PRESIDENT ELECTRONICS 04395 Remote BT Mike Owner’s Manual
- May 15, 2024
- PRESIDENT ELECTRONICS
Table of Contents
REMOT BT MIKE
Owner’s Manual
04395 Remote BT Mike
Box Contents
STEERING WHEEL CONTROL INSTALLATION
- Wrap the bracket on the steering wheel (see fig. A1) in the position of your choice.
- Pull the strap around the steering wheel. Pull on the strap until the bracket can no longer be tumed.
- Attach the strap to the 2 small lugs (see fig. A2).
- Place the retainer on the lugs (see fig. A3 and A4).
- The steering wheel control bracket is fixed.
- Slide the control as shown in fig. A5.
REMOVING THE CONTROL FROM ITS BRACKET
- Using your fingemail, pull apart the retaining lug (see fig. A6 point 1).
- Remove the control unit (see fig. A6 point 2).
DONGLE INSTALLATION / REMOVAL
- Plug in / remove the dongle from your CB PRESIDENT as shown in fig. B1.
OPERATING YOUR REMOTE BT MIKE
Switch on your CB PRESIDENT.
The dongle LED flashes red once every 5 seconds.
Set switch [7] on the steering wheel control to |. “POWER ON” is announced.
“CONNECTED” is announced once the control is connected to the dongle.
The dongle LED flashes green once every 5 seconds. (otherwise see §5)
1.PTT (Push To Talk)
2. Channel selector down
3. Channel selector up
4. Control light
5. Microphone
6. USB port (Charging)
7. On/Off
8. Settings button| 
---|---
-
CHANNEL SELECTOR:
These keys [2] and [3] allow you to move up or down a channel.
You can reverse up/down to adapt it to the chosen position.
To do this, press and hold the button that will be assigned to down and start (switch on) the steering wheel control. -
PTT (Push To Talk):
The PTT button [1] on the steering wheel control can be set to 2 modes:
MODE 1 (default) : Press PTT [1] once to talk. Press a second time to receive a message
To activate this mode:
Press and hold buttons (2] and [1] for 2 seconds.
The red LED flashes 3 times and turns off. Mode 1 is active.
MODE 2: Press and hold to speak. Release to return to reception.
To activate this mode:
Press and hold buttons (3] and [1] for 2 seconds.
The green LED flashes 3 times and turns off. Mode 2 is active. -
NRC SETTING
Your REMOTE BT MIKE is equipped with NRC technology with 5 levels of adjustment.
To enter configuration mode:
– On the steering wheel control, press buttons [2] and [3] for 2 seconds.
– The current setting is displayed.
– Use button [2] or (3] to change the current setting.
– The current setting is saved.
– If no button is pressed for 10 seconds, you exit the parameter-setting mode. The current setting is saved. -
CHARGING
Plug one end of the USB cable into the connector [6] and the other into the USB port on your CB PRESIDENT, if fitted, or on your vehicle.
Steady red light [4]: charging.
Steady green light [4]: charging complete.
When the baitery is discharged, “DISCHARGED” /s announced every 5 minutes and the red LED flashes twice every 5 seconds. -
APPAIRING
The steering wheel control and dongle are supplied paired.
If you need to replace one of the two components, here’s how to pair them.
– Connect the dongle to your PRESIDENT transceiver.
– Press the button [8] briefly.
– The button will flash altemately red and green. The dongle is in pairing mode.
– Keep the control within 5m of the dongle.
– On the steering wheel control, press the PTT key [1]. LED [4] starts flashing red and green and “PAIRING” is announced. The control unit is in pairing mode.
– When pairing is complete, LED turns off. -
DELETING PAIRING
On the dongle: press button [8] for 8 seconds.
On the steering wheel control : Press buttons [1], [2] and [3] for 5 seconds. 3 rapid beeps are emitted. The control unit automatically switches to pairing mode.
6 – PIN MICROPHON PLUG
| 1 | Modulation |
|---|---|
| 2 | RX |
| 3 | TX – UP/DOWN |
| 4 | – |
| 5 | Ground |
| 6 | Power Supply |
BATTERY LOCATION
WARRANTY
(In accordance with the warranty conditions in the country of purchase)
Important: Proof of original purchase is required for warranty service.
WARRANTOR: GROUPE PRESIDENT ELECTRONICS (“PRESIDENT”) ELEMENTS OF WARRANTY:
PRESIDENT warrants, to the original user, if purchased from a retail store,
that this PRESIDENT product will be free from defects in materials and
craftsmanship, subject to the limitations and exclusions as set out below.
This warranty extends only to the original user. The warranty will be invalid
if the Product is (A) damaged or has not been maintained in good condition
through reasonable maintenance, (B) has been modified, altered or used as part
of any conversion kits, subassemblies, or any configurations not sold by
PRESIDENT, (C) improperly installed, (D) serviced or repaired by someone other
than an authorized PRESIDENT service center for a defect or malfunction
covered by this warranty, (E) used in any conjunction with equipment or parts
or as part of any system not manufactured by PRESIDENT, or (F) installed or
programmed by anyone other than as detailed by the owner’s manual for this
product.
STATEMENT OF REMEDY: In the event that the product does not conform to this
warranty at any time while this warranty is in effect, warrantor will either,
at its option, repair or replace the defective unit and return it to you
without charge for parts, service, or any other cost (except shipping and
handling) incurred by warrantor or its representatives in connection with the
performance of this warranty. Warrantor, at its option, may replace the unit
with a new or refurbished unit, THE LIMITED WARRANTY SET FORTH ABOVE IS THE
SOLE AND ENTIRE WARRANTY PERTAINING TO THE PRODUCT AND IS IN LIEU OF AND
EXCLUDES ALL OTHER WARRANTIES OF ANY NATURE WHATSOEVER, WHETHER EXPRESS,
IMPLIED OR ARISING BY OPERATION OF LAW, INCLUDING, BUT NOT LIMITED TO ANY
IMPLIED WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE.
THIS WARRANTY DOES NOT COVER OR PROVIDE FOR THE REIMBURSEMENT OR PAYMENT OF
INCIDENTAL OR CONSEQUENTIAL DAMAGES.
Some countries do not allow this exclusion or limitation of incidental or
consequential damages so the above limitation or exclusion may not apply to
you.
LEGAL REMEDIES: This warranty gives you specific legal rights, and you may
also have other rights which vary from country to country.
PROCEDURE FOR OBTAINING PERFORMANCE OF WARRANTY: If, after following the
instructions in the owner’s manual you are certain that the Product is
defective, pack the Product carefully (preferably in its original packaging).
The Product should include all parts and accessories originally packaged with
the Product. Include proof of original purchase and a note describing the
defect that has caused you to return it. The Product should be shipped freight
prepaid, by traceable means, to warrantor at:
Group PRESIDENT ELECTRONICS
1007 Collier Center Way,
Naples, Florida 34110
USA
Head Office France
BP 100- 34540 BALARUC
Tél : +33 (0)4.67.46.27.27 – Fax : +33 (0)4.67.48.48.4
Site Internet : http://www.president-electronics.com
E-mail : groupe@president-electronics.com
Head Office: USA – 1007 Collier Center Way,
Naples, Florida 34110
Web: http://Awww.president-electronics.us
Email : info@president-electronics.us
The declaration of conformity is available at the following internet address:
https://president-electronics.com/DC/ACFD602
BT MIKE
FCC ID: 2AEOCPC214
IC : 20240-PC214
BT DONGLE 5
FCC ID: 2AEOCPC215 Bs
IC : 20240-PC215 >
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>