SW-MOTECH GPT.06.921.19000/B Rackpack Set Yamaha Tracer 9 / Tracer 9 GT (20-) Instruction Manual
- October 27, 2023
- SW-MOTECH
Table of Contents
SW-MOTECH GPT.06.921.19000/B Rackpack Set Yamaha Tracer 9 / Tracer 9 GT
(20-) Instruction Manual
Thank you for choosing this premium product from SW-MOTECH. Please visit our webshop for additional information, such as application charts and PDF mounting instructions. Any other documents that may be required (e.g. ABE certifications), are also available for download at our webshop.
Installation and/or maintenance of this product require good technical understanding! For your own safety SW-MOTECH recommends having installation and/or servicing carried out by a specialist workshop! SW-MOTECH assumes no liability for damage caused by improper installation and/or maintenance work!
Carefully follow all the directions given in the mounting instructions and pay attention to all relevant information in the vehicle manual during assembly. Nonconformance can lead to vehicle damage or even endanger the driver! These mounting instructions are written based on our current state of knowledge. Legal requirements for accuracy do not exist.
This product was developed for vehicles in their factory setting. Compatibility with original accessory parts or other manufacturers” accessory parts is not guaranteed. Furthermore, BEFORE installing this product, make sure that all moving parts (e.g. the chain) are in the original state of maintenance. Installed accessories can change the driving behaviour and/or stability of your vehicle.
GENERAL INFORMATION
Observe the country-specific regulations concerning vehicle registration/ operation as well as TOV regulations if applicable. If required, register installed parts in the vehicle documents through an appropriate inspection authority.
PREPARATION: Read the mounting instructions carefully and make sure that all items of the parts list are included. Make sure that your vehicle is parked safely and cannot fall over. Turn off the engine and remove the ignition key. Let the motor/exhaust cool off if necessary. Disconnect the vehicle battery when working on the electrical system. Use appropriate tools. Have another person to help you.
MOUNTING: All parts and connections removed from the vehicle must be reinstalled in accordance with the vehicle manufacturers· specifications or replaced by parts delivered by SW-MOTECH. Secure all threads, unless otherwise specified, with medium-strength liquid thread locker.
Torque specifications undefined by SW-MOTE CH must be obtained from the vehicle manufacturer or by a specialist workshop!
FUNCTION CHECK: After installation make sure that all parts and connections previously removed are properly replaced. Also make sure that no moving parts are obstructed and no function of the vehicle is hindered in any way. Cables and hoses must not rub and/or be pinched. Before starting to ride. perform a comprehensive check of all functions. After the first 50 km and then at regular intervals, check the tightening torque of all screw connections and the proper fit of the product.
PRODUCT SPECIFIC INFORMATION
ATTENTION: The indicated maximum load is inclusive the weight of topcase/luggage and adapter kit! The maximum vehicle load specified by the manufacturer must not be exceeded!
ATTENTION: Can only be mounted in combination with the original luggae grid!
PARTS LIST
Note: a All measurements in millimeters. b The second number indicates the total quantity of the part in the delivery.
No torque specifications: Use the torque defined by vehicle manufacturer! The standard torque in this table can be used as long as it is within the vehicle manufacturer’s specifications.
MOUNTING
Attach the mounting bracket [1) to the luggage rack, as shown in the drawing.
ATTENTION: Use liquid thread locker!
Tighten the screws as specified.
NOTE: Depending on the available space, attach the luggage rack to the marked mounting position (A} or (BJ, as shown in the detail drawing.
Attach the luggage rack [8) to the mounting bracket [1 ), as shown in the
drawing.
ATTENTION: Use liquid thread locker!
Tighten the screws as specified.
MOUNTING INSTRUCTIONS
Extension for ADVENTURE-RACK
Thank you for choosing this premium product from SW-MOTECH. Please visit our webshop for additional information, such as application charts and PDF mounting instructions. Any other documents that may be required (e.g. ABE certifications), are also available for download at our webshop.
Installation and/or maintenance of this product require good technical understanding! For your own safety SW-MOTECH recommends having installation and/or servicing carried out by a specialist workshop! SW-MOTECH assumes no liability for damage caused by improper installation and/or maintenance work!
Carefully follow all the directions given in the mounting instructions and pay attention to all relevant information in the vehicle manual during assembly. Nonconformance can lead to vehicle damage or even endanger the driver! These mounting instructions are written based on our current state of knowledge. Legal requirements for accuracy do not exist.
