victsing K573T Wireless Keyboard User Manual

victsing K573T Wireless Keyboard

Packing List

1. Keyboard xl
2.  USB Receiver xl (Stored in battery compartment)
3. User Manual xl
4. VIP Card xl
5. Instruction Card xl
6.  FAQ Card xl

Instructions

Initial Use

1. Place 2 AAA dry batteries into the keyboard with the correct polarity. Turn on the switch on the upper right corner of keyboard. and it is in the factory default 2.4G mode.
2. Take out the receiver of battery compartment and plug it into the USB port of computer. Wait for the computer to install the drive automatically, and you can use the product after that.

Mode Switch

BTl Mode

1. Short press BTl mode switch button and its indicator will flash slowly showing that the keyboard is in BTl mode.
2.  Long press BTl mode switch button for 3s and its indicator will flash quickly showing that the keyboard enters pairing state.
   Turn on the Bluetooth of your laptop. if your computer system is Win 7 or earlier, please select to connect “BT3.0 KB”. If your computer system is Win 8 or later, please select to connect “BTS.0 KB”.

BT2Mode
Refer to BTl connection instructions.

Diagram

1. Multi-mode Switch. The product supports and  connection.
   It can be connected with and control 3 devices. User can switch modes via the corresponding mode switch button to control the corresponding
   device.

2.  Triple Systems Compatibility. Keyboard functions varies with different systems. The product can be adjusted to correspondingly adapt iOS, Mac and Windows.

3. Integrated Holder. The top integrated holder can hold phone. tablet or other mobile devices easily. It can maintain an appropriate angle to make you easy to read when typing. (Support vertical placement of tablet up to l 0.5″)

4. Independent Multimedia Keys: Pause. stop, previous track. next track, mute, decrease volume, increase volume, power switch.

5.  Switch between F Keys and Multimedia Keys Fl -Fl 2 keys are default PC functions as below

| Fl| F2| F3| F4
---|---|---|---|---
Default Fune – tions| Fl| F2| F3| F4
FN Com – bination Functions|

Decrease Brightness

|

Increase Brightness

| Multi – screen Display|

Back

| FS| F6| F7| FS
Default Fune- tions| FS| F6| F7| FS
FN Com –

bination Functions

|

Search

|

No function

|

No function

|

No function

| F9| Fl O| Fl l| Fl2| Delete
Default Fune – tions| F9| Fl O| Fll| Fl2| Delete
FN Com – bination Functions| No

function

| No

function

| No

funct i on

| Switch Input MethocJ| Sleep

press FN+ ESC simultaneously to enter tablet mode, switch between the default function and FN combined function, and press again to restore.

Solution to Keyboard’s 2.4G mode connection issue

1.  Turn on the power switch and switch the keyboard to 2.4G mode.
2. Press Esc and + button for 3-5 seconds and release until the indicator of 2.4G mode flashe&
3.  Plug the receiver into the computer. It is successfully connected when the indicator of 2.4G mode stops flashing. It can work then.

Solution to keyboard’s BTl mode connection issue

1. Clear the Bluetooth connection list of computer.
2. Turn on the power switch and switch it to BTl mode.
3.  Long press the button of BTl mode for over 3s and release until its indicator light flashes.
4.  Turn on the Bluetooth of computer. If your computer system is Win 7 or earlier. please select to connect “BT3.0 KB”. If your com­puter system is Win 8 or later, please select to connect “BT5.0 KB”. The keyboard’s BTl mode can work after successful connection.

BT2Mode
Refer to BTl mode solutions.
Note
If the product is still unworkable after above solutions. you could repeat those steps for a few times. If your problem canl get solved yet. please contact our Customer Service for help (Email:· support@victsing.com).

FCC STATEMENT

Any Changes or modifications not expressly approved by the party responsible for compliance could void the users authority to operate the equipment.
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions,

1.  This device may not cause harmful interference. and
2. this device must accept any interference received, including interference that may cause undesired operation.

FCC Radiation Exposure Statement
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment

Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy, and if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.

However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause hannful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures.:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>