north states 4955 MyPet Windsor Walk-Thru Petgate Instructions

north states 4955 MyPet Windsor Walk-Thru Petgate

IMPORTANT: PLEASE KEEP FOR FUTURE REFERENCE!
For helpful tips and instructions, please visit our website: www.northstatesind.com or contact our Customer Care department via email: CustomerService@northstatesind.com Phone: 763-486-1754 or Toll Free: 800-848-8421

WARNING

• STOP using when a pet can climb over or dislodge the gate.
• Install only with locking/latching mechanism securely engaged.
• This product will not necessarily prevent all accidents.
• NEVER leave pet unattended.
• This gate is to be used in openings 28.68” to 47.85” (72.8 cm to 121.5 cm) only.
• Periodically check all fasteners to be sure they are tight and secure, stop using gate if any parts are missing or become damaged.
• Hardware is included for use in solid materials only, such as wood or metal.

Your safety gate contains the following

• A Mounting Screw
• B Hinge Screw
• C Hinge / Hinge Pin
• D Gate Frame
• E Upper Latch
• F Upper Latch Housing
• G Lower Latch
• H Lower Latch Housing
• I Wrench
• J Template

To ensure safe operation, additional or replacement parts should be obtained only from North States or its authorized distributors. Contact information appears on the cover of these instructions.
Any damage to property during installation of your safety gate is the sole responsibility of the end user.

Installation

• Step 1 Measure the width of your opening.

• Step 2 Unscrew and remove both the upper and lower assembly fittngs on the gate frame.

• Step 3 Set the appropriate width of the gate by overlapping the two frames to the extent necessary to allow room for the spindles on either side of the gate. The minimum allowable overlap is two bars. The maximum allowable overlap is seven bars.
  Note :The spindles are adjustable to accommodate the gap between the gate frame and the opening.

• Step 4 The assembly fittngs MUST be installed onto the gate frames to keep the gate secure. Secure the gate frames together by installing the upper and lower assembly fittngs onto the gate frame.

• Step 5 Note: Do not mount hardware into sheetrock or plaster. Hardware is included for use in solid materials only such as wood or metal.
  Hold template (A) against the surface to which the gate is to be fitted (hinge side). Ensure the template is vertical, completely outstretched and that the end marked ” is on the floor. Mark the screw hole positions.

• Step 6 Disconnect both the upper and lower hinges by sliding the top hinge pin/hinge apart. Secure the lower and upper hinges with the mounng screws with the post poinng upwards as shown.
  Note: Do not secure the top hinge with pin at this time.

• Step 7 Hold template (B) against the surface to which the gate is to be fitted (latch side). Follow the directions in step 5.

When using the gate at the top of the stairs, never allow the gate to swing over the stairs.
Note: Both the upper & lower latch housings have a raised edge. The raised edge should be installed on the side to which you do not want the gate to open. If you are not using this at the top of the stairs and would like the gate to swing in both directions, install both the upper and lower latches without the latch housings.

• Step 8 Secure both the upper latch and housing and the lower latch and housing with the mounting screws provided.

• Step 9 Place the upper and lower spindles of the gate frame on the upper and lower hinges. You may need to turn the spindles so it fits on the hinge.

• Step 10 Place the gate in the opening so that the distance A (hinge side) is min. 1.3″ (33mm) and max. 2.8” (72mm). The distance B(Iatch side) is min. 1.2″(30mm)and max. 2.8″ (72mm). Adjust the protrusion of the hinge side and latch side spindles by turning them so that the distance between the gate frame and the opening meet the required measurements.
  The upper and lower latch spindles must be engaged. Swing the gate closed to verify that the latch spindles secure into the upper and lower latches.

• Step 11 Connect both the upper and lower top hinges with pins to the lower hinges by lightly pressing downwards and secure them into place. Secure with the hinge screws.

• Step 12 Secure the locknut on the spindles with the wrench provided. The upper and lower latch spindles must be engaged in the latches.

Operation

Opening the gate

1.  Press the upper latch button downward with thumb.
2.  Lift the latch spindle out of the cup.
3. Push or pull the gate open.

Closing the gate

1.  Manually swing the gate closed.
2. Ensure both the upper and lower latch spindles are engaged in their respective cups.
3. Verify to ensure the gate is securely in its locked position.

Removal and reinstallation

Simply remove the hinge screws that secure the top of the hinge pin on both the upper and lower hinges. Insert a small bladed screwdriver in the screw hole and gently pull upward to disengage the hinge pins. Be sure to save the screws and hinge pins for future use.
Note: When reinstalling the gate, be certain to reinstall the hinge pins safely by following step 11.

CARE

CLEANING: Clean the safety gate using warm water and a mild detergent. Use a soft cloth or sponge to avoid scratches. Never use solvents or chemicals to clean the safety gate.

Distributed exclusively in the United States by North States Industries, Inc.
5455 Highway 169 N Plymouth, MN 55442
www.northstatesind.com
Manufactured in China

References

• North States Industries

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>