SW-MOTECH GPT.05.440.60000-B Top Case System Instruction Manual
- June 3, 2024
- SW-MOTECH
Table of Contents
SW-MOTECH GPT.05.440.60000-B Top Case System
ADVENTURE-RACK
Thank you for choosing this premium product from SW-MOTECH. Please visit our webshop for additional information, such as application charts and PDF mounting instructions. Any other documents that may be required (e.g. ABE certifications), are also available for download at our webshop.
Installation and/or maintenance of this product require good technical understanding! For your own safety SW-MOTECH recommends having installation and/or servicing carried out by a specialist workshop! SW-MOTECH assumes no liability for damage caused by improper installation and/or maintenance work!
Carefully follow all the directions given in the mounting instructions and pay attention to all relevant information in the vehicle manual during assembly. Nonconformance can lead to vehicle damage or even endanger the driver! These mounting instructions are written based on our current state of knowledge. Legal requirements for accuracy do not exist.
This product was developed for vehicles in their factory setting. Compatibility with original accessory parts or other manufacturers’ accessory parts is not guaranteed. Furthermore, BEFORE installing this product, make sure that all moving parts (e.g. the chain) are in the original state of maintenance. Installed accessories can change the driving behaviour and/or stability of your vehicle.
GENERAL INFORMATION
Observe the country-specific regulations concerning vehicle registration/ operation as well as TUV regulations if applicable. If required, register installed parts in the vehicle documents through an appropriate inspection authority.
PREPARATION: Read the mounting instructions carefully and make sure that all items of the parts list are included. Make sure that your vehicle is parked safely and cannot fall over. Turn off the engine and remove the ignition key. Let the motor/exhaust cool off if necessary. Disconnect the vehicle battery when working on the electrical system. Use appropriate tools. Have another person to help you.
MOUNTING: All parts and connections removed from the vehicle must be
reinstalled in accordance with the vehicle manufacturers· specifications or
replaced by parts delivered by SW-MOTECH. Secure all threads, unless otherwise
specified, with medium-strength liquid thread locker.
Torque specifications undefined by SW-MOTE CH must be obtained from the
vehicle manufacturer or by a specialist workshop!
FUNCTION CHECK: After installation make sure that all parts and connections previously removed are properly replaced. Also make sure that no moving parts are obstructed and no function of the vehicle is hindered in any way. Cables and hoses must not rub and/or be pinched. Before starting to ride, perform a comprehensive check of all functions. After the first 50 km and then at regular intervals, check the tightening torque of all screw connections and the proper fit of the product.
PRODUCT SPECIFIC INFORMATION
ATTENTION: The indicated maximum load is inclusive the weight of topcase/luggage and adapter kit! The maximum vehicle load specified by the manufacturer must not be exceeded!
SW-MOTECH GmbH & Co. KG
Ernteweg 8/10
35282 Rauschenberg Germany
Tel./ phone+ 49 (0)6425 / 8168 – 050 Fax / fax+ 49 (0)6425 / 8168 – 10
info@sw-motech.com www.sw-motech.com
PARTS LIST
MOUNTING
Clean the surface of the mounting brackets [1 I and fixate the protection
stripes [2) on their underside, as shown in the left detail drawing.
Cut openings into the protection stripes [2) where the mounting points are now
covered.
Remove the shown parts from the lugagge carrier, as shown in the right
drawing.
Attach the mounting brackets [1) to the vehicle, as shown in the drawing.
ATTENTION: Use liquid thread locker for screw (3) !
Do not fully tighten the screws yet.
NOTE : Choose the marked front or rear mounting position according to your preferences.
Attach the luggage rack [8) to the mounting brackets [11. as shown in the
drawing.
Once all parts are evenly positioned without excess tension, tighten the
screws as specified in the parts list.
Adapter kit for ADVENTURE-RACK – Adapter plate for STREET-RACK
Thank you for choosing this premium product from SW-MOTECH. Please visit our webshop for additional information, such as application charts and PDF mounting instructions. Any other documents that may be required (e.g. ABE certifications), are also available for download at our webshop.
