VicTsing BH486A Mini WiFi Projector User Manual
- June 6, 2024
- VicTsing
Table of Contents
VicTsing BH486A Mini WiFi Projector
IMPORTANT SAFETY PRECAUTIONS
Important : In order to get the best viewing effact. it’s suggested that
you use the product in a dark room.
warning : Following safecy instructions can sustain product’s lifespan
and prevent it from firing or electric shock so please read them carefully and
pay attention to all warnings.
- Do not install it in a place with poor ventilation.
- Do not install it in a hot or damp place.
- Do not block its ventilation holes (Intake or Exhaust
- Do not install it in a dusty or smoky place.
- Do not install it near to the temperature/smoke sensor, since it might make the sensor fail to vvork
- Do not install it in a position directly blown by air condition, otherwise it might be malfunctioned because of the water & vapour condensation or high temperature.
Note : In order to maintain the performance and reliability of projector.
please leave at least 30 cm of space around the projector.
Note : The projector’s light is very bright so please do not look at it
directly or point its light to your eyes in case of causing visua
damage.
PACKING LIST
Note : Please check whether the accessories are complete after opening the package. If it’s not complete. please contact customer service for a replacement.
PRODUCT INTRODUCTION
Note : Due to the design improvement. the appearance/screen printing/characters of the re· mote control might be somewhat different from the real product please in kind prevail.
NOTES
- Be cautious when using the remote control. Do not drop it, trample on it, or spill any liquid into it’s body.
- Do not put the remote control near to any heat source.
- Do not expose the remote control under sunlight.
- Do not put the remote control in a damp place.
INSTALLATION AND DEBUGING
lnstn.ictions
Referential Projection Distance
Turn Off Safely
Press the switch button on operation panel or remote control. and tum off the
device according to the system prompts.
PRODUCT SPECIFICATIONS
- Product Name LCD Projector (Home Use)
- Product Size 200xl 50x70mm
- Display Screen LCD
- Light Source LED
- Focusing Method Manually Focus
- Keystone Correction Ma nua I ly Adjust(± 1 S”)
- Screen Ratio 4/16:9
- LED Lifespan 50000 hours
- Native Resolution 1280×720
- Input Resolution l 920xl 080/l 280×720
- Contrast Ratio 2000:1
- Input Ports AV/ 2xUSB/ HDMI/TF
- Projection Size 30-120 inch
- Speaker 403Wx2
- Total Power SSW
- Power Voltage ACl 10-240V/ 50-60Hz
PROJECTION SETTINGS (SCREEN-SHARING SETTINGS)
Phone Projection/Screen-sharing Settings
Android
- Turn on Wi-Fi on your Android device and connect it to the netvvork
- Enter into phone settings and select
“Screen-sharing·. click it and find the device to connect
Note : For different phone brands. the names of ·screen-sharing” are different
Huawei : Wireless Projection/Multi-screen Interaction
Xiaomi : Wireless Display
Sony : Screen Mirroring
Samsung : Screen Sharing/Screen Mirroring/ Allshare Cast Smart View
IOS
Wired Projection/Screen-sharing
- Connect projector to phone with the USB data cable.
- Select trust to allow this program to be used on your phone.
Wireless Projection/Screen-sharing
-
Connect iPhone/lPad to projector’s Wi-Fi. WiFi name: “PRQ1ECTOR-xxxxxx” WiFi Password: 12345678
-
Open phone’s browser and input ·1 92.168.49. l” . and select (WiFi AP}->(Scan) to connect your own Wi-Fi.
Note : This connection needs 3-5 minutes. -
Return to phone’s main interface. and find the device and connect it via the “AirPlay”.
MENU SETTING
Get the best vievving effect with the most appropriate settings. You could set some relative parameters according to following steps.
- Press the menu button on projector or remote control if you want to set.
- You could set the parameter of the “Picture· and ·sound·. Press”‘ v<> on operation panel and select the range you want to set
Note : When the projector is hung on the ceiling or in a system of rear projection, please change the projection mode.