This product was developed for vehicles in their factory setting. Compatibility with original accessory parts or other manufacturers” accessory parts is not guaranteed. Furthermore, BEFORE installing this product, make sure that all moving parts (e.g. the chain) are in the original state of maintenance. Installed accessories can change the driving behaviour and/or stability of your vehicle.
GENERAL INFORMATION
Observe the country-specific regulations concerning vehicle registration/
operation as well as TOV regulations if applicable. If required, register
installed parts in the vehicle documents through an appropriate inspection
authority.
PREPARATION: Read the mounting instructions carefully and make sure that all items of the parts list are included. Make sure that your vehicle is parked safely and cannot fall over. Turn off the engine and remove the ignition key. Let the motor/exhaust cool off if necessary. Disconnect the vehicle battery when working on the electrical system. Use appropriate tools. Have another person to help you.
MOUNTING: All parts and connections removed from the vehicle must be reinstalled in accordance with the vehicle manufacturers· specifications or replaced by parts delivered by SW-MOTECH. Secure all threads, unless otherwise specified, with medium-strength liquid thread locker.
Torque specifications undefined by SW-MOTE CH must be obtained from the vehicle manufacturer or by a specialist workshop!
FUNCTION CHECK: After installation make sure that all parts and connections previously removed are properly replaced. Also make sure that no moving parts are obstructed and no function of the vehicle is hindered in any way. Cables and hoses must not rub and/or be pinched. Before starting to ride, perform a comprehensive check of all functions. After the first 50 km and then at regular intervals, check the tightening torque of all screw connections and the proper fit of the product.
PARTS LIST
All measurements in millimeters. · 0 The second number indicates the total quantity of the part in the delivery.
••• No torqu& specifications: Use the torque defined by vehicle manufacturel’! The standard torque in this table can be used as long as it is within the vehicle manufacturer’s specifications.
MOUNTING
ADVENTURE RACK
Attach the shown parts to your ADVENTURE RACK (sold separately).
ATTENTION: Use liquid thread locker!
Tighten the screws as specified in the parts list.
Adapter plate for STREET-RACK
Attach the shown parts to your adapter plate for STREET-RACK (sold
separately).
Tighten the screws as specified in the parts list.
Adapter plate for ALU-RACK
Attach the shown parts to your adapter plate for ALU-RACK (sold separately).
Tighten the screws as specified in the parts list.
MOUNTING INSTRUCTIONS
Item No.: BC.HTA.00.305.3000*
PRO Rackpack tail bag
Thank you for choosing this premium product from SW-MOTECH. Please visit our webshop for additional information, such as application charts and PDF mounting instructions. Any other documents that may be required (e.g. ABE certifications), are also available for download at our webshop.
Installation and/or maintenance of this product require good technical understanding! For your own safety SW-MOTECH recommends having installation and/or servicing carried out by a specialist workshop! SW-MOTECH assumes no liability for damage caused by improper installation and/or maintenance work!
Carefully follow all the directions given in the mounting instructions and pay attention to all relevant information in the vehicle manual during assembly. Nonconformance can lead to vehicle damage or even endanger the driver! These mounting instructions are written based on our current state of knowledge. Legal requirements for accuracy do not exist.
This product was developed for vehicles in their factory setting. Compatibility with original accessory parts or other manufacturers· accessory parts is not guaranteed. Furthermore, BEFORE installing this product, make sure that all moving parts (e.g. the chain) are in the original state of maintenance. Installed accessories can change the driving behaviour and/or stability of your vehicle.
GENERAL INFORMATION
Observe the country-specific regulations concerning vehicle registration/
operation as well as TOV regulations if applicable. If required, register
installed parts in the vehicle documents through an appropriate inspection
authority.
PREPARATION: Read the mounting instructions carefully and make sure that all items of the parts list are included. Make sure that your vehicle is parked safely and cannot fall over. Turn off the engine and remove the ignition key. Let the motor/exhaust cool off if necessary. Disconnect the vehicle battery when working on the electrical system. Use appropriate tools. Have another person to help you.
FUNCTION CHECK: This is a universal product. For this reason make sure BEFORE the first use, that the product can be fixed properly and used without problems with your vehicle type. After fixation also make sure that no moving parts are obstructed and the function of the vehicle is not hindered in any way. Lamps as taillight and turn signals must not be limited in their function. Cables and hoses must not rub and/or be pinched. Before starting to ride, perform a comprehensive check of all functions.
