VigilLink VLSP-12HT150 18Gbps 1×2 HDMI Over HDBaseT Extender User Manual
- June 6, 2024
- VigilLink
Table of Contents
- VigilLink VLSP-12HT150 18Gbps 1×2 HDMI Over HDBaseT Extender User Manual
- Tha nk you for purchas ing t his product
- A surge prot ect ion device is recommended.
- Caution
- Introduction
- Features
- Package Contents
- Specifications
- Operation Controls and Functions
- Transmitt er
- Rear Panel
- HDBa s e T Receiver
- IR Pin Definition
- EDID Mode
- ASCII Commands
- Application Example
- Read More About This Manual & Download PDF::
- Read User Manual Online (PDF format)
- Download This Manual (PDF format)
VigilLink VLSP-12HT150 18Gbps 1×2 HDMI Over HDBaseT Extender User Manual
Tha nk you for purchas ing t his product
For optimum performance and safety, please read these instructions carefully before connecting, operating, or adjusting this product. Please keep this manual for future reference.
A surge prot ect ion device is recommended.
This product contains sensitive electrical components that may be damaged by electrical spikes, surges, electric shocks, lightning strikes, etc. The use of surge protection systems is highly recommended to protect and extend the life of your equipment.
Caution
The product requires the use of UTP connectors. Please connect in directinterconnection method and do not cross connect.
Introduction
This 18Gbps HDMI 1×2 HDBaseT Splitter can distribute 1 source signal to any 2 display devices, with video resolution up to 4K2K@60Hz 4:4:4. It is designed with 1 HDMI loop output and 2 HDBaseT outputs. The HDMI signal transmission distance can be extended up to 394ft/120m at the resolution of 4K2K@60Hz, or 492ft/150m at 1080P@60Hz via a single CAT6/6a/7 cable. The product supports up to 7.1CH HD audio pass- through. It also supports IR and RS-232 signal pass- through, audio de- embedding function and advanced EDID management.
Features
☆ HDMI 2.0b, HDCP 2.2 and HDCP 1.x compliant
☆ Support 18Gbps video bandwidth
☆ Support video resolution up to 4K2K@60Hz 4:4:4
☆ Support HDR, HDR10+, HLG and Dolby vision
☆ Support up to 7.1CH HD audio pass-through
☆ Support digital and analog audio de-embedded output
☆ Extend the signal transmission distance up to 394ft/120m at the resolution
of 4K2K@60Hz, 492ft/150m at 1080P@60Hz via a single CAT6/6a/7 cable
☆ Support 1 HDMI input, 1 HDMI loop output and 2 HDBaseT outputs.
☆ IR, RS-232 routed to HDBaseT output
☆ Advanced EDID management
☆ Support one-way POC function (only from transmitter to receiver)
☆ Compact design for easy and flexible installation
Package Contents
① 1 × 18Gbps HDMI 1×2 HDBaseT Splitter
② 2 × HDBaseT Receiver
③ 3 × IR Blaster Cable (1.5 meters)
④ 3 × 20K~60KHz IR Receiver Cable (1.5 meters)
⑤ 3 × 3pin-3.81mm Phoenix Connector (male)
⑥ 1 × 5pin-3.81mm Phoenix Connector (male)
⑦ 6 × Mounting Ear
⑧ 1 × 24V/1A DC Locking Power Adapter
⑨ 12 × Machine Screws (KM3*4)
⑩ 1 × User Manual
Specifications
Technical
HDMI Compliance| HDMI 2.0b
HDCP Compliance| HDCP 2.2/1.x
Video Bandwidth| 594MHz/18Gbps
Video Resolution| Up to 4k2k@60Hz 4:4:4
Color Depth
| 8-bit,10-bit,12-bit (1080p@60Hz) 8-bit (4K2K@60Hz YUV4:4:4)
8-bit,10-bit,12-bit (4K2K@60Hz YCbCr 4:2:2/4:2:0)
Color Space| RGB 4:4:4, YCbCr 4:4:4 / 4:2:2 / 4:2:0
