SW-MOTECH SCT.06.174.20001 Protection Set Instruction Manual

SCT.06.174.20001 Protection Set
Instruction Manual
KRS.00.169.10000/S
SCT.06.642.10000/B
STP.06.506.10000

MOUNTING INSTRUCTIONS

Header Pipe Protection

Thank you for choosing this premium product from SW-MOTECH. Please visit our webshop for additional information, such as application charts and PDF mounting instructions. Any other documents that may be required (e.g. ABE certifications), are also available for download at our webshop. » www.sw- motech.com
Installation and/or maintenance of this product require good technical understanding. For your own safety SW-MOTECH recommends having installation and/or servicing carried out by a specialist workshop. SW-MOTECH assumes no liability for damage caused by improper installation and/or maintenance work.
Carefully follow all the directions given in the mounting instructions. Also pay attention to all relevant information in the vehicle manual during assembly. Nonconformance can lead to vehicle damage or even endanger the driver! Please keep the mounting instructions as reference.
This product was developed for vehicles in their original condition. Compatibility with original accessory parts or other manufacturers’ accessory parts is not guaranteed. Installed accessories can change driving behaviour and/or stability of your vehicle.

GENERAL INFORMATION

Please observe any country-specific regulations concerning vehicle registration or operation as well as TUV regulations where applicable. If required, register installed parts in the vehicle documents together with the appropriate inspection authority.
PREPARATION: Read the mounting instructions carefully and make sure that all parts are included. Make sure that your vehicle is parked safely and cannot fall over. Turn off the engine and remove the ignition key. Let the motor/exhaust cool off if necessary. Disconnect the vehicle battery when working on the electrical system. Make sure to use only the appropriate tools. During installation have another person help you.
MOUNTING: All parts and connections removed from the vehicle must be reinstalled in accordance with the vehicle manufacturer specifications or replaced by parts and hardware delivered by SW-MOTECH. Secure all threads, unless otherwise specified, with medium-strong strength liquid thread locker. If not otherwise defined by the vehicle manufacturer or SW-MOTECH, screws and nuts must be tightened according to DIN/ISO specifications. After installation make sure that all parts and hardware previously removed are properly replaced.
FUNCTION CHECK: After installation also make sure that no moving parts are obstructed and function of the vehicle is not hindered in any way. Cables and hoses must not rub and/or be pinched. Before starting to ride, perform a comprehensive check of all functions. Regularly check [every 100 km] for the proper seating of all parts and connections removed during installation.

PARTS LIST

Step| No.| Item No./ Description| Part| **Quantity*| N-m**
---|---|---|---|---|---
1| | KRS.00.169.10000/S| Head Pipe Protection| |
| (1)| KRS.00.169.001| Head Pipe Protection|  1 /1|
(2)| SS.A2.032.050.01| Hose Clamp (0 32 – 50 mm)|  2 /2|
| | | |
| KRS.00.169.10100A| Head Pipe Protection| |
(1)| KRS.00.169.001| Head Pipe Protection|  1 /1|
(2)| SS.A2.050.070.01| Hose Clamp (0 50 – 70 mm)|  2 /2|