All components of the product must not contact any hot or moving parts of the vehicle. All parts should also remain 5 cm away from hot parts of the vehicle and remain clear of the exhaust stream. For this reason compress the suspension fully several times with your vehicle stationary. ATTENTION: Before riding and at each stop (every 200 km) check proper fixation of the product!
PRODUCT SPECIFIC INFORMATION
ATTENTION: Riding with this product may affect the motorcycles driving and
braking performance! Cornering and ground clearance can be reduced by using
this product!
ATTENTION: Modifications will void any warranty.
ATTENTION: The maximum vehicle load specified by the manufacturer must not be exceeded!
ATTENTION
NOT FOR OFFROAD-USE!
PARTS LIST
Note: a All measurements in millimeters. b The second number indicates the total quantity of the part in the delivery.
No torque specifications: Use the torque defined by vehicle manufacturer! The standard torque in this table can be used as long as it is within the vehicle manufacturer’s specifications.
FASTENING
FIXED ON THE LUGGAGE RACK EXTENSION
Step [1]: Loop two loop straps (4) together.
Step [2]: Guide the loop straps (4] through the shown openings of the example
luggage rack extension.
Step [3]: Hook the cam-hooks of the loop straps (4) onto the 0-rings of the
tail bag [1).
Step [4]: Pull the loop straps [4) on all four cam-hooks tight.
Step [5]: Roll up the excess lengths of the loop straps [4) …
Step [6]: … and fix it with the velcro straps.
FASTENING TO THE LUGGAGE RACK
Step [1]: Loop the velcro straps [6) and [7] onto the loop at the bottom of
the tail bag [1). Make sure that the loop and hook sides can be easily
attached.
Place the tail bag [1 I on the luggage rack.
Step [2]: Fasten the tail bag [1 J to your luggage rack with the velcro straps
[6) and [7). Make sure that the tail bag (1 I is fastened in such a way that
it cannot slip while driving.
OPTIONAL: The velcro strap sewn on the front can be looped around the backrest to provide additional support.
UNIVERSAL FASTENING:
Step [1] & [2]: Cover the contact surfaces of the tail bag [1 l with the
protection foil [5). Clean the surface before applying the protection foil.
Step [3]: Place the tail bag [1) on the rear of the vehicle.
Step [41: Entangle the loop straps [4) to FOUR suitable and Loadable fastening points to the vehicle, as shown in the example illustrations [Al to [Cl (e.g. vehicles frame, footrest mounts, Luggage hook etc.).
ATTENTION: The fastening points must be chosen so that the tail bag (1) is secured against slipping! To do this, tension the tail bag (1) to the front at the two front fastening points and to the rear at the two rear fastening points!
Step [5]: Hook the cam-hooks of the FOUR Loop straps 14) onto the D-rings of
the tail bag (1).
Step [6]: Pull the Loop straps (4) on all four cam-hooks tight until the tail
bag 1 is centered and securely fastened to the vehicle.
Step [7]: Roll up the excess Lengths of the Loop straps 14) …
Step [8]: … and fix it with the velcro straps.
ATTENTION: All components of the tail bag must not contact any hot or moving parts of the vehicle. All parts should also remain 5 cm away from hot parts of the vehicle and remain clear of the exhaust stream.
ALL
FASTENING POSSIBILITIES
ATTENTION: Before riding and at each stop (every 200 km) check the proper
fixation of the tail bag (1 )!
LOADING AND CARE
ATTENTION: Always use the included waterproof innerbag (2) to protect your luggage from moisture!
Fasten the waterproof inner bag (2) to the velcro patch on the inside. Additionally protect sensitive luggage (e.g., electronic equipment) from moisture with a plastic bag.
LOADING: Never store pointy or sharp-edged objects, which could cause injury to persons or damage to the vehicle/product!
ONLY loop assigned SW-MOTECH products to the MOLLE attachment1
CARE: For cleaning use ONLY a soft textile brush, cloth or sponge and
warm soapy water! Rinse with clean water.
Do NOT use strong cleaning agents, rough cleaning tools or high pressure
washer!
Clean the product after riding in salty conditions, to avoid damage from salt.
Read More About This Manual & Download PDF:
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>