PHILIPS DALI-2 Driver Controller Owner’s Manual
- July 31, 2024
- Philips
Table of Contents
PHILIPS DALI-2 Driver Controller
Specifications:
- Model : DDBC320-DALI
- Type : DALI-2 Driver Controller
- Dimensions : 216 mm x 104 mm x 64 mm
- Load Type : Electronic Driver Pilot Duty Inrush Current
- Output Ratings/Channel (CH): CH1-CH3 – 16 A, 277 V; 20 A, 240 V
- Output Ratings/Group: CH-CH < 500 V DDBC320-DALI 60A
- Control Channel Ratings: DALI 64/Universe, Address-Guaranteed 220 mA, Maximum 250 mA
Product Usage Instructions
-
Installation:
Devices must be installed in an approved enclosure by a qualified electrician following all national and local electrical and construction codes and regulations. -
Control Channel Setup:
Connect the input and output of each channel as labeled (CH1 IN OUT, CH2 IN OUT, CH3 IN OUT). -
DALI Connection:
Connect DALI devices accordingly (DALI 1 DALI 2 DALI 3 DA- DA+ DA- DA+ DA- DA+). -
Service Switch:
Use the service switch to toggle between Service mode and DALI LED modes. -
Safety Precautions:
Always follow basic safety precautions when using electrical equipment. Ensure all safety instructions are read and followed.
Devices must be installed in an approved enclosure by a qualified electrician in accordance with all national and local electrical and construction codes and regulations.
WARNING INSTRUCTIONS
DIMENSION
Installation
IMPORTANT SAFEGUARDS
When using electrical equipment, basic safety precautions should always be followed including the following:
READ AND FOLLOW ALL
SAFETY INSTRUCTIONS
- Do not use outdoors
- Do not use this equipment for other than the intended use.
SAVE THESE INSTRUCTIONS
Caution
- DALI wires are NOT SELV and should never be considered touch-safe. Basic insulation or higher is required between DALI wires and mains cabling.
- Any modifications not approved by the manufacturer of this device could void the user’s authority to operate this device.
FCC and RSS-210 of IC (Industry Canada) Rules
This equipment has been tested and found to comply with the limits for a Class
B digital device, pursuant to part 15 of the FCC Rules and pursuant to RSS210
of the IC Rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation. This equipment
generates, uses, and can radiate radio frequency energy and, if not installed
and used in accordance with the instructions, may cause harmful interference
to radio communications. However, there is no guarantee that interference will
not occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures: Reorient or relocate
the receiving antenna. Increase the separation between the equipment and the
receiver. Connect the equipment to an outlet on a circuit different from that
to which the receiver is connected. Consult the dealer or an experienced
radio/TV technician for help. Any modifications not approved by the
manufacturer of this device could void the user’s authority to operate this
device.
This Class B digital apparatus complies with Canadian ICES-003: CAN ICES-3(B)/NMB-3(B). Cet appareil numerique de la Classe B est conforme a la norme NMB-003 du Canada: CAN ICES-3(B)/NMB-3(B).
Installation of a home and building automation and control system shall comply with IEC 60364 (all parts). The temperature limits and current-carrying capacities for the communication wires specified in IEC 60364-5-52 shall not be exceeded.
© 2024 Signify Holding. All rights reserved. Specifications are subject to change without notice. No representation or warranty as to the accuracy or completeness of the information included herein is given and any liability for any action in reliance thereon is disclaimed. Philips and the Philips Shield Emblem are registered trademarks of Koninklijke Philips N.V. All other trademarks are owned by Signify Holding or their respective owners.
FAQ
Q: What are the temperature limits for communication wires specified in IEC
60364-5-52?
A: The temperature limits and current-carrying capacities for communication
wires specified in IEC 60364-5-52 should not be exceeded during installation.
Q: Where can I find more information about the product?
A: For more information, visit www.dynalite.com or
refer to the user manual provided with the product.
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>