Installation and/or maintenance of this product require good technical understanding! For your own safety SW-MOTECH recommends having installation and/or servicing carried out by a specialist workshop! SW-MOTECH assumes no liability for damage caused by improper installation and/or maintenance work!
Carefully follow all the directions given in the mounting instructions and pay attention to all relevant information in the vehicle manual during assembly. Nonconformance can lead to vehicle damage or even endanger the driver! These mounting instructions are written based on our current state of knowledge. Legal requirements for accuracy do not exist.
This product was developed for vehicles in their factory setting. Compatibility with original accessory parts or other manufacturers’ accessory parts is not guaranteed. Furthermore, BEFORE installing this product, make sure that all moving parts (e.g. the chain) are in the original state of maintenance. Installed accessories can change the driving behaviour and/or stability of your vehicle.
GENERAL INFORMATION
Observe the country-specific regulations concerning vehicle registration/
operation as well as TUV regulations if applicable. If required, register
installed parts in the vehicle documents through an appropriate inspection
authority.
PREPARATION: Read the mounting instructions carefully and make sure that all items of the parts list are included. Make sure that your vehicle is parked safely and cannot fall over. Turn off the engine and remove the ignition key. Let the motor/exhaust cool off if necessary. Disconnect the vehicle battery when working on the electrical system. Use appropriate tools. Have another person to help you.
MOUNTING: All parts and connections removed from the vehicle must be
reinstalled in accordance with the vehicle manufacturers· specifications or
replaced by parts delivered by SW-MOTECH. Secure all threads, unless otherwise
specified, with medium-strength liquid thread locker.
Torque specifications undefined by SW-MOTE CH must be obtained from the
vehicle manufacturer or by a specialist workshop!
FUNCTION CHECK: After installation make sure that all parts and connections previously removed are properly replaced. Also make sure that no moving parts are obstructed and no function of the vehicle is hindered in any way. Cables and hoses must not rub and/or be pinched. Before starting to ride, perform a comprehensive check of all functions. After the first 50 km and then at regular intervals, check the tightening torque of all screw connections and the proper fit of the product.
ADVENTURE RACK
NOTE: BEFORE attaching the mounting bracket (1 ], insert the screws {]
supplied with the ADVENTURE-RACK into the rear openings. The screws {] can be
tightened after attaching the mounting plate through the cutouts.
Attach the mounting bracket [1 I to your ADVENTURE RACK [sold separately). as
shown in the drawing.
ATTENTION: Use liquid thread locker (screws (2) only)!
Tighten the screws as specified in the parts list.
URBAN ABS top case
Thank you for choosing this premium product from SW-MOTECH. Please visit our webshop for additional information, such as application charts and PDF mounting instructions. Any other documents that may be required (e.g. ABE certifications), are also available for download at our webshop.
Installation and/or maintenance of this product require good technical understanding! For your own safety SW-MOTECH recommends having installation and/or servicing carried out by a specialist workshop! SW-MOTECH assumes no liability for damage caused by improper installation and/or maintenance work!
Carefully follow all the directions given in the mounting instructions and pay attention to all relevant information in the vehicle manual during assembly. Nonconformance can lead to vehicle damage or even endanger the driver! These mounting instructions are written based on our current state of knowledge. Legal requirements for accuracy do not exist.
This product was developed for vehicles in their factory setting. Compatibility with original accessory parts or other manufacturers” accessory parts is not guaranteed. Furthermore, BEFORE installing this product, make sure that all moving parts (e.g. the chain) are in the original state of maintenance. Installed accessories can change the driving behaviour and/or stability of your vehicle.
GENERAL INFORMATION
Observe the country-specific regulations concerning vehicle registration /
operation as well as TUY regulations if applicable. If required, register
installed parts in the vehicle documents through an appropriate inspection
authority.
PREPARATION: Read the mounting instructions carefully and make sure that all items of the parts list are included. Make sure that your vehicle is parked safely and cannot fall over. Turn off the engine and remove the ignition key. Let the motor / exhaust cool off if necessary. Disconnect the vehicle battery when working on the electrical system. Use appropriate tools. Have another person to help you.