All measurements in millimeters

MOUNTING

ATTENTION: Let the motor/exhaust cool off bevore proceeding with the assembly. Danger of burns!
NOTE: To improve the fitting of the header pipe protection In, you can cut the two outer elements. Clean the surface of the header pipe from dirt and mount the header pipe protection (1) with the hose clamps (2).
Make sure no hoses or cables are pinched.
Frame Cover
Thank you for choosing this premium product from SW-MOTECH.  Please visit our webshop for additional information, such as application charts and PDF mounting instructions. Any other documents that may be required (e.g. ABE certifications), are also available for download at our webshop. » www.sw- motech.com
Installation and/or maintenance of this product require good technical understanding. For your own safety SW-MOTECH recommends having installation and/or servicing carried out by a specialist workshop. SW-MOTECH assumes no liability for damage caused by improper installation and/or maintenance work.
Carefully follow all the directions given in the mounting instructions. Also pay attention to all relevant information in the vehicle manual during assembly. Nonconformance can lead to vehicle damage or even endanger the driver! Please keep the mounting instructions as reference.
This product was developed for vehicles in their original condition. Compatibility with original accessory parts or other manufacturers’ accessory parts is not guaranteed. Installed accessories can change driving behaviour and/or stability of your vehicle.
GENERAL INFORMATION
Please observe any country-specific regulations concerning vehicle registration or operation as well as TUV regulations where applicable. If required, register nstalled parts in the vehicle documents together with the appropriate inspection authority.
PREPARATION: Read the mounting instructions carefully and make sure that all parts are included. Make sure that your vehicle is parked safely and cannot fall over. Turn off the engine and remove the ignition key. Let the motor/exhaust cool off if necessary. Disconnect the vehicle battery when working on the electrical system. Make sure to use only the appropriate tools. During nstallation have another person help you.
MOUNTING: All parts and connections removed from the vehicle must be reinstalled in accordance with the vehicle manufacturer specifications or replaced by parts and hardware delivered by SW-MOTECH. Secure all threads, unless otherwise specified, with medium-strong strength liquid thread locker. f not otherwise defined by the vehicle manufacturer or SW-MOTECH, screws and nuts must be tightened according to DIN/ISO specifications. After installation make sure that all parts and hardware previously removed are properly replaced.
FUNCTION CHECK: After installation also make sure that no moving parts are obstructed and function of the vehicle is not hindered in any way. Cables and hoses must not rub and/or be pinched. Before starting to ride, perform a comprehensive check of all functions. Regularly check [every 100 km] for the proper seating of all parts and connections removed during installation.

Step| No.| Item No. / Description| Par Part| Quantity| N-m
---|---|---|---|---|---
2| (1)| SCT.06.642.002| Cover Plate| 1 /1|
| (2)| M6 x 35; ISO 7380| Lenshead Screw; black| 1 /1| 9,6
| (3)| 14/6,2/4| Spacer| 1 /1|
(4)| 17/8,4/2| Spacer; black| 1 /1|
| | | | |
4| (5)| SCT.06.642.900| Cover Plate| 1 /1|
| (6)| 20 / 10,5 / 3| Spacer| 1 /1|

All measurements in millimeters.

MOUNTING

Remove the passenger footrest, the screws and the washer, as shown in the drawing.

Attach the cover plate (1) with the original screws (Orig.) to the vehicle, as shown in the drawing.
ATTENTION: Use liquid thread locker! Tighten the original screws (Orig.) with the manufacturer’s specified torque.
Tighten the screw (2) as specified in the parts list.

Remove the passenger footrest, the screws and the washer, as shown in the drawing.

