infineon CY8CKIT-062S4 PSoC 62S4 Pioneer Kit User Guide

infineon CY8CKIT-062S4 PSoC 62S4 Pioneer Kit

CY8CKIT-062S4

The PSoCTM 62S4 pioneer kit (CY8CKIT-062S4) is a low-cost hardware platform that enables you to design and debug applications using the PSoC 62 MCU.

Kit contents

• > PSoC 62S4 pioneer board
• > USB type-A to micro-B cable
• > Six jumper wires (five inches each)
• > Quick start guide (this document)

PSoC 62S4 pioneer board details

1. KitProg3 status LED (D10)
2. KitProg3 USB connector (J10)
3. PSoC 5LP programming header (J7)*
4. 2.5 V selection jumper (J14)
5. PSoC 6 MCU power selection jumper (J12)
6. PSoC 5LP based KitProg3 programmer and debugger (CY8C5868LTI-LP039, U7)
7. PSoC 6 MCU current measurement jumper (J13)
8. KitProg3 programming mode selection button (SW3)
9. Power LED (D14)
10. PSoC 6 MCU reset button (SW1)
11. Arduino™ UNO R3 compatible power header (J1)
12. PSoC 6 MCU 10-pin SWD/JTAG program and debug header (J8)
13. User LEDs (D12 and D13)
14. Arduino UNO R3 compatible I/O headers (J2, J3 and J4)
15. PSoC 6 MCU user button/hibernate wakeup (SW2)
16. PSoC 6 MCU (CY8C6244LQI-S4D92, U8)
17. CapSense™ buttons and slider (CSB1, CSB2 and CSS1)
18. Thermistor (TH1)
19. Ambient light sensor (Q8)
20. QSPI NOR flash (S25FL512SAGMFIR10, U9)
21. PSoC 6 MCU USB connector (J5)
22. PSoC 6 MCU extended I/O header (J11)*
23. External power supply connector (J9)*

* Footprint only, not populated on the board

https://www.cypress.com/CY8CKIT-062S4

Before you start

• › Ensure that you have the following:
  • PC with USB port
  • UART terminal software such as Tera Term or Minicom

• › Visit the kit website to download and install the required software.

• › Ensure the jumper J12 is at position 2-3 to select 3.3 V.

• › Connect the KitProg3 USB connector (J10) to your PC.

• › Wait for the driver installation to complete.

Step 1: Connect the kit with UART terminal software

• › Open the UART terminal software and connect to the kit’s USB-UART COM port with the following settings:
  • Baud rate: 115200 bps
  • Data: 8 bit
  • Parity: None
  • Stop bit: 1 bit
  • Flow control: None

• › Press the XRES switch (SW1) to reset the device.

Step 2: Run the pre-programmed code example

• › Follow the instructions displayed on the UART terminal to use the pre-programmed code example.

Step 3: Observe the user LED (D13) brightness variation

• › Observe the state of the user LED (D13) with the variation of ambient light intensity. The LED turns ON when the ambient light intensity is lower than 45% and turns OFF when higher than 55%.

Document Number: 002-30749 Rev. *C
All rights reserved. © 2021 Infineon Technologies AG

Documents / Resources

| infineon CY8CKIT-062S4 PSoC 62S4 Pioneer Kit [pdf] User Guide
CY8CKIT-062S4, PSoC 62S4 Pioneer Kit, CY8CKIT-062S4 PSoC 62S4 Pioneer Kit, Pioneer Kit
---|---

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>