FUNCTION CHECK: This is a universal product. For this reason make sure BEFORE the first use, that the product can be fixed properly and used without problems with your vehicle type. After fixation also make sure that no moving parts are obstructed and the function of the vehicle is not hindered in any way. Lamps as taillight and turn signals must not be limited in their function. Cables and hoses must not rub and/or be pinched. Before starting to ride, perform a comprehensive check of all functions.
PRODUCT SPECIFIC INFORMATION
ATTENTION: Riding with this product may affect the motorcycles driving and
braking performance!
ATTENTION: Before riding and at each stop (every 200 km) check proper fixation
of the product!
ATTENTION: The maximum load of the used SW-MOTECH STREET-RACK / ADVENTURE-RACK must not be exceeded (refer mounting instructions of the rack)! The maximum vehicle load specified by the manufacturer must not be exceeded!
PARTS LIST
URBAN ABS top case for STREET-RACK
Step [1]: Open the lid and inner zipper of the top case (1].
Step [2]: Flip up the inner lining.
Step [3]: Attach the locking system (41 under the top case (1]. Pay attention
to the position of the locking lever (closed].
Tighten the screws as specified in the parts list.
Step [4]: Flip down the inner lining.
Step [5]: Close the inner zipper of the top case I 1).
Step [6]: Turn the locking button of the anti-theft device [8) to the closed
position.
Step [7]: Attach the anti-theft device [8) inside the top case [1). Tighten
the screws as specified in the parts list.
MOUNTING TO THE STREET-RACK
Step [8]: Turn the locking button into the open position.
Step [9]: Push the locking lever into the open position.
Step [1 D]: Slide the locking system [4) with the two hooks into the openings
of your STREET-RACK
[sold separately).
Step [11]: Press the top case [1) slightly down …
Step [12]: … and close the locking lever. Pay attention to the audible snap
sound.
Step [13]: Secure the top case via locking button of the anti-theft device [8)
against theft and check the proper fit on the vehicle.
TIP: We recommend leaving the locking button of the anti-theft device [8) in
the closed position during the ride.
URBAN ABS top case as lashing variation
Step [1]: Open the lid and inner zipper of the top case 111.
Step [2]: Flip up the inner lining.
Step [3]: Attach the foam rubber base 14) under the top case 11]. Tighten the
screws as specified in the parts list.
Step [4]: Flip down the inner lining.
Step [5]: Close the inner zipper of the top case I 1 J.
Step [6]: Attach the cover plate (7) inside the top case (11.
Tighten the screws as specified in the parts list.
FIXATION TO THE VEHICLE
Step [7]: On both sides entangle TWO loop straps (11 I to appropriate and
reliable attachment points in the rear area of the vehicle (e.g. luggage hook
etc.I.
Then entangle on both sides TWO loop straps (11 I to appropriate and reliable
attachment points of the vehicle (e.g. vehicles frame, footrest mounts etc.).
FUNCTION CHECK
(MUST BE OBSERVED)
ATTENTION: All loop straps must not contact any hot or moving parts of the
vehicle. All loop straps should also remain 15 cm away from hot parts of the
vehicle and remain clear of the exhaust stream. For this reason compress the
suspension fully several times with your vehicle stationary.
Step [8]: Attach the hook buckles of the loop straps [11 I on both sides
to the marked loops of the top case
[1 I. as shown in the drawing. Tighten all loop straps until the top case [1)
is centered and securely fastened to the vehicle.
Step [9]: Secure the overlength of the loop straps [6) with the rubber loops
against flapping.
Step [10]: Check the proper fit of the top case.
MOISTURE PROTECTION
Use the included waterproof inner bag [2) to protect your luggage from
moisture.
LOADING
ATTENTION: Never store pointy or sharp-edged objects, which could cause
injury to persons or damage to the vehicle/top case.
Volume expansion: Open the revolving zipper. For a tight fit the opening
angle can be adjusted via the attached straps.
CARE
For cleaning use ONLY a soft textile brush, cloth or sponge and warm soapy
water! Rinse with clean water.
Do NOT use strong cleaning agents, rough cleaning tools or high pressure
washer!
Clean the top case after riding in salty conditions, to avoid damage from
salt.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>