ATUMTEK ATSS001 Tripod Selfie Stick User Manual

June 6, 2024
ATUMTEK

ATUMTEK logo

ATUMTEK ATSS001 Tripod Selfie Stick

ATUMTEK ATSS001 Tripod Selfie Stick image

Product Introduction

ATUMTEK ATSS001 Tripod Selfie Stick fig1

Product Parameters

Product model ATSSOOl
Weight Approx. 157g
Remote distance <10m(33ft)
Ambient temperature -l0″C~S0°C
Remote battery capacity Replaceable 3 Volt Lithium Cell CRl220 38mAH
Compatible devices 105 7.0 and above I Android 5.0 and above
Device width Approx. 2.16-3.42 in
Extended length w/o tripod activated Approx. 7.2-29.3 in
Extended length with tripod activated Approx. 9.6-27.1 in
Folded size Approx. 7.2*1.18 in
Remotebutton lifespan >8,CXXJ times

How to take out or put back the wireless Bluetooth remote?

ATUMTEK ATSS001 Tripod Selfie Stick fig2

Take it out Pull up the top part of ATIJMTEKSelfie stick about 5 cm, then push the Bluetooth remote from bottom to top and take it out from the remote slot. Please refer to picture 1 and 2
Put it back on: Pull out the top part of ATUMTEK selfie stick about 5 cm, then push the Bluetooth remote from top to bottom and place the remote back in the Remote slot as shown. Please refer to picture 1 and2

How to active the Bl uetooth remote battery?

  1. Taking out the wireless Bluetooth remote, hold it and push the battery cover from bottom to up about 1 mm to loose the battery cover;
  2. Use your finger to lift the top part of the battery cover, and remove the cover.
  3. Take out the Lithium cell from battery slot, then remove the plastic insulating strip and put the Lithium cell back.
  4. Push the battery cover from top to bottom, lock the cover.

How to replace the Lithium Cell battery?

First please refer to the above step 1 &2, then take out the Lithium battery, and put new battery in the slot; Finally lock the battery cover

How to use the selfie stick?

Step 1: Hold the bottom part of ATUMTEK selfie stick, rotate phone bracket upward till 90° to selfie stick. (From back side of the Product.)ATUMTEK ATSS001 Tripod Selfie Stick fig7 Step 2: Horizontally rotate the phone bracket 180″ to the front side of the product, now the phone bracket can be rotated 90° vertically. Step 3: Hold the bottom part of ATUMTEK selfie stick and use another hand to pull up the stick to your suitable length freely.ATUMTEK ATSS001 Tripod Selfie Stick
fig9
Note: Open all three of the tripod legs at the bottom manually to activate the tripod if you want to use the tripod. Put the tripod stand on fiat surface when you use it.
Step4: Pull up the foot cushion on the smartphone holder and widthwise set your phone inside the adjustable sliding bracket on the smartphone holder.ATUMTEK ATSS001 Tripod Selfie Stick fig10
Note: please avoid sticking the buttons of your phone.

How to close?

Step 1: Remove your mobile phone by releasing the adjustable sliding bracket. Then, hold the product middle position and use the otherhand to push the aluminum alloy telescopic arm back from the top.ATUMTEK ATSS001 Tripod
Selfie Stick fig11 Note: If you open the tripod, putting back the tripod manually,the magnetic type tripod will close together.
Step 2: Rotate the phone holder 90° vertically, then 180° horizontally, ensure the phone bracket is on the back side of the product. Push down the phone holder near to the stick.ATUMTEK ATSS001 Tripod Selfie Stick
fig12

CAUTIONS:

  1. Please use it in an ambient temperature between 10°C to50°C.
  2. Please do not continuously rotate the smartphone holder in high frequency.
  3. Please do not continuously and frequently pull the aluminum alloy telescopic arm up and down.
  4. Push out on all three of the tripod legs attached to the stem at the button to activate the tripod.

LED light instruction

No. Status LED Indicaot r Ligh t


1

| Switch On| Green Color On
Keep pressing the power & camera 2 in 1  button for  2 seconds, the green light of the wireless Bluetooth remote will be on or flash about 05 seconds. Search’ ATUMTEK’ Bluetooth device on your phone and connect with it.


2

| Switch Off| OFF
Long press for 3 seconds, the light of wireless Bluetooth

remote is OFF.






3

| Standby| OFF
The wireless Bluetooth remote will standby when in

connections status after 2 minutes.

Note: The remote would not switch off in standby status; Press the power & camera 2 in 1 button for once and then the green light will flashes. This means the remote is

available le to connect to phone Bluetooth.


4

| Low Power| Green Color Flashing Continuously
The green light of the wireless blueooth remote will flash continuously when the power is low, about twice every 3

seconds.



5

| Connected| Green Color On
The light of the wireless Bluetooth remote will display green when connected with the device’s Bluetooth. This means it is available to control the built- in camera app on your phone to

take a photo



6

| Connectionless| Green Color Flashing
The green light of wireless Bluetooth remote will flash when connected less with the device’s Bluetooth.In this case, please turn the Bluetooth in your phone on and choose to

connect. ATl.JM TEK”


NOTE :

  1. Open your built-in camera in your phone and press the power & camera 2 in 1 button of once for taking a photo.
  2. The wireless Bluetooth remote will connect directly after switch on if it is already connected with the phone Bluetooth in last
  3. The Bluetooth will automatically disconnect when the distance is longer than or equal to 10 met
  4. Turn the Bluetooth off in your phone and the wireless Bluetooth remote will
  5. How to disconnect with your phone: Go to your phone Bluetooth setting and disconnect ATUMTEK” ln paired devices.

Contact us via Facebook Messenger (Recommended):

m.me/atumtekproducts
OR
www.atumtek.com
OR
support@atumtek.com

If you find our product satisfactory, please encourage us by sharing your user experience online.

If you need help with this purchase, please do not hesitate to contact us.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals