VictSing Multi Device Wireless Bluetooth Keyboard User Manual

VictSing Multi Device Wireless Bluetooth Keyboard

PACKING LIST

1. Keyboard x1
2. USB Receiver x1
3. Charging Cable x1
4. User Manual x1
5. VIP Card x1
6. Instruction Card x1
7. FAQ Card x 1

Instructions

Initial Use:

1. please charge the keyboard when you use it for the first time.
2. Turn on the switch on the upper right corner of keyboard, and it is in the factory default 2.4G mode.
3. Take out USB receiver and plug it into computer.
4. It’s workable after its driver is installed on computer automatically

Mode Switch

BTI Mode

1. Short press BT1 mode switch button and its indicator will flash slowly showing that the keyboard is in BT1 mode.
2. Long press BT1 mode switch button for 3s and its indicator will flash quickly showing that the keyboard enters pairing state Turn on the Bluetooth of your laptop. if your computer system is Win 7 or earlier, please select to connect “BT3.0 KB”. If your computer system is Win 8 or later, please select to connect BTSO KB.

BT2 Mode
Refer to BT1 connection instructions.

Diagram 1

1. Multi-mode Switch. The product supports and connection. It can be connected with and control 3 devices. User can switch modes via the corresponding mode switch button to control the corresponding device
2. Triple Systems Compatibility. Keyboard functions varies with different systems. The product can be adjusted to correspondingly adapt iOS, Mac and Windows.
3. Press FN+( to make it adapt IOS system (Pad, iPhone)
4. Press FN+) to make it adapt Mac system (Mac)
5. Press FN+ (B) to make it adapt Windows system (Windows system computer or Android phone)

Integrated Holder. The top integrated holder can hold phone. tablet or other mobile devices easily. It can maintain an appro- priate angle to make you easy to read when typing. (Support vertical placement of tablet up to 10.5) 4. Rechargeable Design. Built-in large capacity Lithium battery. it can be recharged via the attached charging cable. When the keyboard is in low battery level, its power indicator light will flash to prompt. Its power indicator light stays on when charging and turns off when

MULTIMEDIA SHORTCUTS

Solution to Keyboard’s 2.4G mode connection issue

1. Turn on the power switch and switch the keyboard to 24G mode
2. Press Esc and (button for 3-5 seconds and release until the indicator of 2.4G mode flashes
3. Plug the receiver into the computer. It is successfully connected when the indicator of 2.4G mode stops flashing. It can work then

Solution to keyboard’s BT1 mode connection issue
1. Clear the Bluetooth connection list of computer
2 Turn on the power switch and switch it to BT1 mode
3. Long press the button of BT1 mode for over 3s and release until its indicator light flashes
4. Turn on the Bluetooth of computer. If your computer system is Win 7 or earlier. please select to connect “BT30 KB”. If your com- puter system is Win 8 or later, please select to connect “BT50 KB The keyboard’s BT1 mode can work after successful connection.

BT2 Mode

Refer to BT1 mode solutions
Note
If the product is still unworkable after above solutions you could repeat those steps for a few times. If your problem can’t get solved yet, please contact our Customer Service for help (Email support@victsing.com)

Warning: Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

NOTE: This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

FCC Statement : This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

RF exposure compliance statement:
This device has been evaluated to meet the general RF exposure requirement

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>