 12 or 24 volts
(A). Today, most cars and trucks are negative earth. You can check this by
making sure that the negative terminal of the battery is connected either to
the engine block or to the chassis. If this is not the case, you should
consult your dealer.
a) Check that the battery is of 12 or 24 volts.
b) Locate the positive and negative terminals of the battery (+ is red and –
is black). Should it be necessary to lengthen the power cable, you should use
the same or a superior type of cable.
c) It is necessary to connect your CB to a permanent (+) and (-). We advise
you to connect the power cable directly to the battery (as the connection of
the CB cable to the wiring of the car-radio or other parts of the electrical
circuit may, in some cases, increase the likelihood of interference).
d) Connect the red wire (+) to the positive terminal of the battery and the
black (-) wire to the negative terminal of the battery.
e) Connect the power cable to your CB radio.
WARNING: Never replace the original fuse by one of a different value.
4) BASIC OPERATIONS TO BE CARRIED OUT BEFORE USING YOUR SET FOR THE FIRST
TIME (without transmitting and without using the «push-to-talk» switch on
the microphone)
a) Connect the microphone,
b) Check the antenna connections,
c) Turn the set on by turning the volume knob VOL (1) clockwise,
d) Turn the squelch SQ knob (4) to minimum (M position),
e) Adjust the volume to a comfortable level,
f) Go to Channel 20 using the / keys (3).
5) ADJUSTMENT OF SWR (Standing wave ratio)
WARNING: This must be carried out when you use your CB radio for the
first time (and whenever you re-position your antenna). The adjustment must be
carried out in an obstacle-free area.
* Adjustment with external SWR-meter (e.g. PRESIDENT TOS-1)
a) To connect the SWR meter
– Connect the SWR meter between the CB radio and the antenna as close as
possible to the CB (use a maximum of 15.75 inches (40 cm) cable, type
President CA-2C).
b) To adjust the SWR meter
– Set the CB on channel 20.
– Put the switch on the SWR-meter to position FWD (calibration).
– Press the «push-to-talk» switch on the microphone to transmit.
– Bring the index needle to by using the calibration key.
– Change the switch to position REF (reading of the SWR level). The reading on
the Meter should be as near as possible to 1. If this is not the case, re-
adjust your antenna to obtain a reading as close as possible to 1 (an SWR
reading between 1 and 1.8 is acceptable).
– It will be necessary to re-calibrate the SWR meter after each adjustment of
the antenna.
WARNING: In order to avoid any losses and attenuations in cables used for
connection between the radio and its accessories, PRESIDENT recommends to use
a cable with a length less than 118.11 inches (3 m).
Your CB is now ready for use.
HOW TO USE YOUR CB
1) ON/OFF – VOLUME
a) To turn the set on, turn the VOL knob (1) clockwise.
If the KEY BEEP function is activated, 4 tones sound when you turn the CB
radio on. See § KEY BEEP page 10. Display briefly shows the microphone type
(see § MICROPHONE TYPE page 10).
See FUNCTIONS TURNING ON THE UNIT on page 10.
b) To increase the sound level, turn the same knob further clockwise.
2) DISPLAY
It shows all functions:
The BARGRAPH shows the reception level and the output power level.
3) CHANNEL SELECTOR: / keys ~ SCAN CHANNEL SELECTOR (short press)
These keys allow increasing or decreasing a channel. A «beep» sounds each time
the channel changes if the KEY BEEP function is activated. See § KEY BEEP page
10.
SCAN (very long press)
CB Channel Scan
Press and hold the (3a) or (3b) key, until a quick loop of all the 40
channels has been done, to activate the SCAN function. If the KEY BEEP
function is activated (see § KEY BEEP on page 10) a tone sounds. The dot
between the two digits of the channel number blinks on the display. Use
key (3a) for increasing way or (3b) for decreasing way. During the
scanning you can change the way by pressing the other key. The scanning stops
as soon as there is a busy channel. The scanning automatically starts 3
seconds after the end of the transmission and no key is activated during 3
seconds.
