north states 8657 6 Panel Petyard Passage Instructions
- June 6, 2024
- north states
Table of Contents
north states 8657 6 Panel Petyard Passage
IMPORTANT: PLEASE KEEP FOR FUTURE REFERENCE!
For helpful tips and instructions, please visit our website:
www.northstatesind.com or contact our
Customer Care department via email:
CustomerService@northstatesind.com
Phone: 763-486-1756 or Toll Free:
800-848-8421
- Children have died or been seriously injured when enclosures are not securely installed.
- ALWAYS install and use enclosure as directed using all required parts.
- STOP using when a child can climb over yard or dislodge/open the enclosure.
- This product will not necessarily prevent all accidents.
- NEVER leave child unattended.
- NEVER use to keep child away from pool.
- Use only with the locking/latching mechanism securely engaged.
- When child is present, always keep the pet door in the locked position.
- This product intended for use with children from 6 months up to 24 months of age.
- Periodically check all fasteners to be sure they are tight and secure, stop using this enclosure if any parts become damaged.
- Do not use this product on a smooth slippery surface unless skid-resistant pads are used (included)
- Do not attempt to use this enclosure in temperatures less than 40 degrees F, or damage may result.
- Do not use as a barrier for stairways, stoves or heaters.
- Do not use on uneven surface.
- Do not connect more than 8 panels in one enclosure
A. Enclosure
B. Carry Strap
C. Skid-Resistant Pads
Note: Model 8799 comes with 16 skid-resistant pads and Model 8807 comes
with 8.
To ensure safe operation, additional or replacement parts should be obtained
only from North States or its authorized distributors. Contact information
appears on the cover of these instructions. Replacement parts can be ordered
at http://northstatesind.com/main/shop-parts/
Any damage to property during installation of your enclosure is the sole
responsibility of the end user.
PROPER SET-UP CONFIGURATIONS
We recommend that you use your Petyard only as an enclosure, not as a barrier.
See FIGURE 1 for proper configuration
SET-UP INSTRUCTIONS
Begin setting up your enclosure by unsnapping the gray carrying strap and carefully unfolding the panels to the proper configuration on page 2. (NOTE: Model 8799 consists of eight panels which will form an octagon when set up properly. Model 8807 consists of four panels which form a square.)
When you have finished unfolding the panels, there will be two unconnected panels arranged, as shown in FIGURE 2. Make certain that the pin in cylinder B is up as shown.
Begin connecting the panels together by gently lifting up on panel 2 and setting the opening “A” (as shown in FIGURE 3) over pin “B” located on panel
Now locate the slot on the lower end of cylinder “D”, as shown in FIGURE 4. This slot tapers to an opening that accommodates pin “C”.
Gently press down on panel 2 while aligning pin “C” with the slot in cylinder
“D”. While maintaining downward pressure on panel 2, lift slightly on panel 1,
and slide pin “C” through the slot and into the opening as shown
EXTENSION INSTALLATION
EXTENSION INSTALLATION Some models have two-panel extensions that are colored appropriately for your yard and are available either from your retailer or direct from www.northstatesind.com
The extension contains two additional panels that enable you to expand the size of your enclosure from 18.5 square feet to 34.4 square feet.
The extension is installed by following the “SET-UP INSTRUCTIONS” that appear above.
INSTRUCTIONS FOR INSTALLING SKID-RESISTANT PADS
Your North States enclosure can now be used on hard surfaces (hardwood floors, tile, linoleum, etc.) by installing the enclosed skid-resistant pads.
- Ensure that the surface of the yard panel is clean and dry prior to installing the pads.
- Remove a single pad from the release paper as shown in FIGURE 5.
- Place the adhesive side of the pad on the bottom edge of the yard panel approximately 2″ from the center of each hinge, as shown in FIGURE 6.
- Repeat steps 2 & 3 for each of the remaining pads.
- Maximum skid-resistance will be maintained by cleaning the bottoms of the pads periodically with a water-dampened clean cloth.
PET DOOR OPERATION
Your enclosure comes from the factory with the pet door in the “LOCKED” POSITION (See FIGURE 7).
TO UNLOCK
Squeeze and twist the front center knob located below the pet door. As you twist, the knob will line up with the arrows on the right or left sides of the knob. The pet door will move freely in both directions for your pet to pass through.
TO LOCK
Squeeze and twist the front center knob located below the pet door. As you
twist, the knob will be in the upright position, keeping the door securely
locked.
WARNING
Make certain that the pet door is securely locked in the closed position if
using with a child 6-24 months of age.
TO DISCONNECT PANELS
To disconnect two adjoining panels, select one of the joints where the panel pushes down (panel 1), as shown in FIGURE 8.
Gently press down on panel 1 while lifting slightly on panel 2. This will
enable you to slide pin “C” free of cylinder “D” (see FIGURE 4). Then lift up
on panel 1 until opening “A” (see FIGURE 3) is free of pin “B”.
FOLDING FOR TRANSPORT OR STORAGE
Your enclosure folds compactly for transport or storage. You must, however, fold the panels properly. Disassembly and folding is accomplished by first following the “DISCONNECT PANELS” instructions above.
Gently fold the panels (without jerking them or slamming them together) in alternating directions like an accordion. FIGURE 9 illustrates the configuration of a properly folded yard.FIGURE 9
Slip one end of the gray carrying strap through the mesh near the top middle
of each outside panel and snap it closed. The enclosure is now ready for
transport or storage.
CLEANING INSTRUCTIONS
Your enclosure is manufactured from durable, weather-resistant plastic panels. To clean, wash the panels with mild, non-abrasive detergent, rinse with clean water, and allow to dry thoroughly.
REPLACING A PANEL
A broken panel can easily be replaced by obtaining one from the manufacturer at http://northstatesind/main/shop-parts/
Remove the broken panel by following the “TO DISCONNECT PANELS” instructions (above). Install the replacement panel by following the “SET-UP INSTRUCTIONS” check above
Documents / Resources
|
north states 8657 6 Panel Petyard
Passage
[pdf] Instructions
8657, 8799, 8807, 8657 6 Panel Petyard Passage, 6 Panel Petyard Passage,
Petyard Passage
---|---
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>