SW-MOTECH KFT.22.114.50103-B Side Case Instruction Manual

KFT.22.114.50103-B Side Case
Instruction Manual

MOUNTING INSTRUCTIONS

PRO side carriers
 Thank you for choosing this premium product from SW-MOTECH. Please visit our webshop for additional information, such as application charts and PDF mounting instructions. Any other documents that may be required (e.g. ABE certifications), are also available for download at our webshop.
Installation and/or maintenance of this product require good technical understanding! For your own safety SW-MOTECH recommends having installation and/or servicing carried out by a specialist workshop! SW-MOTECH assumes no liability for damage caused by improper installation and/or maintenance work!
Carefully follow all the directions given in the mounting instructions and pay attention to an relevant information in the vehicle manual during assembly. Nonconformance can lead to vehicle damage or even endanger the driver! These mounting instructions are written based on our current state of knowledge. Legal requirements for accuracy do not exist.
This product was developed for vehicles in their factory setting. Compatibility with original accessory parts or other manufacturers’ accessory parts is not guaranteed. Furthermore, BEFORE installing this product, make sure that all moving parts (e.g. the chain) are in the original state of maintenance. Installed accessories can change the driving behaviour and/or stability of your vehicle.

GENERAL INFORMATION
Observe the country-specific regulations concerning vehicle registration/ operation as well as TUV regulations if applicable. If required, register installed parts in the vehicle documents through an appropriate inspection authority.
PREPARATION: Read the mounting instructions carefully and make sure that all items of the parts list are included. Make sure that your vehicle is parked safely and cannot fall over. Turn off the engine and remove the ignition key. Let the motor/exhaust cool off if necessary. Disconnect the vehicle battery when working on the electrical system. Use appropriate tools. Have another person to help you.
MOUNTING: All parts and connections removed from the vehicle must be reinstalled in accordance with the vehicle manufacturers’ specifications or replaced by parts delivered by SW-MOTECH. Secure all threads, unless otherwise specified, with medium-strength liquid thread locker. Torque specifications undefined by SW-MOTECH must be obtained from the vehicle manufacturer or by a specialist workshop!
FUNCTION CHECK: After installation make sure that all parts and connections previously removed are properly replaced. Also make sure that no moving parts are obstructed and no function of the vehicle is hindered in any way. Cables and hoses must not rub and/or be pinched. Before starting to ride, perform a comprehensive check of all functions. After the first 50 km and then at regular intervals, check the tightening torque of all screw connections and the proper fit of the product.

PRODUCT SPECIFIC INFORMATION

ATTENTION: The indicated maximum load is inclusive the weight o case/luggage and adapter kit! The maximum vehicle load specified by the manufacturer must not be exceeded! The side carriers are designed exclusively for the use of SW-MOTECH adapter kits. Dismount the side carriers when travelling without cases/luggage. Always use the side carriers in pairs.
ATTENTION: Make sure that after attaching the luggage to the vehicle it is not in the exhaust flow! Dangers of burns!

PARTS LIST

| No.| Item No. / ascription| Part| Anzall Oinntity –|
---|---|---|---|---|---
1| (1)| KFT.22.892.003| Crossbar| 1 ti|
(2)| M6 x 35; DIN 912| Hexagon Socket Screw| 2/2| 8
(3)| o 6,4; DIN 9021| Washer| 2 /2|
(4)| 014/08,2/h 8| Spacer| 2 /2|
(5)| 0 15/0 6,4 /h 20| Spacer| 2/2|
(6)| KFT.22.892.002L| Mounting Tab; [eft| 1//|
(7)| M6 x 25; DIN 912| Hexagon Socket Screw| 2 /2| 8
(8)| 0 6,4; DIN 125| Washer| 2 /2|
(9)| 0 14 /0 6,2 /h 5| Spacer| 212|
(10)| KFT.22.892.001| Mounting Tab| 1 /7|
(11)| M8 x 55; DIN 912| Hexagon Socket Screw| 1/1| 20
(12)| 08,4; DIN 125| Washer| |
(13)| 013/08,4/h 13| Spacer; black| 1/1|
| | | |
2| (14)| KFT.22.892.002R| Mounting Tab; right| 1/1|
(15)| M6 x 65; DIN 912| Hexagon Socket Screw| 2 /2| 8
(16)| 06,4; DIN 125| Washer
(17)| 018/06,4/h 45| Spacer; black| 2 /2|
(18)| KFT.22.892.001| Mounting Tab| 1 /2|
[19)| M8 x 40; DIN 912| Hexagon Socket Screw| 2 /2| 20
(20)| 0 18/08,4/h 5| Spacer| 1/1|
(21)| M8 x 45; DIN 912| Hexagon Socket Screw| 1/1| 20
(22)| 030/o 8,4/h 5| Spacer| 1/1|
8.8| Coarse Thread θ| M4| M5| M6| M8| M10| M12
---|---|---|---|---|---|---|---
  Steel CL 8.8N-m|   2.8|   5.5|   9.6|   23|   46|   79
10.9| Coarse Threadθ| M4| M5| M6| M8| M10| M12
---|---|---|---|---|---|---|---
Steel CL 10.9 N.m)|   4.1|  4.1|  8.1|  34|  67|  115

