Barrette Standard Chain Link / Farm Hinge Instructions

June 6, 2024
Barrette

Barrette Standard Chain Link / Farm Hinge

WARNING:

  • Improper installation of this product can result in personal injury. Always wear safety goggles when cutting, drilling and assembling the product.
  • Incorrect installation may cause harm to the gate or individual.

NOTICE:

  • DO NOT attempt to assemble the kit if parts are missing or damaged. ·
  • DO NOT return the product to the store, for assistance or replacement parts call: 1-877-265-2220.

BEFORE YOU BEGIN

Vinyl gate posts require an internal support system for weight-bearing purposes and therefore wooden inserts or a post stiffener is required. Post stiffener needs to be purchased separately.

Top View of Routed Post

TOOLS NEEDED

| Safety Glasses
---|---
| Tape Measure
| Gate
| 9 ⁄16″ or 14 mm Wrench

*Additional U-clamps, nuts and washers may need to be purchased if gate upright diameter is larger than 13 ⁄8″.

Component list
QTY Description

2

| Standard Chain Link/Farm Hinge

4

| 13 ⁄8″ U-Clamps

4

| 21 ⁄2″ U-Clamps

16

| 5 ⁄16″ Hex Nuts

26

| 5 ⁄16″ Washers

1

| M6/M5 “Z” Allen wrench


To obtain and review a copy of the warranty please visit:barretteoutdoorliving.com. You may also contact us at 1-877-265-2220 or emailCs.outdoorliving@ebarrette.com

Installation

Determine Gate Opening

Gate opening is determined by width of gate plus clearance for hinge (2″) plus clearance for latch (see latch instructions for details) (Fig. 1).

Mount Hinge on Gate

NOTE:
Gate can be adjusted to swing up to 160º. When mounting gate on left gate post, head of tension adjustment pin and “+ or -” symbol on hinge should be facing up. Hinges have a self-closing feature, which can be disabled if desired (see hinge tension adjustment).
a. Place hinges at desired positions on gate upright with a minimum spacing of 32″ between each hinge.
b. Remove nuts from 13/8″ U-clamps and slide ends of U-clamps through mounting holes in gate plate, as shown (Fig. 2).

NOTE:
If gate upright is larger than 13/8″ in diameter, you must purchase the appropriately sized U-clamp, nuts and washers.*
c. Thread nuts onto U-clamp ends and tighten with 9/16″ or 14 mm wrench (Fig. 3)

Mount Gate on Post

NOTE:
Both gate posts must be plumb and level prior to gate installation.
a. Position gate at desired height on post.
b. Measure space between ground and bottom of gate and cut (2) wood spacer blocks for this height (Fig. 4).

c. Rest gate on the spacer blocks
d. Remove nuts from the 21/2″ U-clamps and slide ends of U-clamps through mounting holes in post plate, as shown (Fig. 5)

NOTE: If post is less than 21/2″ in diameter, you must purchase the appropriately sized U-clamp, nuts and washers.*
e. Thread nuts onto U-clamp ends and tighten with a 9/16″ or 14 mm wrench

Horizontal adjustment

Gate can be adjusted horizontally, if required.
a. Loosen (but DO NOT remove) the (2) adjustment screws with the included allen wrench (Fig. 6).
b. Move the gate to the left or right, as desired.
c. Re-tighten the (2) adjustment screws

Tension adjustment: (Fig. 7)
NOTE: HINGE TENSION IS PRE-SET AT THE FACTORY and usually DOES NOT REQUIRE ADJUSTMENT. If you wish to change tension setting/gate swing speed, or completely disable the self-closing feature, please see the following:

Fig. 6 Allen Wrench

Hinge Tension Adjustment

a. Place included Allen wrench into head of tension adjustment pin in hinge. The head is at the end closest to the + or – symbol on the hinge barrel (Fig. 7).


NOTE:
DO NOT
remove the Allen wrench or release the tension on the tension adjustment pin at any time during the adjustment.
b. Following the indicators on the + or – symbol on the hinge barrel, press down on the tension adjustment pin and turn toward the + to tighten, or toward the – to loosen (Fig. 7). Self-closing feature can be disabled by using the Allen wrench to push down and turn towards the “-” symbol until the gate no longer shuts on its own.Do not over-tighten or over-loosen the tension adjustment pin, as this may damage the tension spring.
c. When you have set the desired tension, simply release the downward pressure on the tension adjustment pin to lock it back into the hinge barrel. Tabs on pin head will fit into notches in hinge barrel when pin is in fully locked position (Fig. 8).

Barrette Outdoor Living
545 Tilton Rd, Egg Harbor City, NJ. 08215
barretteoutdoorliving.com877-265-2220

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Barrette User Manuals

Related Manuals