HDR| Support HDR, HDR10+, HLG, Dolby vision
( Note: For Dolby vision, the local HDMI loopout supports 4K60, but the remote HDMI output only supports 1080P. )
HDMI Audio Formats
| LPCM 2.0/2.1/5.1/6.1/7.1, Dolby Digital, Dolby TrueHD, Dolby Digital Plus
(DD+), DTS-ES, DTS HD Master, DTS HD-HRA, DTS-X
Coaxial Audio Formats| PCM2.0, Dolby Digital / Plus, DTS 2.0/5.1
Analog Audio Formats| PCM 2.0CH
ESD Protection| Human body model—±8kV (Air-gap discharge) &
±4kV (Contact discharge)
Connection
Transmitter
| Input: 1 x HDMI IN [Type A, 19-pin female]
Output: 1 x HDMI LOOP OUT [Type A, 19-pin female] 2 x HDBT OUTPUT [RJ45]
1 x COAX AUDIO OUT [RCA]
1 x L/R AUDIO OUT [5-pin phoenix connector] Control: 1 x RS-232 [3-pin phoenix connector]
1 x EDID DIP switch [5-pin]
1 x IR IN [3.5mm stereo mini-jack]
| 1 x IR OUT [3.5mm stereo mini-jack] |
|---|
Receiver
| Input: 1x HDBT IN [RJ45, 8-pin female] Output: 1x HDMI Type A [19-pin female]
1x AUDIO OUT [3.5mm Stereo Mini-jack] Control: 1x IR IN [3.5mm Stereo Mini- jack]
1x IR OUT [3.5mm Stereo Mini-jack] 1x RS-232 [Phoenix jack]
1x SERVICE [Mini-USB, Update port]
Mechanical
Housing| Metal Enclosure
Silkscreen Color| Black
Dimensions| Transmitter: 170mm (W) × 130mm (D) × 40mm (H) Receiver: 140mm (W)
× 65mm (D) × 18mm (H)
Weight| Transmitter: 689g Receiver: 155g
Power Supply| Input: AC100 – 240V 50/60Hz, Output: DC 24V/1A (US/EU standards,
CE/FCC/UL certified)
Power Consumption| 18W (Max)
Operation
Temperature
| 0°C ~ 40°C / 32°F ~ 104°F
Storage Temperature| -20°C ~ 60°C / -4°F ~ 140°F
Relative Humidity| 20~90% RH (non-condensing)
Operation Controls and Functions
Transmitt er
Front Panel
| No. | Name | Function Description |
|---|---|---|
| 1 | POWER LED | When the device is powered on, the red power LED will be on. |
| 2 | IN LED | When the HDMI IN port connects to an active source device, the |
green LED will be on.
3| LOOP LED| When the HDMI LOOP OUT port connects to an active display device,
the green LED will be on.
4| OUT (1~2) LED| When the HDBT OUTPUT 1/2 port connects an HDBaseT Receiver,
the corresponding green OUT LED
will be on.
Rear Panel
| No. | Name | Function Description |
|---|
1
| ****
RS-232
| Connect to a PC or control system via a 3-pin phoenix connector cable for three functions:
1, Firmware update;
2, Control the Splitter via RS-232 commands;
3, RS-232 signal pass-through (from transmitter to receiver or from receiver to the transmitter).
2| IR IN| Connect to the IR receiver cable, the IR receive signal will emit to the “IR OUT” port of the HDBaseT
Receiver.
3| IR OUT| Connect to the IR blaster cable, the IR emit signal is from the “IR
IN” port of the HDBaseT Receiver.
4| AUDIO OUT (COAX, L/R)| Coaxial/balanced audio output port, connect to
amplifier or speaker.
5| POWER switch| Press this switch to power on/off the device.
6| EDID DIP
switch
| Used to set EDID mode. Please refer to Section “6. EDID Mode” for details.
---|---|---
7
| ****
HDMI port
| IN: HDMI input port, connect to HDMI source devices such as DVD or set-top
box with an HDMI cable.
LOOP OUT: HDMI loop output port, connect to the HDMI display device such as a
TV or Monitor with an HDMI cable.
8| HDBT OUTPUT
port (1~2)
| Connect to the HDBT IN port of the HDBaseT receiver with a CAT cable.