Press any key (5, 6, 7 or 8) or the PTT switch (11) to deactivate the CB
channels SCAN. The dot disappears on the display.
Weather Channel Scan
Activate the WX mode (See § CB/WX on page 8). Press and hold the (3a) or (3b)
key until a quick loop of all the 7 weather channels has been done to activate
the SCAN function. If the KEY BEEP function is activated (see § KEY BEEP on
page 10) a tone sounds. The dot between the two digits of the channel number
appears on the display. Use key (3a) for increasing way and (3b) for
decreasing way. During the scanning you can change the way by pressing the
other key. The scanning stops as soon as an alert is detected on a channel.
The scanning automatically starts 3 seconds after the end of the transmission
and no key is activated during 3 s.
Long press the NB key (5) to deactivate the Weather channels SCAN. The dot
disappears on the display.
You can turn the Weather Channels SCAN in background and return in CB mode by
pressing the CB/WX key (6).
4) ASC (Automatic Squelch Control) / SQUELCH
Suppresses undesirable background noises when there is no communication.
Squelch does not affect neither sound nor transmission power, but allows a
considerable improvement in listening comfort.
a) ASC: AUTOMATIC SQUELCH CONTROL
Worldwide patent, a PRESIDENT exclusivity
Turn the SQ knob (4) anti-clockwise into ASC position. «AS appears on the
display. No repetitive manual adjustment and a permanent improvement between
the sensitivity and the listening comfort when ASC is active. This function
can be disconnected by turning the switch clockwise. In this case the squelch
adjustment becomes manual again. SC» disappears from the display.
b) MANUAL SQUELCH
Turn the SQ knob (4) clockwise to the exact point where all background noises
disappear. This adjustment should be done with precision as, if set to maximum
(fully clockwise), only the strongest signals will be received.
5 ) NB ~ COMPANDER
NB (short press)
NOISE BLANKER : This filter facilitates the reduction of back ground
noise, and some reception interference. Short press the NB key (5) to
activate/deactivate the NB filter. “NB” appears on the display when the filter
is active.
COMPANDER **C**(long press)
Long press the **C**key (5) to activate/deactivate the Compander filter. “ **C** ” appears on the display when the filter is active. Compander : this
switchable filter allows you to improve the reception mode.
6) CB/WX ~ ALERT
CB/WX (short press)
Short press the CB/WX key (6) to alternate between the CB and WX (Weather
Channel) mode. When the WX mode is active, “WX” appears on the display. The WX
mode allows you to hear weather information. When the mode is activated, use /
key (3) to move through the 7 weather channels to find the active channel in
your local area.
Note: VOX, NB and are not allowed in WX mode. If user presses a not
allowed key and KEY BEEP function is activated, the radio sounds error tone.
ALERT (long press)
The SIREN tone only sounds in CB and PA mode. It does not sound in WX mode.
Press and hold the ALERT key (6) for 1 second to activate (“ALERT” appears on
the display) / deactivate (“ALERT” disappears on the display) the ALERT
function.
When the function is active and a tone is detected at the selected weather
channel, then the unit sounds SIREN tone. “ALERT” and the weather channel
blink on the display. The unit cancels CB or PA mode and goes to WX mode.
During a SIREN tone sound, press any key to stop the sound, “ALERT” and the
Weather Channel stop blinking on the display.
Note: The SIREN tone sounds when an ALERT is detected in the selected weather
channel only. Use first SCAN function in WX mode to detect the alerts in all
the weather channel (see § CB/ WX page 8).
7) EMG ~ EMG STORE
EMG (short press)
Emergency channels will be automatically selected by pressing the EMG key (7).
First press : emergency channel 1 is activated. Second press: emergency
channel 2 is activated. Third press: return to the current channel. “EMG”
appears on the display when an emergency channel is activated. The default
emergency channels are channel 9 (1) and channel 19 (2).
Note : Activating an emergency channel prevents use the PA (see § PA page
11) mode. If the KEY BEEP function is activated, an error beep sounds.
