VicTsing PC304A Wireless Keyboard User Manual

VicTsing PC304A Wireless Keyboard

Packing List

1. Keyboard xl
2. USB Receiver xl (Stored in the battery compartment)
3. User Manual xl
4. VIP Card xl
5. Instruction Card xl
6. FAQ Card xl

Instructions

Initial Use

1. Place 2 AAA dry batteries into the keyboard with the correct polarity. Tum on the switch on the upper right corner of the key­board. and it is in the factory default 2.4G mode.
2. Take out the receiver of the battery compartment and plug it into the USB port of the computer. Wait for the computer to install the driver automatically. and you can use the product after that.

Mode Switch

BTl Mode

1. Short press the Bn mode switch button and its indicator will flash slow/ty showing that the keyboard is in Bn mode.
2. Long press the BTL mode switch button for 3s and its indicator will flash quickly showing that the keyboard enters a pairing state. Tum on the Bluetooth of your laptop. if your computer system is Win 7 or earlier. please select to connect ·BT3.0 KB”. If your computer system is Win 8 or later. please select to connect “BTS.O KB”.

BT2 Mode
Refer to BTL connection instructions.
Diagram

1. Multi-mode Switch. The product supports (3 E) and§ connec­ on. It can be connected with and control 3 devices. Users can switch modes via the corre­ spending mode switch button to control the corresponding device.
2. Triple Systems Compatibility. Keyboard functions vary with different systems. The product can be adjusted to correspond­ingly adapt iOS. Mac and Windows.
   • Press FN-Q to m,i.<c it adapts 10S system (iPod. iPhone).
   • Press FN,@ to make it adapt Mac system (Mac)
   •  Press FN@to make it adapt Windows system (Windows system computer or Android phone}
3. Integrated Holder: The top Integrated holder can hold the phone. tablet or other mobile devices easily. It can ma1nta1n an appro­priate angle to make it easy to read when typing. (Support vertical placement of tablet up to 1 0.5″)
4. Independent Multimedia Keys: Pause. stop. previous track. next track mute. decrease volume. increase volume. pov-,er switch.
5. Switch between F Kays and Multimedia Keys : Fl Fl 2 I <e’ys are default PC t\Jnc, ions as below

Switch between F Keys and Multimedia Keys
Fl ·Fl 2 keys are default PC functions as below

press FN+ ESC simultaneously to enter tablet mode. switch between the default function and FN combined function. and press again to restore
The solution to Keyboard’s 2.4C mode connection issue

1. Turn on the J)C)’,11,’er SW1tch and switch the keyboard to 2.4C mode.
2. Press E.sc and CI) button for 3-5 seconds and release until the indicator of 2.4G mode flashes.
3. Plug the receiver into the computer It is successfully connected when the indicator of 2.4G mode stops flashing. It can IM)rk then.

The solution to keyboard’s BTL mode connection issue

1. Clear the Bluetooth connection list of the computer.
2. Turn on the power switch and switch it to BTL mode.
3. Long press the button of BTL mode for over 3s and release it until its indicator light flashes.
4. Tum on the Bluetooth of the computer. If your computer system is Win 7 or earlier. please select to connect ·sT3.0 KB”. If your computer system is Win 8 or later. please select to connect “BTS.O KS-.The keyboard’s sn mode can IM)rk after a successful connection.

BT2 Mode
Refer to BTL mode solutions.

Note:
If the product is still only)rkable after the above solutions. you could repeat those steps a few times If your problem can’t get solved yet. please contact our Customer Service for help (email:support@victsing.com)..)

Warning:
Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
NOTE:
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:

1. This device may not cause harmful interference, and
2. this device must accept any interference received, including interference that may cause undesired operation.

FCC Statement:

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

RF exposure compliance statement:
This device has been evaluated to meet the general RF exposure requirement

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>