9
| ****
Link Signal Indicator lamp (Green)
| ▪ Illuminating: Transmitter and Receiver are in good connection status.
▪ Flashing: Transmitter and Receiver are in poor connection status.
▪ Dark: Transmitter and Receiver are not connected.
10
| Data Signal Indicator lamp (Orange)| ▪ Illuminating: HDMI signal with HDCP.
▪ Flashing: HDMI signal without HDCP.
▪ Dark: No HDMI signal.
11
| ****
DC 24V
| Plug the DC 24V power supply into the unit and connect the adaptor to an AC outlet. ( Note: The transmitter can power the receiver via a CAT cable.)
HDBa s e T Receiver
| No. | Name | Function Description |
|---|---|---|
| 1 | Power LED | When the receiver is powered on, the power indicator will be on. |
| 2 | SERVICE port | Used for firmware update. |
3
| ****
DC 24V
| Plug DC 24V/1A power supply into the unit and connect the adapter to an AC outlet.
( Note: The HDBaseT receiver also can be powered by the transmitter via a CAT cable.)
---|---|---
4| HDBT IN| Connect to the HDBT OUTPUT port on the transmitter
with a CAT cable.
5
| ****
Link Signal Indicator lamp (Green)
| ▪ Illuminating: Transmitter and Receiver are in good connection status.
▪ Flashing: Transmitter and Receiver are in poor connection status.
▪ Dark: Transmitter and Receiver are not connected.
6
| Data Signal Indicator lamp (Orange)| ▪ Illuminating: HDMI signal with HDCP.
▪ Flashing: HDMI signal without HDCP.
▪ Dark: No HDMI signal.
7| HDMI OUT| HDMI output port, connect to HDMI display device such as TV or
Projector with an HDMI cable.
8| AUDIO OUT| HDMI output port, connected to HDMI display device such as TV or
Projector with an HDMI cable.
9| IR IN| Audio output port, connect to audio amplifier or speaker.
10| IR OUT| Connect the IR blaster cable, the IR signal is from the IR IN port
of the transmitter.
11
| ****
RS-232
| 3-pin Phoenix connector for RS-232 command transmission. The RS-232 command will pass-through from transmitter to receiver or from receiver to
transmitter.
IR Pin Definition
Note: When the angle between the IR receiver and the remote control is ± 45 °, the transmission distance is 0-5 meters; when the angle between the IR receiver and the remote control is ± 90 °, the transmission distance is 0-8 meters.
EDID Mode
The defined EDID setting list of the product is shown below:
| EDID Mode | EDID Description |
|---|---|
| 11111 | 1080P, Stereo Audio 2.0 |
| 11110 | 1080P, Dolby/DTS 5.1 |
| 11101 | 1080P, HD Audio 7.1 |
| 11100 | 1080I, Stereo Audio 2.0 |
| 11011 | 1080I, Dolby/DTS 5.1 |
| 11010 | 1080I, HD Audio 7.1 |
| 11001 | 1080P 3D, Stereo Audio 2.0 |
| 11000 | 1080P 3D, Dolby/DTS 5.1 |
| 10111 | 1080P 3D, HD Audio 7.1 |
| 10110 | 4K2K30Hz_444, Stereo Audio 2.0 |
| 10101 | 4K2K30Hz_444, Dolby/DTS 5.1 |
| 10100 | 4K2K30Hz_444, HD Audio 7.1 |
| 10011 | 4K2K60Hz_420, Stereo Audio 2.0 |
| 10010 | 4K2K60Hz_420, Dolby/DTS 5.1 |
| 10001 | 4K2K60Hz_420, HD Audio 7.1 |
| 10000 | 4K2K60Hz_444, Stereo Audio 2.0 |
| 01111 | 4K2K60Hz_444, Dolby/DTS 5.1 |
| 01110 | 4K2K60Hz_444, HD Audio 7.1 |
| 01101 | 4K2K60Hz_444, Stereo Audio 2.0 HDR |
| 01100 | 4K2K60Hz_444, Dolby/DTS 5.1 HDR |
| 01011 | 4K2K60Hz_444, HD Audio 7.1HDR |
| 01010 | COPY_FROM_LOOP OUT |
| 01001 | COPY_FROM_HDBT OUT1 |
| 01000 | COPY_FROM_HDBT OUT2 |
| 00111 | COPY_FROM_HDBT OUT3 |
| 00110 | COPY_FROM_HDBT OUT4 |
| 00101 | 1080P, Stereo Audio 2.0 |
| 00100 | 1080P, Stereo Audio 2.0 |
| 00011 | 1080P, Stereo Audio 2.0 |
| 00010 | 1080P, Stereo Audio 2.0 |
| 00001 | 1080P, Stereo Audio 2.0 |
| 00000 | PC control mode |
ASCII Commands
The product also supports ASCII command control. Connect the RS-232 port of the product to a PC with a 3-pin phoenix connector cable. Then, open a Serial Command tool on a PC to send ASCII commands to control the product. The ASCII command list about the product is shown below.
