allen roth Avalyn Carat Flush User Manual
- June 6, 2024
- Allen+Roth
Table of Contents
ITEM #2806776
Avalyn Carat™ Flush
MODEL #2889556 Black A &R
#2889557 Gold A &R
ALLEN+ROTH and logo designs are trademarks or registered trademarks of LF,
LLC. All rights reserved.
ATTACH YOUR RECEIPT HERE
Serial Number
Purchase Date
Questions, problems, missing parts? Before returning to your retailer,
call our customer service department at
1-866-439-9800, 8 a.m. – 8 p.m., EST,
Monday – Sunday. You could also contact us at
partsplus@lowes.com or visit
www.lowespartsplus.com.
PACKAGE CONTENTS
| PART | DESCRIPTION | QUANTITY |
|---|---|---|
| A | Mounting bracket | 1 |
| B | LED ceiling light | 1 |
HARDWARE CONTENTS
****SAFETY INFORMATION
Please read and understand this entire manual before attempting to assemble,
operate or install this product.
WARNING
-
Risk of electrical shock. Switch off the main electrical supply from the fuse box/circuit breaker before installing the unit or doing any maintenance.
-
Do not use outdoor.
USA (FCC) -
Changes or modifications to this unit not expressly approved by the party responsible for compliance could
void the user’s authority to operate the equipment. -
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
1. This device may not cause harmful interference, and
2. This device must accept any interference received, including interference that may cause undesired operation.
NOTICE
This equipment has been tested and found to comply with the limits for Class B
digital devices, pursuant to part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses, and can radiate
radio frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio or television reception.
However, there is no guarantee that interference will not occur in an
installation. If this equipment causes harmful interference to radio or
television reception, which can be determined by turning the equipment off and
on, the user is encouraged to try to correct the interference by one or more
of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and the receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
Canada IC
Operation is subject to the following two conditions:
- this device may not cause interference, and
- this device must accept any interference, including interference that may cause undesired operation of the device.
CAUTION
- If using a dimmer, it must be LED compatible.
IMPORTANT
The installer and/or user must read, understand and follow these instructions
before installing the product.
This product must be properly installed before it is used. If instructions are
not followed, the manufacturer will not be held responsible for any problems
or product malfunction. Failure to follow installation and/or operating
instructions voids the warranty. We recommend that this product be installed
by a certified electrician. In some states or provinces, it is a legal
requirement for this type of product to be installed by a certified
electrician, according to the electrical and building codes effective in the
region where the unit is used.
KEEP THESE INSTRUCTIONS FOR FUTURE REFERENCE.
PREPARATION
Before beginning the installation of the product, make sure all parts are
present. Compare parts with package contents list and hardware contents list.
If any part is missing or damaged, do not attempt to install the product.
Estimated Installation Time: 30 minutes.
Tools Required for Installation (not included): pencil, screwdriver, drill,
1/4 in drill bit (6.5 mm).
MOUNTING BRACKET INSTALLATION
1. Center and place the mounting bracket (A) over the existing junction box
opening. Mark all four screw hole locations. Make sure mounting bracket (A) is
oriented as shown.
2. After removing the
mounting bracket, drill a 1/4 in. hole at each marked location. Next, install
a wall anchor (AA) in each hole location.
Hardware Used
MOUNTING BRACKET AND FINAL INSTALLATION
3. Replace mounting bracket (A) and secure with four mounting bracket screws
(BB).
Hardware Used
4. Secure mounting bracket (A) to the junction box with two junction box
screws (CC).
Hardware Used
5. Clip LED ceiling light (B) to mounting bracket (A) and then connect the
wiring as shown (white, black and ground). Secure
connections with a wire connector (DD). Place LED ceiling light (B) over
mounting bracket flanges.
Hardware Used
6. Secure LED ceiling light (B) with four canopy screws (EE). Make sure all
wiring and wiring connectors fit inside the LED ceiling light (B) base.
Hardware Used
CARE AND MAINTENANCE
- Ensure power is off before cleaning. Clean with a mild glass cleaner and a soft cloth. Apply liquid cleaner to cloth. Do not spray the fixture itself.
- Do not attempt to replace LEDs.
WARRANTY
This product is covered by a three (3) year limited warranty on manufacturing
defects from the date of purchase for residential use only. If within this
period the product is found to be defective in material or workmanship,
contact our customer service department at
1-866-439-9800. The warranty is
extended to the original owner in USA and Canada and is non-transferable. This
warranty is valid only on products installed in accordance with the building
code and laws effective in the region where the unit is used as well as in
accordance with the provided instruction manual. It does not cover products
installed incorrectly or subjected to abnormal use. The warranty does not
cover handling, labor, transportation, or any other cost associated with the
installation or replacement of the product. This limited warranty is valid in
the country of purchase only. The manufacturer will not be held responsible
for any direct or consequential damages or injuries related to the use of this
product arising from improper use or installation of this product.