TCL 1J8VNKSOG 52 Inch Ceiling Fan User Manual

TCL 1J8VNKSOG 52 Inch Ceiling Fan User Manual

Safety Information

1. To avoid electric shock or fire hazard, do not apply a voltage or power outside the range specified of the product.

2. To reduce the risk of electrical shock, the electricity supplied to the ceiling FAN must be cut off before installation.

3. All wiring must be in accordance with the National Electrical Code NASI/NFPA 70 -1999 and local electrical codes. Electrical installation should be performed by a qualified licensed electrician.

4. To reduce the risk of electric shock, this fan must be installed with an isolating wall control/switch.

5. No matter the ceiling is made of wood or concrete, the ceiling must support at least 35lbs (15.9kg).
   Otherwise, the fan would drop down.

6. Do not insert foreign objects in between rotating fan blades.

7. A minimum height of 7.5 ft. (2.3m) between the fan blades and floor must be kept, otherwise it may cause injury.

8. Do not operate the reversing switch while the fan blades are in motion.You must turn the fan off and stop the blades before you reverse the blade direction.

9. Chemical burn hazard. Keep batteries away from children. This remote contains a lithium button cell battery. If a new or used lithium button/coin cell battery is swallowed or enters the body, it can cause severe internal burns and can lead to death in as little as 2 hours. Always completely close the battery compartment. If the battery compartment does not close securely, stop using the product, remove the batteries, and keep it away from children. If you think batteries might have been swallowed or placed inside any part of the body, seek immediate medical attention. Dispose of cells properly and keep them away from children. Even used cells may cause injury.

Care and Cleaning

WARNING: Make sure the power is off before cleaning your fan.

• Because of the fan’s natural movement, some connections may become loose. Check the support connections, brackets, and blade attachments twice a year. Make sure they are secure. It is not necessary to remove the fan from the ceiling.
• Clean your fan periodically to help maintain its new appearance over the years. Do not use water when cleaning, as this could damage the motor or the wood, or possibly cause an electrical shock. Use only a soft brush or lint-free cloth to avoid scratching the finish. The plating is sealed with a lacquer to minimize discoloration or tarnishing.
• You can apply a light coat of furniture polish to the wood for additional protection and enhanced beauty. Cover small scratches with a light application of shoe polish.
• You do not need to oil your fan. The motor has permanently-lubricated sealed ball bearings.

Help

This User Manual is designed to make installation as simple as possible. While working through this User Manual, keep your smartphone or tablet nearby. We have added video links to help you through the more technical sections on website. If you are unfamiliar or uncomfortable with wiring or repairing, contact a qualified electrician. We also provide telephone support at 4044515129 or email us.

Use of Remote Control

Note: The remote works with battery 1.5V AAA x 2pcs (not included)

1. LED indication light
2. ON/OFF the light
3. ON/OFF the Fan
4. Speed of the fan
5. Reverse switch
6. Natural wind
7. Anti-theft light
8. Delay closing fan
9. Timing control

Note:

Reverse Switch:

Ceiling fans work in two directions: downdraft (counterclockwise rotation) and updraft (clockwise rotation). To change the direction of air flow, turn the fan off and let it come to a complete stop. Press the reversing switch to the opposite position. Restart the fan.

Updraft(clockwise rotation) creates a more indirect airflow. Updraft airflow is great for moving warm air downward.

Downdraft(counterclockwise rotation) creates a direct breeze and maximum cooling effect.

Natural Wind:

The ceiling fan adopts DC frequency conversion motor that can creates Natural Wind (sometimes strong, sometimes week) with quite, energy-saving and long life time.

Anti-theft light:

If Anti-theft Light function is activated, the LED lights will automatically light up for 1 minute every 30 minutes, until the function is canceled by pressing the button again. It could give a signal to any theft due to the light, the room is not empty when you are leaving.

Delay closing fan:

Once Delay Closing of Fan is selected, the FAN will be powered off within 1 minute.

