SW-MOTECH FRS.08.112.10201 EVO Footrest Kit Instruction Manual
- June 3, 2024
- SW-MOTECH
Table of Contents
SW-MOTECH FRS.08.112.10201 EVO Footrest Kit
MOUNTING INSTRUCTIONS
- Thank you for choosing this premium product from SW-MOTECH. Please visit our webshop for additional information, such as application charts and PDF mounting instructions. Any other documents that may be required (e.g. ABE certifications), are also available for download at our webshop.
- Installation and / or maintenance of this product require good technical understanding! For your own safety SW-MOTECH recommends having installation and / or servicing carried out by a specialist workshop! SW-MOTECH assumes no liability for damage caused by improper installation and/ or maintenance work!
- Carefully follow all the directions given in the mounting instructions and pay attention to all relevant information in the vehicle manual during assembly. Nonconformance can lead to vehicle damage or even endanger the driver! These mounting instructions are written based on our current state of knowledge. Legal requirements for accuracy do not exist.
- This product was developed for vehicles in their factory setting. Compatibility with original accessory parts or other manufacturers” accessory parts is not guaranteed. Furthermore, BEFORE installing this product, make sure that all moving parts (e.g. the chain) are in the original state of maintenance. Installed accessories can change the driving behaviour and/ or stability of your vehicle.
GENERAL INFORMATION
- Observe the country-specific regulations concerning vehicle registration / operation as well as TUY regulations if applicable. If required, register installed parts in the vehicle documents through an appropriate inspection authority.
- PREPARATION: Read the mounting instructions carefully and make sure that all items of the parts list are included. Make sure that your vehicle is parked safely and cannot fall over. Turn off the engine and remove the ignition key. Let the motor / exhaust cool off if necessary. Disconnect the vehicle battery when working on the electrical system. Use appropriate tools. Have another person to help you.
- MOUNTING: All parts and connections removed from the vehicle must be reinstalled in accordance with the vehicle manufacturers· specifications or replaced by parts delivered by SW-MOTECH. Secure all threads, unless otherwise specified, with medium-strength liquid thread locker.
- Torque specifications undefined by SW-MOTE CH must be obtained from the vehicle manufacturer or by a specialist workshop!
- FUNCTION CHECK: After installation make sure that all parts and connections previously removed are properly replaced. Also make sure that no moving parts are obstructed and no function of the vehicle is hindered in any way. Cables and hoses must not rub and/ or be pinched. Before starting to ride, perform a comprehensive check of all functions. After the first 50 km and then at regular intervals, check the tightening torque of all screw connections and the proper fit of the product.
PRODUCT SPECIFIC INFORMATION
ATTENTION: Ground clearance can be reduced by this product! Special care should be taken when cornering at extreme lean angles!
ABOUT COMPANY
- SW-MOTECH GmbH & Co. KG
- Ernteweg 8/10
- 35282 Rauschenberg Germany
- Tel. I phone + 49 (0)6425 / 8168 -050
- Fax/ fax + 49 (0)6425 / 8168 -10
- info@sw-motech.com
- www.sw-motech.com
PART LIST
- All measurements in millimeters
- The second number indicates the total quantity of the part in the delivery
- No torque specifications: Use the torque defined by vehicle manufacturer! The standard torque in this table can be used as long as it is within the vehicle manufacturer’s specifications.
MOUNTING
NOTE: Schematic illustration; Appearance may vary.
NOTE: The installation is shown on the left side of the vehicle only.
Repeat the same procedure on the right side of the vehicle.
NOTE: Before removing the original footrest, make sure to note the order
and direction of the original fixing parts.
Remove the original footrest.
- Clean the footrest holder thoroughly.
- Apply some grease to the inside of the footrest holder and the original pin [Orig.I.
- Attach the hinge adapter [1] with the shown original parts [orig.] to the footrest mount.
ATTENTION: The bevelled surface of the hinge adapter (1 I must be faced upwards!
- Insert the positioning cone (3) onto the star-shaped cone of the hinge adapter [1]. The height of the EVo footrest l4) can be adjusted individual by the various mounting positions (see right detail drawingl.
ATTENTION: Make sure to align the positioning cones (3) synchronously on each side! For orientation use the markings on the hinge adapter (1) and the positioning cone (3) (see left detail drawing).
- Insert the EVO footrest [4] onto the positioning cone [3]. The inclination angle of the EVO footrest [4] can be adjusted individually by the toothing of the positioning cone [3] [not more than 18° ; see right detail drawing].
ATTENTION: Make sure to align the EVO footrests (4) synchronously on each side! For orientation use the markings on the positioning cone (3) (see left detail drawing).
-
Attach the EVO footrest [4] LOOSELY to the hinge adapter [1]. as shown in the drawing. Check the synchronously alignment once again and the ergonomics.
-
Then attache the EVO footrest [4] to the hinge adapter [1].
ATTENTION: Use medium-strength liquid thread locker! -
Tighten the screw as specified in the parts list.
-
NOTE: This step is optional.
-
Attach the rubber pad [8] to the EVO footrest [41. as shown in the drawing.
ATTENTION: Use medium-strength liquid thread locker! -
Tighten the screw as specified in the parts list.
MOUNTING INSTRUCTIONS
- Thank you for choosing this premium product from SW-MOTECH. Please visit our webshop for additional information, such as application charts and PDF mounting instructions. Any other documents that may be required (e.g. ABE certifications), are also available for download at our webshop.
- Installation and / or maintenance of this product require good technical understanding! For your own safety SW-MOTECH recommends having installation and / or servicing carried out by a specialist workshop! SW-MOTECH assumes no liability for damage caused by improper installation and/ or maintenance work!
- Carefully follow all the directions given in the mounting instructions and pay attention to all relevant information in the vehicle manual during assembly. Nonconformance can lead to vehicle damage or even endanger the driver! These mounting instructions are written based on our current state of knowledge. Legal requirements for accuracy do not exist.
- This product was developed for vehicles in their factory setting. Compatibility with original accessory parts or other manufacturers” accessory parts is not guaranteed. Furthermore, BEFORE installing this product, make sure that all moving parts (e.g. the chain) are in the original state of maintenance. Installed accessories can change the driving behaviour and / or stability of your vehicle.
GENERAL INFORMATION
- Observe the country-specific regulations concerning vehicle registration / operation as well as TUY regulations if applicable. If required, register installed parts in the vehicle documents through an appropriate inspection authority.
- PREPARATION: Read the mounting instructions carefully and make sure that all items of the parts list are included. Make sure that your vehicle is parked safely and cannot fall over. Turn off the engine and remove the ignition key. Let the motor / exhaust cool off if necessary. Disconnect the vehicle battery when working on the electrical system. Use appropriate tools. Have another person to help you.
- MOUNTING: All parts and connections removed from the vehicle must be reinstalled in accordance with the vehicle manufacturers· specifications or replaced by parts delivered by SW-MOTECH. Secure all threads, unless otherwise specified, with medium-strength liquid thread locker.
- Torque specifications undefined by SW-MOTE CH must be obtained from the vehicle manufacturer or by a specialist workshop!
- FUNCTION CHECK: After installation make sure that all parts and connections previously removed are properly replaced. Also make sure that no moving parts are obstructed and no function of the vehicle is hindered in any way. Cables and hoses must not rub and/ or be pinched. Before starting to ride, perform a comprehensive check of all functions. After the first 50 km and then at regular intervals, check the tightening torque of all screw connections and the proper fit of the product.
PRODUCT SPECIFIC INFORMATION
ATTENTION: Pay attention to the mounting instructions included with the EVO footrest kit!
PART LIST
Schritt
Step
| Nr.
No.
| Art. – Nr. / Bezeichnung •
Item No. / Description *
| Part| Anzahl ..
Quantity ..
| Nm …|
---|---|---|---|---|---|---
| 111| FRS.00.112.001| EVO Footrest| 212| |
(2)| FRS.00.112.002| Positioning Cone| 212| |
(3)| FRS.00.112.005| Mounting Plate| 212| |
| | | | |
(4)| FRS.00.112.900.01| Rubber Pad| 212| |
(5)| M5 x 12; DIN 933| Hexagon Screw; stainless steel| 212| 3,5|
(6)| d 5,3; DIN 9021| Washer; stainless steel| 212| |
| Re ge l gew in de / Coarse Thread 01 M4 I M5 I
M6 I MS I M10 I M12| | | Re ge l gew in de /
Coars e Thread 01 M4 I M5 I M6 I MS I
M10 I M12
Stahl; FK 8.8 / Steel; CL 8.8 Nm 2,8 5,5 9,6 23 46
79| Stahl;FK10.9/Steel;CL10.9Nm 4,1 8,1 14 34 67 115
- All measurements in millimeters
- The second number indicates the total quantity of the part in the delivery
- No torque specifications: Use the torque defined by vehicle manufacturer! The standard torque in this table can be used as long as it is within the vehicle manufacturer’s specifications.
ATTENTION: Pay attention to the mounting instructions included with the EVO footrest kit!
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>