EMG STORE (long press)
Emergency channel can be stored to any channel. To set a new emergency
channel:
– Short press the EMG key (7) to call the current emergency channel.
“EMG” appears on the display.
– Long press the EMG/STORE key (7). appears on the display and “EMG” blinks.
– Using the / keys (3), select the new emergency channel.
– Short press the PTT switch (11) to validate and store the new emergency
channel. A validation beep sounds.
Note : Emergency setting is not allowed if the active channel is not an
emergency channel.
8) VOX ~ VOX SET
VOX (short press)
The VOX function allows transmitting by speaking into the original microphone
(or in the optional vox microphone) without pressing the PTT switch (11). The
use of an optional vox microphone connected to the rear panel of the
transceiver
(E) disables the original microphone.
Press shortly the VOX key (8) in order to activate the VOX function.
«VOX» appears on the display. A new press on the VOX (8) key disables the
function, «VOX» disappears.
VOX SET (long press)
-
Long press the VOX/SET key (8) to enter the VOX SETTING. “VOX” blinks, the current setting and its value appear on the display.
Three parameters allow to adjust the VOX: Sensitivity: L / Anti-vox level: A / Vox delay time: t. -
2a. Use the / key (3) to modify the current parameter then, press the NB key (5) to select the next parameter or….
2b. Press first the NB key (5) to select another parameter and then use the / key (3) to modify the current parameter. -
When all adjustments are done, press the PTT switch (11) to store and exit. If the KEY BEEP function is activated, a long beep sounds to confirm the success of the operation (see § KEY BEEP page 10).
-
If no key is pressed for 10 seconds, the unit automatically exits the function VOX SETTING without saving.
– Sensitivity L: allows the adjustment of the microphone (original one or optional vox) for an optimum transmission quality. Adjustable level from L1 (high level) to L9 (low level). Default value: L5.
– Anti-Vox A: allows disabling the transmission generated by the surrounding noise. The level is adjustable. AF (according the squelch level) and from A0 (without anti-vox) to A9 (low level).
Default value: AF.
– Delay time E: allows avoiding the sudden cut of the transmission by adding a delay at the end of speaking. The level is adjustable from t1 (short delay) to t9 (long delay). Default value: t1.
VOX SETTING doesn’t activate the VOX function.
- USB CHARGING SOCKET
The USB socket (9) can be used to charge a smartphone, tablet or other rechargeable device with 5 V – 2.1 A. - 4 PIN MICROPHONE PLUG
The plug is located on the front panel of the transceiver and makes the setting of the equipment into the dashboard easier.
See § MICROPHONE TYPE page 10.
See cabling diagram page 52. - PTT (Push To Talk)
Transmission key, press to transmit a message, is displayed and release to listen to an incoming communication.
See FUNCTIONS WITH PTT SWITCH on page 11.
TOT (Time Out Timer)
If the transmission key is longer than 3 minutes, active channel and start blinking, the transmission ends.
The time-out tone will sound until the PTT switch (11) is released.
A) DC-POWER TERMINAL (13.2 V / 26.4 V)
B) ANTENNA CONNECTOR (SO-239)
C) EXTERNAL SPEAKER JACK (8 Ω, Ø 3.5 mm)
D) PA SPEAKER JACK (8 Ω, Ø 3.5 mm)
E) OPTIONAL VOX MIKE (Ø 2.5 mm)
FUNCTIONS TURNING ON THE UNIT
5 more functions are available. Turn off the unit. Turn on the radio while pressing one or two keys to set the function.
- ROGER BEEP ( key)
The ROGER BEEP sounds when the PTT switch (11) of the microphone is released in order to let your correspondent speak. Historically as CB is a “simplex” communication mode, it is not possible to speak and listen at the same time (as it is the case with a telephone).
Once the conversation was over, he said “Roger” in order to let his correspondent know that it was his turn to talk. The word “Roger” has been replaced by a significant beep. That is where the name “Roger beep” comes from.
– Turn on the power while pressing the s key (3a) to alternate between enable (On) or disable (OF) the ROGER BEEP function.