ASCII Commands
Serial port protocol. Baud rate: 115200, Data bits: 8bit, Stop bits:1, Check
bit: 0
x – Parameter 1 y – Parameter 2
! – Delimiter
Command Code| Function Description| Example| Feedback|
Default Setting
Power
s power z!
|
Power on/off the device,z=0~1 (z=0 power off, z=1 power on)
|
s power 1!
| Power on
System Initializing… Initialization Finished! FW version x.xx.xx
|
power on
r power!| Get the current power state| r power!| power on/power off|
s reboot!
|
Reboot the device
|
s reboot!
| Reboot…
System Initializing…
Initialization Finished! FW version x.xx.xx
|
System Setup
help!| List all commands| help!| |
r type!| Get device model| r type!| HDC-SPB14H150|
r status!
|
Get the device’s current status
|
r status!
| Get the unit all status power,
in/out connection, edid mode
|
r fw version!| Get Firmware version| r fw version!| MCU BOOT: Vx.xx.xx MCU
APP: Vx.xx.xx|
r link in!| Get the connection status of the input port| r link in!| HDMI IN:
connect|
r link out y!
| Get the connection status of the y output port, y=0~5(0=all, 1~4=HDBT 1~4, 5 = loop out)|
r link out 1!
| HDMI loop out:
connect
heat output 1: connect
|
s reset!
|
Reset to factory defaults
|
s reset!
| Reset to factory defaults
System Initializing… Initialization Finished!
FW version x.xx.xx
|
Command Code| Function Description| Example| Feedback|
Default Setting
---|---|---|---|---
Output Setting
s HDMI stream z!
| Set HDMI loop output stream on/off z=0~1(0: disable,1: enable)|
s HDMI stream 1!
| Enable HDMI loop out a stream Disable HDMI loop out
stream
|
enable
s HDMI HDCP z!
| Set HDMI loop output HDCP on/ off
z=0~1(0: disable,1: enable)
|
s HDMI HDCP 1!
| Enable HDMI loop out HDCP Disable HDMI loop out
HDCP
|
enable
s HDBT y HDCP
z!
|
Set HDBT output y HDCP on/off, y=0~4(0=all) z=0~1(0: disable, 1: enable)
|
s HDBT 1 HDCP 1!
s HDBT 0 HDCP 1!
| Enable HDBT output 1
HDCP
Disable HDBT output 1 HDCP Enable HDBT all outputs HDCP Disable HDBT all
outputs HDCP
|
enable
s HDBT y stream z!
|
Set HDBT output y stream on/ off, y=0~4(0=all) z=0~1 (0: disable,1: enable)
|
s HDBT 1
stream 1!
s HDBT 0
stream 1!
| Enable HDBT output 1 stream Disable HDBT output 1 stream Enable
HDBT all output streams Disable HDBT all outputs
stream
|
enable
r HDMI stream!| Get HDMI loop out stream status| r HDMI stream!| Enable HDMI
output stream|
r HDMI HDCP!| Get HDMI loop out HDCP status| r HDMI HDCP!| Enable HDMI output
HDCP|
r HDBT y HDCP!| Get HDBT output y HDCP status,
y=0~4(0=all)
| r HDBT 1 HDCP!| Enable HDBT output 1 HDCP|
r HDBT stream!| Get HDBT output y stream status, y=0~4(0=all)| r HDBT 1
stream!