Attach the cover plate (5) with the original screws (Orig.) to the vehicle, as shown in the drawing.
ATTENTION: Use liquid thread locker!
Tighten the original screws (Orig.) with the manufacturer’s specified torque.
MOUNTING INSTRUCTIONS
Alternator cover guard
Thank you for choosing this premium product from SW-MOTECH. Please visit our webshop for additional information, such as application charts and PDF mounting instructions. Any other documents that may be required (e.g. ABE certifications), are also available for download at our webshop. Installation and/or maintenance of this product require good technical understanding! For your own safety SW-MOTECH recommends having installation and/or servicing carried out by a specialist workshop!
SW-MOTECH assumes no liability for damage caused by improper installation and/or maintenance work!
Carefully follow all the directions given in the mounting instructions and pay attention to all relevant information in the vehicle manual during assembly. Nonconformance can lead to vehicle damage or even endanger the driver! These mounting instructions are written based on our current state of knowledge. Legal requirements for accuracy do not exist.
This product was developed for vehicles in their factory setting. Compatibility with original accessory parts or other manufacturers’ accessory parts is not guaranteed. Furthermore, BEFORE installing this product, make sure that all moving parts (e.g. the chain) are in the original state of maintenance. Installed accessories can change the driving behaviour and/or stability of your vehicle.
GENERAL INFORMATION
Observe the country-specific regulations concerning vehicle registration/ operation as well as TUV regulations if applicable. If required, register installed parts in the vehicle documents through an appropriate inspection authority.
PREPARATION: Read the mounting instructions carefully and make sure that all items of the parts list are included. Make sure that your vehicle is parked safely and cannot fall over. Turn off the engine and remove the ignition key. Let the motor/exhaust cool off if necessary. Disconnect the vehicle battery when working on the electrical system. Use appropriate tools. Have another person to help you.
MOUNTING: All parts and connections removed from the vehicle must be reinstalled in accordance with the vehicle manufacturers· specifications or replaced by parts delivered by SW-MOTECH. Secure all threads, unless otherwise specified, with medium-strength liquid thread locker.
Torque specifications undefined by SW-MOTECH must be obtained from the vehicle manufacturer or by a specialist workshop!
FUNCTION CHECK: After installation make sure that all parts and connections previously removed are properly replaced. Also make sure that no moving parts are obstructed and no function of the vehicle is hindered in any way. Cables and hoses must not rub and/or be pinched. Before starting to ride, perform a comprehensive check of all functions. After the first 50 km and then at regular intervals, check the tightening torque of all screw connections and the proper fit of the product.
PARTS LIST

Step| No.| Item No. / Description a| Part| N-Mc|
---|---|---|---|---|---
1| (1)| STP.06.506.001| Mounting Bracket| 1/1|
| (2)| STP.00.510.001| Middle Part| 1 /1|
(3)| STP.00.510.002| Top Part| 1 /1|
(4)| STP.00.510.003| Lower Part| 1 /1|
(5)| STP.00.510.004| Logo Washer| 1/1|
(6)| M10 x 20; DIN 7991| Countersunk Screw| 1/1| 8
(7)| M10; DIN 985| Lock Nut| 1/1|
| | | |
3| (8)| M6 x 60; ISO 7380| Lensehead Screw; black| 1 /1| OEM
| (9)| 0 12 /0 6,4 /h 30| Spacer; black| 1 /1|
8.8|  Coarse Thread ∅| M4|  M5| M6| M8| M10| M12
---|---|---|---|---|---|---|---
Steel. CL 8.8 N-m| 2,8| 5,5| 9,6| 23| 46| 79
10.9| Coarse Thread ∅|  M4|  M5| M6| M8| M10| M12
Stahl FK 10.9 / Steel CL 10.9 N-m| 4,1| 18,1| 14| 34| 67| 115

Note.All measurements in millimeters. The second number indicates the total quantity of the part in the delivery torquspifictions Use the torque defined by vehicle manufacturer The standard torque in this table can be4seal0gag itis within the vehicle mufacturerg Specification

Attach the parts (2) to (5) to the mounting bracket (1), as shown in the drawing.
ATTENTION: Use liquid thread locker!
Tighten the screw (6) as specified.

Remove the marked screws from the wehicle

Attach the mounting bracket (1) to the vehicle, as shown in the drawing.
ATTENTION: Use liquid thread locker!
Tighten the screw (8) and the original screws (Orig.) with the manufacturers’ specified torque.

SW-MOTECH GmbH & Co. KG
Ernteweg 8/10
35282 Rauschenberg
Germany
Tel. / phone + 49 (0)6425 / 8168 – 050
Fax / fax + 49 (0)6425 / 8168 – 10
info@sw-motech.com
www.sw-motech.com
Errors and omissions excepted.
Technical and design modifications are subject to change.

Documents / Resources

| SW- MOTECH SCT.06.174.20001 Protection Set [pdf] Instruction Manual
SCT.06.174.20001 Protection Set, SCT.06.174.20001, Protection Set
---|---

References

• Modesto Technologies

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>