– When function is activated, “ ” appears on the display.
Note: The Roger beep also sounds in the loudspeaker if the KEY BEEP function is active. If the KEY BEEP function is not active, only the orrespondent can hear the ROGER BEEP.
In PA mode the function is not allowed.
2 ) KEY BEEP (t key)
Some operations such as changing channels, pressure on keys etc.
are confirmed by a beep tone. This beep tone can be activated or deactivated as follows:
– Turn on the power while pressing the t key (3b) to alternate between enable (On) or disable (OF) the KEY BEEP function.
– When function is activated, “BP” appears on the display. - MICROPHONE TYPE (NB key)
Your ANDY II FCC allows you to use a dynamic or electret microphone.
To select the type:
– Turn on the power while pressing the NB (5) key. The symbol of the current microphone type dYna (dynamic) or ELeC (electret) is displayed. Repeat this action to set the correct microphone type.
Original 4 pins PRESIDENT microphone is electret type. - COLOR (CB/WX + EMG keys)
– Turn on the power while pressing the CB/WX (6) and EMG (7) keys.
The symbol of the current color, among the seven, blinks: (9r- ange), (green), 6L(blue), (cyan), 9E(yellow), (purple) or CL(cyan light).
– Use the / keys (3) to change the color.
– When the color is set, long press the NB key (5) or the PTT switch
(11). A beep sounds, the characters of the color are displayed during 1
second.
5) RESET (EMG key)
– Turn on the power while pressing the EMG key (7) to reset to the factory
settings.
– “rS” blinks in the display.
– Press the NB key (5) for 1 second to confirm.
FUNCTIONS WITH PTT SWITCH
4 more functions are available. To activate the function press and hold the PTT switch (11) and press the function key. Repeat this process to deactivate the function.
-
TALKBACK (PTT + NB key)
The TALKBACK function can be activated or deactivated as follows:
a) Press and hold the PTT switch (11)
b) Short press on NB key (5). Current TALKBACK level blinks 3 times allowing you to adjust this level.
When function is activated, “TB” appears on the display.
This function allows to ear your own modulation with the CB speaker. -
TALKBACK LEVEL (PTT + s/t)
– At step b) adjust the TALKBACK level using the s/t keys (3).
– When the function is on and “TB” is shown on the display, press and hold the PTT switch (11), then use the s (3a) / t (3b) keys to select the level. 9 levels from 01 to 09. -
PA (PTT + CB/WX key)
– Press and hold the PTT switch (11)
– Short press on CB/WX key (6) to alternate between CB and PA (Public Address) mode. An external loud speaker can be con-nected to your ANDY II FCC by the PA jack plug situated on the back panel PA.SP (D). The CB message received or transmitted into the microphone will be directed towards the external speaker and be amplified. Adjust the PA volume with VOL key (1).
When PA mode is activated, “PA” and “AM” blink alternatively.
When PTT switch (11) is pressed, “PA” replace the active channel on the display. Release the PTT switch (11) to display again the active channel. -
NOISE GATE (PTT + VOX)
– Press and hold the PTT switch (11).
– Short press the VOX key (8) to activate (On) or deactivate (OF) the NOISE GATE. “**NG**” Is displayed when the function is active. Noise Gate: Prevents amplification of background noise. This results in optimized signal levels.
TECHNICAL CHARACTERISTICS
GENERAL
– Channels : 40
– Modulation modes : AM
– Frequency ranges : from 26.965 MHz to 27.405 MHz
– Weather channels : 162.400 MHz to 162.550 MHz
– Antenna impedance : 50 ohms
– Power supply : 13.8 V / 27.6 V
– Dimensions : 4.92 (W) x 7.09 (D) x 1.77 (H) inches
125 (W) x 180 (D) x 45 (H) mm
– Weight : ~ 1.98 lbs / 0.9 kg
– Accessories supplied : Electret microphone with support, mounting cradle,
screws.