PARTS LIST

• All measurements i n millimeters.
  – ** The second number indicates the total quantity of the part in the delivery.
  *** No torque specifications: Use the torque defined by vehicle manufacturer! The standard torque in this table can be used as long a siti s within the vehicle manufacturer’s specifications.

MOUNTING

Attach the crossbar (1) to the vehicle, as shown in the drawing.
ATTENTION: For models from 2017 onwards use spacer (5) instead of (41.
ATTENTION: Use liquid thread locker! Do not fully tighten the screws yet. Remove the shown plastic caps and screw from the left passenger footrest. Attach the mounting lugs (bland (101 to the passenger footrest, as shown in the drawing.
ATTENTION: Use liquid thread locker! Do not fully tighten the screws yet.

Remove the shown plastic caps and screws from the right passenger footrest and the exhaust mount. Attach the mounting lugs (141 and (18) to and behind the passenger footrest, as shown in the drawing.
ATTENTION: Use liquid thread locker! Do not fully tighten the screws yet.

Remove the license plate mount. Attach the crossbar (23) between mudguard and license plate mount, as shown in the drawing.
ATTENTION: Use liquid thread locker! Do not fully tighten the screws yet.

Attach the heat protection plate (271 with the parts of your adapter kit to the side carrier (26), as shown in the detail drawing (example drawing; the parts vary depending on the adapter kith.
ATTENTION: Use liquid thread locker!

ATTENTION: Dismount the sid e carriers (26) when travelling without sidecases!
Use the fasteners [29] to connect the side carriers (26) to the crossbars and mounting lugs. Secure the fasteners with the lock washers. Once all the parts are evenly positioned without excess tension , tighten the screws as specified.
NOTE: The Anti-Theft Device is sold separately.

Adapter kit for PRO side carrier – TRAX ADV/ION/EVO
Thank you for choosing this premium product from SW-MOTECH. Please visit our webshop for additional information, such as application charts and PDF mounting instructions. Any other documents that may be required (e.g. ABE certifications), are also available for download at our webshop.
Installation and/or maintenance of this product require good technical understanding! For your own safety SW-MOTECH recommends having installation and/or servicing carried out by a specialist workshop! SW-MOTECH assumes no liability for damage caused by improper installation and/or maintenance work!
Carefully follow all the directions given in the mounting instructions and pay attention to all relevant information in the vehicle manual during assembly. Nonconformance can lead to vehicle damage or even endanger the driver! These mounting instructions are written based on our current state of knowledge. Legal requirements for accuracy do not exist.
This product was developed for vehicles in their factory setting. Compatibility with original accessory parts or other manufacturers’ accessory parts is not guaranteed. Furthermore, BEFORE installing this product, make sure that all moving parts (e.g. the chain) are in the original state of maintenance. Installed accessories can change the driving behaviour and/or stability of your vehicle.

GENERAL INFORMATION
Observe the country-specific regulations concerning vehicle registration/ operation as well as TUV regulations if applicable. If required, register installed parts in the vehicle documents through an appropriate inspection authority. PREPARATION: Read the mounting instructions carefully and make sure that all items of the parts list are included. Make sure that your vehicle is parked safely and cannot fall over. Turn off the engine and remove the ignition key. Let the motor/exhaust cool off if necessary. Disconnect the vehicle battery when working on the electrical system. Use appropriate tools. Have another person to help you.
MOUNTING: All parts and connections removed from the vehicle must be reinstalled in accordance with the vehicle manufacturers’ specifications or replaced by parts delivered by SW-MOTECH. Secure all threads, unless otherwise specified, with medium-strength liquid thread locker. Torque specifications undefined by SW-MOTECH must be obtained from the vehicle manufacturer or by a specialist workshop!
FUNCTION CHECK: After installation make sure that all parts and connections previously removed are properly replaced. Also make sure that no moving parts are obstructed and no function of the vehicle is hindered in any way. Cables and hoses must not rub and/or be pinched. Before starting to ride, perform a comprehensive check of all functions. After the first 50 km and then at regular intervals, check the tightening torque of all screw connections and the proper fit of the product.