Product Specification

Ceiling Fan Size: 52″
Material: Silicon Steel/Copper/Plastic Blade
Light Cover Material: Acrylic
Control Mode: Remote Control
LED Light Number: 30pcs LEDs
Light Color Temperatures: 3000k/4500k/6000k
Motor: DC Frequency Conversion
Voltage: 120V~60Hz

Function:

1. Fan Speed(low 1-high 6)
2. Fan Direction: Downdraft/Updraft
3. Natural Wind
4. Anti-theft Light
5. Delay Closing Fan
6. Fan Timing(1H,4H,8H)

TOOLS REQUIRED

Operation

OPERATING YOUR FAN

Power on the electricity, turn on the LED lights and start Fan running by remote controller.

Note: Please watch the video of installation from the product listing on website if you meet a problem when installing.

Assembly – Attaching the Lights

3. Install the Acrylic shade

1. Attach the acrylic shade to the lightkit and twist clockwise until it is secured tightly.

Checking Material

HARDWARE INCLUDED

NOTE: Hardware not shown to actual size.

PACKAGE CONTENTS

Installation of the Hanging Bracket

1. Switch off the electrical mains breaker.
2. Screw up four self-tapping screws with electric automation driller on the wood ceiling to fix the Mounting Bracket as shown in the picture above.

Important Notice:

No matter the ceiling is made of wood or concrete, the ceiling must support at least 35 lbs (16kg). Otherwise, the fan would drop down.

Assembly – Attaching the Lights

1. Tighten the screw of the box cover.
   

2. Remove three screws from the motor round piece.

3. Attach the lightkit to the fan, fix three screws back to the hole and tighten all the three screws.

4. Connecting lamp wire
   
   CAUTION: To reduce the risk of electric shock, disconnect the electrical circuit to the fan before installing the light fixture.

5. Directly plug in the wire to the lightkit docking.

Assembly – Install the Canopy

1. After wiring is done, put the remote control receiver in the mounting bracket.
2. Carefully push the canopy to the bottom of the mounting bracket, and then screw up the two screws clockwise.

Assembly – Attaching the Fan Blades

1. Remove the Upper housing
   
   

2. Remove six screws from the top of motor.

3. Remove the Round piece and upper housing.

4. Attaching the blades to the blade tray
   
   Install two screws for each blade. One by one, until three of blades have been installed
   (The screws can be found in the hardware bag.)

5. Install back the Uper housing
   
   

6. Install back the upper housing and round piece;

7. Tighten the six screws

Install the Hanging Part of the Ceiling Fan

1. Install downrod assembly
   

2. Remove the ‘R’ pin and Cross pin from the down rod.

3. Install the canopy and Coupling cover through the down rod.

4. Thread the wires through the downrod, insert the downrod into the Coupler and Loosen the two screws on the Coupler.
   

5. Install back the Cross pin and secure with the ‘R’ pin, the ‘R’ pin must be properly installed to prevent the Cross pin from working loose.

6. Tighten the two screws on the Coupler.

Hanging the Fan

1. Carefully lift the fan and assembly into Mountain bracket which is attached to the outlet box. Ensure the rod ball’s groove is lined up with tab on the hanger bracket.

Assembly – Wiring of Ceiling Fan

1. Making the electrical connections
   WARNING: The ceiling fan must be grounded.If the ground wire for the installation site is not present, immediately STOP installation and consult a qualified electrician.
     IMPORTANT: Use the plastic wire connectors supplied with your fan. Secure the connectors with electrical tape and ensure there are no loose strands or connections.

1. As per the picture above, install three motor wires into the motor connector of remote receiver and then use screwdriver to tighten the connection. Wire sequence can’t be mixed, the sequence is that Pink- U (left), Grey-V (middle), Red-W(right).
2. Install LED Light wires to the Light connector as shown in the picture above blue wire to L terminal, white wire to N terminal.
3. Connect L and N wires from Power to the connector of Power Input on remote controller with plastic wire nut; and connect grounding wire from Power to the grounding wire from Motor Wire connection: White to N, Black to L, Green to Green.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>