– Filter : ANL (Automatic Noise Limiter) built-in
TRANSMISSION
– Frequency allowance: +/- 200 Hz
– Carrier power : 4 W
– Transmission interference : inferior to 4 nW (- 54 dBm)
– Audio response : 300 Hz to 3 KHz
– Emitted power in the adj. channel : inferior to 20 µW
– Microphone sensitivity : 7 mV
– Maximum drain : 1.7 A at 13.8 V / 0.85 A at 27.6 V
– Modul. signal distortion : 2 %
RECEPTION
– Maxi. sensitivity at 20dB sinad : 0.5 µV – 113 dBm AM / 0.35 µV – 116 dBm WX
– Frequency response : 300 Hz to 3 kHz
– Adjacent chan. selectivity : 60 dB
– Maximum audio power : 2.5 W
– Squelch sensitivity : minimum 0.2 µV – 120 dBm maximum 1 mV – 47 dBm
– Frequency image rejection rate : 60 dB
– Intermediate frequency rejection rate : 70 dB
– Drain : 160 ~ 500 mA (13.8 V) 120 ~ 250 mA (27.6 V)
TROUBLE SHOOTING
-
YOUR CB RADIO WILL NOT TRANSMIT OR YOUR TRANSMISSION IS OF POOR QUALITY
– Check that the antenna is correctly connected and that the SWR is properly adjusted.
– Check that the microphone is properly plugged in. -
YOUR CB RADIO WILL NOT RECEIVE OR RECEPTION IS POOR
– Check that the squelch level is properly adjusted.
– Check that the volume is set to a comfortable listening level.
– Check that the antenna is correctly connected and that the SWR is properly adjusted. -
YOUR CB WILL NOT LIGHT UP
– Check the power supply.
– Check the connection wiring.
– Check the fuse.
HOW TO TRANSMIT OR RECEIVE A MESSAGE
Now that you have read the manual, make sure that your CB Radio is ready for
use (i.e. check that your antenna is connected). Choose your channel (19, 27).
Press the «push-to-talk» switch (11) and announce your message «Attention
stations, transmission testing» which will allow you to check the clearness
and the power of your signal. Release the switch and wait for a reply. You
should receive a reply like, «Strong and clear».
If you use a calling channel (19, 27) and you have established communication
with someone, it is common practice to choose another available channel so as
not to block the calling channel.
GLOSSARY
Below you will find some of the most frequently used CB radio expressions.
Remember this is meant for fun and that you are by no means obliged to use
them. In an emergency, you should be as clear as possible.
INTERNATIONAL PHONETIC ALPHABET
A Alpha
B Bravo
C Charlie
D Delta
E Echo
F Foxtrot
G Golf| H Hotel
I India
J Juliet
K Kilo
L Lima
M Mike
N November| O Oscar
P Papa
Q Quebec
R Romeo
S Sierra
T Tango
U Uniform| V Victor
W Whiskey
X X-ray
Y Yankee
Z Zulu
---|---|---|---
TECHNICAL VOCABULARY
AM : Amplitude Modulation
CB : Citizen’s Band
CH : Channel
CW : Continuous Wave
DX : Long Distance Liaison
DW : Dual Watch
FM : Frequency Modulation
GMT : Greenwich Meantime
HF : High Frequency
LF : Low Frequency
LSB : Lower Side Band
RX : Receiver
SSB : Single Side Band
SWR : Standing Wave Ratio
SWL : Short Wave Listening
SW : Short Wave
TX : CB Transceiver
UHF : Ultra High Frequency
USB : Upper Side Band
VHF : Very High Frequency
CB LANGUAGE
Advertising: Flashing lights of police car
Back off : Slow down
Basement : Channel 1
Base station : A CB set in fixed location
Bear : Policeman
Bear bite : Speeding fine
Bear cage : Police station
Big slab : Motorway
Big 10-4 : Absolutely
Bleeding : Signal from an adjacent channel interfering with the transmission
Blocking the channel: Pressing the PTT switch without talking
Blue boys : Police
Break : Used to ask permission to join a conversation
Breaker : A CBer wishing to join a channel
Clean and green : Clear of police
Cleaner channel : Channel with less interference
Coming in loud and proud : Good reception
Doughnut : Tyre
Down and gone : Turning CB off
Down one : Go to a lower channel
Do you copy? : Understand?
DX : Long distance
Eighty eights : Love and kisses
Eye ball : CBers meeting together
Good buddy : Fellow CBer
Hammer : Accelerator
Handle : CBer’s nickname
Harvey wall banger : Dangerous driver
How am I hitting you? : How are you receiving me?
Keying the mike: Pressing the PTT switch without talking
Kojac with a kodak : Police radar
Land line : Telephone
Lunch box : CB set
Man with a gun : Police radar
Mayday : SOS
Meat wagon : Ambulance
Midnight shopper : Thief
Modulation : Conversation
Negative copy : No reply
Over your shoulder : Right behind you
Part your hair : Behave yourself – police ahead
Pull your hammer back : Slow down
Rat race : Congested traffic
Rubberbander : New CBer
Sail boat fuel : Wind
Smokey dozing : Parked police car
Smokey with a camera : Police radar
Spaghetti bowl : Interchange
Stinger : Antenna
Turkey : Dumb CBer
Up one : Go up one channel
Wall to wall : All over/everywhere
What am I putting to you? : Please give me an S-meter reading
GENERAL WARRANTY CONDITIONS
This device is guaranteed 2 years parts and labour in its country of purchase
against any manufacturing defects validated by our technical department.
PRESIDENT After Sales Service department reserves the right not to apply the
warranty in the event a breakdown is caused by an antenna other than those
distributed by PRESIDENT. An extension of 3 years warranty is proposed
systematically for the simultaneous purchase of a device and a PRESIDENT
antenna, bringing the total duration of the warranty to 5 years. In order to
be valid, the warranty registration must be completed and submitted within a
period of 30 days after the purchase date to PRESIDENT ELECTRONICS online at
www.president-electronics.us/warranty-registration. You can also access this warranty
registration page by using your smartphone to read (application must be
available) the QR code. You will receive a confirmation email if the
registration is successfully completed. Please keep a copy of this email for
your records. Any repair under warranty will be without charge and the return
delivery costs will be borne by PRESIDENT. A proof of purchase sales receipt
must be included with the device to be repaired. The dates listed on the
warranty registration and proof of purchase must match. In case the device is
not under warranty, the repair and
return of the device will be charged. No spare parts will be sent nor
exchanged by PRESIDENT under warranty. Do not proceed with the installation of
the device without reading the user manual. The warranty is only valid in the
country of purchase.
Exclusions (not covered by Warranty):
- Damages caused by accident, shock or inadequate packaging.
- Power transistors, microphones, lights, fuses and the disrespect of the installation and use of specifications (including but not limited to antenna used with too high power, final output power transistors (SWR), inversion of polarities, bad connections, over voltage…).
- The warranty cannot be extended due to the non-availability of the device while it is being serviced at PRESIDENT After Sales Service department, nor by a change of one or more components or spare parts.
- Transceivers which have been modified. The warranty application is excluded in case of modification or poor maintenance done by a third party not approved by PRESIDENT ELECTRONICS.
If you note a malfunction:
- Check the power supply of your device and the quality of the fuse.
- Check that the antenna, the microphone are correctly connected.
- Check that the squelch level is properly adjusted; the programmed configuration is the correct one.
- In the event of a real malfunction, please contact your dealer first. He will decide what action should be taken.
In case of an intervention not covered by warranty, an estimate will be established before any repair.
Thank you for your confidence in the PRESIDENT quality and experience. We recommend that you read this manual carefully so that you are completely satisfied with your purchase.
Technical Manager
and
Quality Manager
http://www.president-electronics.us/warranty-registratio
WARNING: This product can expose you to chemicals including Lead, which is known to the State of California to cause cancer and birth defects or other reproductive harm. For more information go to www.P65Warnings.ca.gov.
References
- electronics.us
- Warranty-registration - Group President Electronics USA
- P65Warnings.ca.gov
- Group President Electronics USA
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>