north states 4940 3-In-1 Wood Super Yard Instruction Manual

north states 4940 3-In-1 Wood Super Yard

IMPORTANT: PLEASE KEEP FOR FUTURE REFERENCE!
For helpful tips and instructions, please visit our website: www.northstatesind.com or contact our Customer Care department via email: CustomerService@northstatesind.com
Phone:763-486-1754 or Toll Free: 800-848-8421

IMPORTANT: Retain for future reference – Read carefully
Read the en instru on before assembling and installing this product. If you sell or give away this product, make sure you give this instru on to the new owner. Thank you.

WARNING

• Children have died or been seriously injured when gates are not properly secured.
• ALWAYS install and use gates as directed using all required parts.
• STOP using when a child can climb over yard or dislodge the gate.
• Install only with locking/latching mechanism securely engaged.
• To prevent falls, NEVER use at top of stairs.
• NEVER use to keep child away from pool.
• This product will not necessarily prevent all accidents.
• NEVER leave child unattended.
• This product is intended for use with children from 6 months up to 24 months of age.
• Periodically check all fasteners to be sure they are tight and secure, STOP using 3-in-1Superyard if any parts are missing or become damaged.
• When set up as a barrier, use in openings 53.75” to 151” (136.5 cm to 383.54 cm).
• Hardware is included for use in sold materials only, such as wood or metal.
• NEVER leave anything in the 3-in-1 Superyard that could provide a foothold or create a danger of suffocation or strangulation.
• When setting up as an enclosure an unlimited number of panels may be used. When setting up as a barrier, the maximum number of panels is twelve.

A. Screws
B. Panel
C. Wall Fi ng C
D. Gate Panel
E. Wall Fi ng A
F. Wall Fi ng B
G. Floor Spacer D
H. Template

To ensure safe operation, additional or replacement parts should be obtained only from North States or its authorized distributors. Contact inform on appears on the cover of these instructions. Replacement parts can be ordered at www.northstatesind.com Any damage to property during installion of your safety gate is the sole responsibility of the end user.

ENCLOSURE SETUP

Step 1: Unfold the 3-in-1 Superyard.
Step 2: Pos on and adjust the se ons to a hexagon. Turn se ons to align hexagonal mark with arrow on opposite hinge (see Figure 2).
Note : The Superyard should be placed on a flat surface.
Step 3 : Remove the ve al bars in both panels you wish to connect. Turn clockwise to loosen and pull down to remove.
Step 4: Remove the Socket Cap E. Note: Keep for future use as a barrier.
Step 5: To connect the panels together, ve ally li one panel allowing the upper and lower hinge housings to slip into place in the ma ng panel (See Figure 4).
Step 6: Insert the vertical bar into recess of lower hinge mount.} Press “A” down and slide it into upper hinge, as shown in Figure 5B.
Note : When set up as an enclosure, you will have one extra vertial bar.

Step 7: To secure gate as an enclosure, ten each ve al bar counter- clockwise (hand- ht). See Figure 5C.
Note : Loosen each ver l bar clockwise before folding the Superyard for storage. Properly set-up as an enclosure.

WALL MOUNTING

Step 1: Unfold the 3-in-1 Superyard. Step 2: Pos n the 3-in-1 Superyard to fit in your opening. Select the walls you wish to mount the hardware to.
Note : To accommodate different sized openings, you can add or remove an even number of panels. An addional hardware package is needed and can be purchased at www.northstatesind.com when using an odd number of panels.

Step 3: On the end panels, remove the vertical bars. Turn clockwise to loosen the vertical bar, then pull down to remove.
Note : To report on the panel with the door, simply follow the directions to set up the Superyard as an enclosure. Select and disconnect the two panels you desire to mount to the wall or surface.

Step 4: Pos on the template ve al to the floor and mark the screw holes. Mount the wall ngs A, B, C onto the wall with screws included.
Step 5: A ach floor spacer-D to lower hinge housing.

Step 6: Place panels on the mounted wall fittings, as shown in Figure 8A and 8B.
Step 7: Insert removable bars through wall fitting-C on both sides of gate, positoning the bars in lower hinge housing.
Step 8: Insert the vertical bars in the upper hinge housing and upper hinge holder, rota ng the handgrips un they are hand tight.
Step 9: To secure gate as a barrier, ten each ve al bar counter-clockwise (hand- ht). See Figure 10C.
Note : Loosen each vertical bar clockwise before folding the Superyard for storage.

STAY-OPEN FEATURE

IMPORTANT : Stay-Open Feature should be used only by adults, because the auto-close feature will be disabled allowing children to freely pass through the gate. To make use of the Stay-Open Feature, simply swing the door slightly past 90 degrees. The door will remain open until it is swung closed. See Figure 12.

Two-Panel Extensions sold separately.
Note : When setting up as an enclosure an unlimited number of panels may be used. When setting up as a barrier, the maximum number of panels is twelve.

TROUBLESHOOTING

If the gate does not stay closed, verify that the mark in the le upper corner of the gate is aligned with the mark on the upper locking housing, as shown in Figure 13C. If the mark on the le upper corner does not align with the mark on the upper locking housing, please make the adjustments below to ensure that the door panel can be auto closed. If the upper locking housing is offset toward the right (13A) or le (13B), please loosen the screw on upper locking housing , then adjust the door panel and upper locking housing un the two marks are aligned (13C). Make certain to re hten the screw (13D).

Note : Please use two screwdrivers when tening or loosening the screws (13D).

If the upper locking housing is misaligned upward (13E) or downward (13F), please loosen the screw on the door lower hinge (13G), then press the door panel and the door lower hinge together (13H) un the two marks on the le corner are aligned. Make sure the screw is retightened.

Care

CLEANING:
Clean the Superyard using warm water and a mild detergent. Use a so cloth or sponge to avoid scratches. Never use solvents or chemicals to clean the Superyard. DISCLAIMER:

Distributed exclusively in the United States by North States Industries, Inc.
5455 Highway 169 N
Plymouth, MN 55442
www.northstatesind.com
Manufactured in China

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>