north states 5455 MyPet Wide Walk Thru EasyPass Pet Gate Instruction Manual
- June 9, 2024
- north states
Table of Contents
north states 5455 MyPet Wide Walk Thru EasyPass Pet Gate Instruction Manual
www.northstatesind.com
CustomerService@northstatesind.com
IMPORTANT! READ AND FOLLOW THESE INSTRUCTIONS CAREFULLY AND KEEP FOR FUTURE REFERENCE
Important Safety Information
- Do not use the product if any components are broken or missing. If parts are required please contact our Customer Service Department (contact information on the first page). Do not use replacement parts other than those approved by the manufacturer or distributor. Non-approved spare parts may render the repair or the product unsafe. Replacement parts can be ordered at www.northstatesind.com
- Check regularly that all fittings and components are secure and that no components are worn, broken or missing.
- Check regularly that all fittings are securely tightened and that the locking mechanism is working properly.
- Any damage to property during installation of your safety gate is the sole responsibility of the end user.
- We recommend that you carry out the installation away from small children as some components may present a choking hazard when loose.
⚠ WARNING
- STOP using when a pet can climb over or dislodge the gate. · Install only with locking/latching mechanism securely engaged.
- To prevent falls, never use at top of stairs.
- This product will not necessarily prevent all accidents.
- NEVER leave pet unattended.
- This gate is to be used in openings 29.75″ to 37.5″ (75.56 cm to 95.25 cm). · Periodically check all fasteners to be sure they are tight and secure, stop using gate if any parts are missing or become damaged.
- A. Bolt
- B. Tension Knob
- C. Tape Pad
- D. Wall Cup
- E. Screw
- F. Extension
- G. Upper Extension Adapter
- H. Lower Extension Adapter
- I. Gate Frame
- J. Wrench
Read this first! Note: When you initially unpack your gate there is a gap
between the swinging door and gate frame.
This is not a defect. The gap will close once properly mounted.
Installation
Step 1
- Measure width of opening.
- Refer to Figures 1A, 1B, 1C to determine the correct installation.
Step 2
-
To add an extension, begin by removing both the upper and lower plugs from the side(s) of the gate frame. You may need to use a flathead screwdriver to remove the plugs (Figure 2A).
-
Attach both the upper and lower adapters to the extension pole.
-
Install the fully assembled extension by inserting the upper and
lower extension adapters into the gate in the holes where you removed the plugs (Figure 2B). -
Reinsert plug(s), then insert the bolts into the holes on the outside of the extension (Figure 2C).
IMPORTANT: Do not install two extensions on the same side of the gate.
Step 3
- To install wall cups, place the gate in the opening so that the bottom of the gate frame is completely flat on the floor (Figure 3A).
- Fasten the mounting cups to the wall by aligning them with the bolts. Use double coated tape or screws provided as shown in Figure 3B.
IMPORTANT: Never install this gate without mounting cups!
Step 4
- To mount your gate, place the gate where you want to install it, then extend all 4 bolts until they reach the walls. Ensure that the ends of the bolts are seated inside the mounting cups.
- Tighten both of the bottom tension knobs by turning them clockwise (Figure 4A).
- Tighten both of the upper tension knobs by turning them clockwise so that the gap between the gate and upper right corner comes together leaving 1.5 ~ 2 mm gap as shown in Figure 4B.
Note: When securing the gate in the opening, the distance between the gate frame and the opening should not exceed 2 ¾” on either side of the gate and the 4 tension bolts should be equal as shown in Figure 4D.
Operation
Opening the gate: Pull back the button on the top of the handle with your thumb, squeeze the trigger on the lower side of the handle, then lift the inner door up and open the door.
Closing the gate: Your gate has an easy-close feature. You can leave the gate in the open position and when ready, simply push the gate door closed until it clicks.
Note: Always check the handle, bottom swing guard and inner tabs to make sure that the gate is securely locked.
Pet Door Operation: Place fingers in the two designated openings found on either side of the paw prints on the small pet door. Squeeze and lift upward until the desired height is reached. The door will ‘click’ in place.
Note: This door will open at three height intervals: 5″, 6.5″, 8″. To close, simply reverse the process.
Swing Control Operation
Rotate the knob downward on the gate stopper to determine the direction the
gate door will swing. Gate opens in both directions when gate stopper is not
rotated. To fully lock, lower the gate stopper to the locked position on both
sides of the gate.
Care
CLEANING: Clean the safety gate using warm water and mild detergent. Use a soft cloth or sponge to avoid scratches. Never use solvents or chemicals to clean the safety gate.
Distributed exclusively in the United States by
North States Industries, Inc. 5455 Highway 169 N Plymouth, MN 55442
www.northstatesind.com Manufactured in China
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>