ATUMTEK ATRL140 10 Inch Selfie Ring Light User Manual

June 14, 2024
ATUMTEK

**ATUMTEK ATRL140 10 Inch Selfie Ring Light

**

CAUTION

  1. Please follow the instructions carefully for safe using and keep user manual for future reference.
  2.  Please keep the light away from water or any other liquid to avoid electrical shock.
  3. Please keep away from heat and avoid direct sunlight.
  4.  Do not use It as a toy. Keep the equipment out of reach of children or Infants, avoid strangulation caused by the adapter cable.
  5.  Do not operate the device with wet hands.

IC Warning

This device complies with Industry Canada license-exempt RSS standard(s).
Operation is subject to the following two conditions:
(1) this device may not cause interference, and
(2) this device must accept any interference, including interference that may cause undesired
operation of the device.
IC RF Statement: When using the product, maintain a distance of 20cm from the body to ensure compliance with RF exposure requirements.

FCC Statement

Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and [2) this device must accept any interference received, Including interference that may cause undesired operation, Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Patt 15 of the FCC Rules, These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy, and if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation.
If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

  • Reorient or relocate the receiving antenna.
  • Increase the separation between the equipment and receiver.
  • Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
  • Consult the dealer or an experienced radio/TV technician for help.

Product Introduction

Material: ABS+ PC+ Steel Desk Stand Height: from 11 AH to 15.7″ Phone Clamp Size: Fit phone width 2.3″ to 3.6″ Remote Battery: CR2032 3V lithium battery 70 mAh Wireless Remote Distance: 33 ft/10 m Wireless Remote Version: Wireless 5.2fit iOS 7.0 & Android 5,0 above devices Wireless Name: ATUMTEK Wireless Name: ATUMTEK Ring Light Input Voltage: 5V/2AColorTemperature: 3000K-6000KCRI

90

Package Includes

  • 1 O” LED Ring Light with USB Power Supply

1 * Extendable Phone Holder

1 *Tripod Ball Head

1 * Wireless Remote Shutter

1 * User Manual

1 * Adjustable Desktop Stand

Step 1 Mount Adjustable Pole on Stand Base

First, remove the fasten screw from the bottom of adjustable pole_ Then, attach and mount the adjustable pole to the stand base ( Attention: stand base backside with anti-slip mat).

Step2 Mount Swivel Ball Head on Stand

Mount swivel ball head on stand pole. Loosen pole adjustment joint to adjust height, and finally fasten at suitable height.

Step3 Assembly the Ring Light

Install the ring light on stand ball joint head, then Fasten the knob.

Adjustment: Loosen the adjustable knob, to adjust right light at suitable angle, then fasten the knob.

Step4 Mount Phone on Phone Holder & Adjust Phone Holder (360°

rotation).

Ring Light Adjustment

Put ring light on fiat surface and connect USB power port (Input SV /2A) with charging adapter, power band or other USB charging port. Blue LED indicator will be light up.

Power ON/ OFF

Press 00 to turn on / off the stand light.

Lighting Mode Setting When the stand light is on, repeatedly press to cycle through Cool White-> Warm White -> Warm Yellow lighting modes.

Cool White

Warm White

Warm Yellow

Brightness Adjustment

  1. When the stand light is on, repeatedly press or to adjust
    the brightness by step (10%-100%).

  2.  Or press and hold or to sleeplessly adjust the brightness.

Wireless Remote Shutter Instruction

  1. LED
  2. Remote Shutter Button (Android/IDS)
  3. Battery (included)
  4. ON/OFF

Pairing:

  1. Turn on remote first by switch ON/OFF button, LED light is fishing quickly then slowly to search devices.
  2. Open the function on phone to search and connect with “ATUMTEKH remote shutter. Remote Light is off after connected.
  3. Remote will be shut down after 5 minutes no pairing action.

Take a Picture:

Press shutter button once to take picture, LED light fishes when you press_

Take a Video

Long press shutter button to take a video, LED lightfaces while you are pressing it. Video will end when you stop pressing button,

Camera Apps Issue:

Use inbuilt camera App or download “camera 360” App (find in Google Play), then use remote shutter to take picture or video through Apps.

Standby

Remote will standby after 90 seconds without operation; Press the button for once to activate again

After First Time Connection:

Once connected with phone successfully for the first time, remote will connect with phone automatically next time, Remember to turn close remote after using,

  • For Some Android phones could not contra Apps, can just control phone camera. Sony Xperia S HTC New one and X+ Other Android Phones.

Solutions When Remote control Failed to Connect with Phone

  1.  Clear some paired device when your phone have connected with too many devices.
  2.  Remove battery then put battery back again, try to turn remote on again.
  3.  Turn on phone Bluetooth, and turn on remote control, when “ATUMTEK is found on the mobile phone, click “connect”; When Connecting/pairing” is displayed on the interface, press remote button continuously and quickly to connect.

About Android System Phones Connection:

Some Android phones use phone volume button to control camera or zoom. Please reset on phone camera settings, find volume key function, set the volume key function to shutter. (Do not select zoom or focus,)

Tips about the battery:

  1.  The life of the battery depends on the frequency of use of the remote control.
  2.  When not using the remote control, remember to turn off the remote control to save power.
  3.  When the battery is dead, remember to change the battery in time, you can go to the local store to buy the battery,

To access this ATUMTEK product instructions in different languages, please scan the QR code provided.
Once scanned, you’ll be directed to a PDF document, which you can open in your browser and download for your reference.

Thank you for choosing ATUMTEK!

ATUMTEK provides warranty coverage of 36 month on all of Its brand
name products purchased through authorized channels.
support@atumtek.com

EC/REP Prolinx GmbH

Brermstr.56. 40239 Dusseldorf Germany

Sync wire Uk Ltd

UK /REPC/O Lai and CO.109 Portland Street( Manchester, M1 6N

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals