ATUMTEK ATSS002 Bluetooth Selfie Stick Pro User Manual
- June 6, 2024
- ATUMTEK
Table of Contents
User Manual
BLUETOOTH SELFIE STICK PRO
Product Introduction
Product Parameters
Weight | Approx. 172g |
---|---|
Remote distance | <10m(33ft) |
Ambient temperature | -10°C∼50 °C |
Remote battery capacity | 50 mAh |
Input | 5V/110 mAh |
Compatible devices | IOS 7.0 and later/Android 5.0 and later |
Device width | Approx. 2.16-342 in |
Extended length w/o
tripod activated
| Approx. 7.7-31.3 in
Extended length with
tripod activated
| Approx. 8.7-32.9 in
Folded size| Approx. 7.7*1.18 in
Remote button lifespan| >15,000 times
How to take out / put in wireless Bluetooth remote
- Take out from the of the Remote.
- Put in from the top Remote bottom.
How to use
Step 1 : First unlock the 3 legs at the bottom slightly; then pull the
top cap out about 2cm; (Be careful and do not get hurt by the clamp!!!) Now
pull the whole stick arm out, and the tripod will open automatically.
ATTENTION:
- Please fully pull out the stick arm so that the tripod can be fully opened. Otherwise, a tripod is not fully opened and will not be stable.
- Please don’t pull the legs to open the tripod!!!
Step2: Put the tripod on a flat surface, then adjust the extendable stick ami for suitable height. If you do not need to use it as a tripod, just pull out the stick arm and adjust the height to use it.
Step3: Widthwise set your phone inside the smartphone holder by releasing
the top cap.
Note: please avoid sticking the button on your phone.
Remove your mobile phone by releasing the top cap. Then, hold the product’s middle position and use the other hand to push the aluminum alloy telescopic arm back from the top cap. Note: If you open the tripod, the tripod will close automatically when pushing back the aluminum alloy telescopic arm. Manual operation is prohibited.
WARNING: Do not push the 3 legs to close!!! It will break legs!!!
Bluetooth Connect Instruction
No. | Status | LED Light Indicator |
---|---|---|
1 | Switch On | Green Light Flashing |
Long press the camera button for 2 seconds, to open the remote.
2| Switch Off| LED Light OFF
Long press camera button for 3 seconds, remote light is OFF.
3| Standby| LED Light OFF
Remote will standby after 10 minutes without operation; Press the button for
once to active, then the green light will flash, please reconnect with the
phone again.
4| Low Power| Red Light Flashing
5| Charging| Red Light ON
6| Fully Charged| LED Light OFF
7| Connected| Green Light ON
8| Connectionless| Green Light Flashing
First long press the camera button for 2 seconds, then connect with “ATUMTEK” when the green light is flashing, finally press once to take a picture or record a video.
If the phone could not connect, clean the phone’s Bluetooth connection first, then try again; some Android phones use the volume button to control the camera, so if you still could not use remote, please choose “take a picture” or “take a video” on camera setting part.
Or please contact the seller directly to get support.
NOTE:
- Open your built-in camera in your phone and press the power & camera 2 in 1 button once for taking a photo.
- The wireless Bluetooth remote will connect directly after switching on if it is already connected with the phone Bluetooth last time.
- The Bluetooth will automatically disconnect when the distance is greater than or equal to 10 meters.
- Turn the Bluetooth off in your phone and the wireless Bluetooth remote will
- How to disconnect with your phone: Go to your phone’s Bluetooth setting and disconnect “ATUMTEK” in paired devices.
- Unavailable to use to control the built-in camera app in your phone when the wireless Bluetooth remote is charging.
Contact us via Facebook Messenger (Recommended):
m.me/atumtekproducts
OR
www.atumtek.com
OR
support@atumtek.com
If you find our product satisfactory, please encourage us by sharing your user
experience online.
If you need help with this purchase, please do not hesitate to contact us.
EC | REP |
---|
Syncwire UK Ltd C/O Lai and Co.109 Portland Street, Manchester, M1 6N