• All measurements in millimeters.
  ** The second number indicates the total quantity of the part i n the delivery.
  * No torque specifications:** Use the torque defined by vehicle manufacturer! The standard torque in this table can be used as long as it is within the vehicle manufacturer’s specifications.

MOUNTING

NOTE: The illustration shows the mounting t o the right PRO side carrier. Mount the parts to the left PRO side carrier in the same way as to the right PRO side carrier. Attach the shown parts to your PRO side carriers [sold separately). Tighten the screws as specified in the parts list .
ATTENTION: To ensure the proper fit of your TRAXADV/EVO/ION side case, adjust the latch hook (1) over the elongated holes ( see detail drawing)! Make sure that the side case’s latch engages properly when mounted!

MOUNTING INSTRUCTIONS
TRAX ION M/L TRAX ION top case
Thank you for choosing this premium product from SW-MOTECH. Please visit our webshop for additional information, such as application charts and PDF mounting instructions. Any other documents that may be required (e.g. ABE certifications), are also available for download at our webshop.
Installation and / or maintenance of this product require good technical understanding! For your own safety SW-MOTECH recommends having installation and / or servicing carried out by a specialist workshop! SW-MOTECH assumes no liability for damage caused by improper installation and/or maintenance work! Carefully follow all the directions given in the mounting instructions and pay attention to all relevant information in the vehicle manual during assembly. Nonconformance can lead to vehicle damage or even endanger the driver! These mounting instructions are written based on our current state of knowledge. Legal requirements for accuracy do not exist.
This product was developed for vehicles in their factory setting. Compatibility with original accessory parts or other manufacturers’ accessory parts is not guaranteed. Furthermore, BEFORE installing this product, make sure that all moving parts (e.g. the chain) are in the original state of maintenance. Installed accessories can change the driving behaviour and / or stability of your vehicle.

GENERAL INFORMATION
Observe the country-specific regulations concerning vehicle registration/operation as well as TUV regulations if applicable. If required, register installed parts in the vehicle documents through an appropriate inspection authority.
PREPARATION: Read the mounting instructions carefully and make sure that all items of the parts list are included. Make sure that your vehicle is parked safely and cannot fall over. Turn off the engine and remove the ignition key. Let the motor/exhaust cool off if necessary. Disconnect the vehicle battery when working on the electrical system. Use appropriate tools. Have another person to help you.
MOUNTING: All parts and connections removed from the vehicle must be reinstalled in accordance with the vehicle manufacturers’ specifications or replaced by parts delivered by SW-MOTECH. Secure all threads, unless otherwise specified, with medium-strength liquid thread locker. Torque specifications undefined by SW-MOTECH must be obtained from the vehicle manufacturer or by a specialist workshop!
FUNCTION CHECK: After installation make sure that all parts and connections previously removed are properly replaced. Also make sure that no moving parts are obstructed and no function of the vehicle is hindered in any way. Cables and hoses must not rub and / or be pinched. Before starting to ride, perform a comprehensive check of all functions. After the first 50 km and then at regular intervals, check the tightening torque of all screw connections and the proper fit of the product.

PRODUCT SPECIFIC INFORMATION
The TRAX ION aluminum case is designed exclusively for mounting on carrier systems by SW-MOTECH. Modifications made to the cases will void any warranty. ATTENTION: Riding with TRAX ION aluminum case may affect the motorcycle’s driving and braking performance.
ATTENTION: TRAX ION M / L must be used in pairs. Make sure the weight is evenly distributed between left and right side case.
ATTENTION: Maximum load: Please refer to the mounting instructions of the used carrier system by SW-MOTECH. Maximum speed with mounted TRAX ION aluminum case: 130 km/h (80 mph).
Date o f packaging:…..
Packed by:…………..