| Enable HDBT output 1 stream|
Command Code| Function Description| Example| Feedback|
Default Setting
---|---|---|---|---
EDID Setting
s edid in from z!
| Set input EDID from the default|
s edid in from 1!
| |
1080p, Stereo Audio 2.0
EDID z, z=1~27|
1, 1080p,Stereo Audio 2.0|
2, 1080p,Dolby/DTS 5.1|
3, 1080p,HD Audio 7.1|
4, 1080i,Stereo Audio 2.0|
5, 1080i,Dolby/DTS 5.1|
6, 1080i,HD Audio 7.1|
7, 3D,Stereo Audio 2.0|
8, 3D,Dolby/DTS 5.1|
9, 3D, HD Audio 7.1|
10, 4K2K30_444,|
Stereo Audio 2.0|
11, 4K2K30_444,Dolby/DTS
5.1
12, 4K2K30_444,HD Audio
7.1
|
input EDID:1080p,
13, 4K2K60_420,| Stereo Audio 2.0
Stereo Audio 2.0 14, 4K2K60_420,
Dolby/DTS 5.1
|
15, 4K2K60_420,HD Audio
7.1
|
16, 4K2K60_444,| Please toggle EDID
Stereo Audio 2.0| dip switch to 00000!
17, 4K2K60_444,
Dolby/DTS 5.1|
18, 4K2K60_444,HD Audio
7.1
|
19, 4K2K60_444,|
Stereo Audio 2.0 HDR|
20, 4K2K60_444,|
Dolby/DTS 5.1 HDR|
21, 4K2K60_444,|
HD Audio 7.1 HDR|
22, copy from HDMI loop out|
23, copy from HDBT output 1|
24, copy from HDBT output 2|
25, copy from HDBT output 3|
26, copy from HDBT output 4|
27, use user1 EDID|
s edid user1 00 FF FF FF FF …!| Set user1 EDID data| s edid user1 00 ff ff ff
ff ….!| user1 EDID data: 00
FF FF ….
|
r edid user1!
|
Get user1 EDID data
|
r edid user1!
| user1 EDID data
: 00 FF FF FF FF FF FF
00 ………
|
---|---|---|---|---
r edid in!| Get the EDID status of the input| r edid in!| input EDID: 4K2K60_
444,
Stereo Audio 2.0
|
r edid in data!| Get the EDID data of the HDMI input| r edid in data!| EDID
data: 00 FF FF
FF FF FF FF 00
……
|
Command Code| Function Description| Example| Feedback|
Default Setting
---|---|---|---|---
RS-232 BYPASS Setting
| Set RS-232 port connects to| | RS-232|
s rs232 bypass
HDBT y!
| HDBT out1 Receiver RS-232
port, y=0~5( 0=all,
| s rs232 bypass HDBT| connects to HDBT OUT1| y=0
| 1~4= HDBT out 1~4 5=NC)| 1!| RS-232 not|
| | | connect|
| | | to HDBT OUT|
| | | RS-232|
r rs232 bypass!
| Get RS-232 port to connect to HDBT out receiver RS-232 port|
r rs232 bypass!
| connects to HDBT OUT1
RS-232 connects
to all HDBT OUT
| | | RS-232 not
| | | connect
| | | to HDBT OUT
| Set receiver control device| s device baud 57600
size 8
stop 1 parity none!
| receiver device|
s device baud w| COM port setting, w=2400,| COM port setting
size x stop y| 4800,9600,19200,38400,| baudrate: 57600
parity z!| 57600,115200, x=7,8| data size :8,
| y=1,2, z=none, even,odd| stop:1 parity:
| | none
s rs232 time x!
| set send RS232 command wait time x=200~5000ms| s rs232 time 200!| send RS-232 command wait time 200ms|
200ms
Application Example
The terms HDMI and HDMI High-Definition Multimedia Interface, and the HDMI Logo are trademarks or registered trademarks of HDMI Licensing LLC in the United States and other countries.
Read More About This Manual & Download PDF::
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>