PARTS LIST

Step| No.| Item No./Description*| Part| Quantity| *Nm.
---|---|---|---|---|---
| (1)| | TRAX ION M| 1/t|
| ALK.00.165.11001118| TRAX ION M; left; black| |
| ALK.00.165.11001US| TRAX ION 14; left; silver| |
| ALK00.165.11001R/B| TRAX ION 14; right; black| |
| ALK.00.165.11001R/S| TRAX ION 14; right; silver| |
| | | |
(2)| | TRAX ION L| 1/1|
| ALK.00.165.10001118| TRAX ION L; left; black| |
| ALK.00.165.10001US| TRAX ION L; left; silver| |
| ALK.00.165.10001R/8| TRAX ION L; right; black| |
| ALK.00.165.10001RIS| TRAX ION L; right; silver| |
| | | |
(3)| | TRAX ION Top Case| 1 ii|
| ALK.00.165.15001/8| TRAX ION Top Case; black| |
| ALK00.165.15001/S| TRAX ION Top Case; silver| |
8.8| Coarse Thread θ| M4| M5| M6| M8| M10| M12
---|---|---|---|---|---|---|---
  Steel CL 8.8N.m|   2.8|   5.5|   9.6|   23|   46|   79
10.9| Coarse ThreadΦ| M4| M5| M6| M8| M10| M12
---|---|---|---|---|---|---|---
Steel CL 10.9N.m)|   2.8|  5.5| 9.6| 23| 46| 79

• All measurements i n millimeters.
  – ** The second number indicates the total quantity of the part i n the delivery.
  *** No torque specifications: Use the torque defined by vehicle manufacturer! The standard torque in this table can b e used as long a sitis within the vehicle manufacturer’s specifications.

CARE
To clean the TRAX ION aluminum case, use warm, Soapy water and a soft, clean cloth. Rinse with clean water. Do NOT use strong cleaning agents, rough cleaning tools or  igh pressure washer!
ATTENTION: The inner surface o f the silver TRAXION aluminum cases is not sealed. Abrasion with aluminum can cause a grey film to  accumulate on case contents. To avoid this problem, we recommend TRAX inner bags [sold separately).
MOUNTING

Attach the SW-MOTECH adapter solution for TRAX (sold separately) to your SW- MOTECH side carrier.  Fixthe TRAX ION M/L with all four fixing lugs as shown. ush the TRAX ION M/L downward until it is fixed  in position.
Clamp the TRAX ION M/L latch to the latch hook as shown.
ATTENTION: It is very important to have proper clamping force with the latches. I f the latch is too loose,  adjust the position o f the latch hook to attain the proper  ension.  Always lock the latches before riding with TRAX lock set (sold separately).

ATTENTION
Make sure that the TRAX ION M/L is properly attached t o the  SW-MOTECH adapter solution for TRAX and fully engaged to all four mounting points! ALL latches of   he TRAX IONM/L must be locked BEFORE riding with the TRAX lock set (sold separately) and remain closed while riding.  Improperly mounted cases run therisk of detaching during transport.

 Attach the suitable SW-MOTECH adapter adapter solution for TRAX (sold separately] on top of your SW-MOTECH luggage carrier.
Fix the TRAX ION top case with all four fixing lugs on the bottom side as shown. Slide the TRAX ION top case forward until it’s fixed in position. Clamp the TRAX ION top case latch to the latch hook as shown.
ATTENTION: It is very important to have proper clamping force with the latches. If the latch is too loose, adjust the position of the latch hook to attain the proper  ension.  Always l o c k the latches before riding with TRAX lock set (sold separately).

ATTENTION
Make sure that the TRAX ION top case is properly attached to the SW- MOTECH adapter solution for TRAX and fully engaged to all four mounting points!
ALL latches of the TRAX ION top case must be locked BEFORE riding with the TRAX lock set [sold separately) and remain closed while riding. Improperly mounted cases run the risk of detaching during transport.
MOUNTING INSTRUCTIONS
Art.-Nr. / Item No: QLS.00.095.1510+
– Revision:00.- 04-2021
TRAX lock set with anti – th eft protection PRO
ATTENTION
NEVER lubricate lock cylinders with oil! Use graphite powder only!

| QLS.00.046.1510* (EVO)| 2/2
---|---|---
1| QLS.00.046.520| 2/2
2| CAM.2312S10-1BP| 2/2
3| ALK.00.165.A63| 2/2
4| ALK.00.165.562| 7/7

Errors and omissions excepted . Technical and design  modifications are subject to change.

Tel/phone: + 49 (0)6425 / 8168 – 050
Fax/fax: + 49 (0)6425 / 8168 – 10
infofasw-motech.com
www.sw-motech.com
Copyright by
SW-MOTECH GmbH & Co. KG

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>