KICKASS Fridge/Refrigerator User Manual
- June 6, 2024
- KICKASS
Table of Contents
Fridge/Refrigerator
FRIDGE / FREEZER
OPERATION MANUAL
Please read all instructions and the safety section carefully before using
your new KickAss® refrigerator.
TABLE OF CONTENTS
FEATURES
1
IMPORTANT SAFETY SYMBOLS
1
IMPORTANT SAFETY INSTRUCTIONS
2
CONTENTS IN THE BOX
3
SETUP
4
ELECTRICAL
4
BATTERY PROTECTION VOLTAGES
5
CABLE SPECIFICATIONS
5
CONTROL PANEL
6
OPERATION – GENERAL
7
MAIN POWER PANEL
8
ACCESSORY SOCKET PANEL
8
DRAINAGE BUNG
8
FRIDGE COVER
9
OPERATION – BLUETOOTH
10
TROUBLESHOOTING BLUETOOTH APP
11
CLEANING AND MAINTENANCE
12
TROUBLESHOOTING
12
ERROR CODES
13
WIRING DIAGRAM – SINGLE ZONE
14
WIRING DIAGRAM – DUAL ZONE
15
WARRANTY STATEMENT
16
Thank You For Purchasing A KickAss® Fridge / Freezer
Features: Digital electronic thermostat with LED temperature display Bluetooth
for remote control and monitoring of the fridge with your smartphone Reliable
refrigeration system using the Secop compressor Efficient electronic
technology, low energy consumption Multi-voltage system (DC 12-24 Volt) and
(AC 100-120/220-240 Volt) Anderson power connection and accessory socket
outlets Adjustable low voltage battery protection
Please ensure all safety and operational instructions are read carefully to
get the maximum benefit from your new fridge.
IMPORTANT SAFETY SYMBOLS
Warning! – Safety Directive Failure to observe this directive could lead to
serious injury.
Caution! – Safety Directive Failure to observe this directive could lead to
injury or damage to the appliance.
Note! – Important Information Failure to observe this note may lead to damage
to the appliance or impede performance.
1
IMPORTANT SAFETY INSTRUCTIONS
WARNING: Do not touch exposed cables.
WARNING: Do not use fridge if you suspect any connections could be wet.
WARNING: When using the fridge in the vehicle or boat, please make sure the
circuit being used is fused. If using a 240V AC power source ensure the supply
is fitted with a residual current device.
CAUTION: Any installation of DC power systems should be handled by a qualified
professional. Make sure the source voltage is correct. The technical data
label has the voltage data. Do not place any electrical devices inside the
refrigerator as moisture could harm these devices.
WARNING: When positioning the appliance, ensure the supply cord is not trapped
or damaged.
WARNING: Do not locate multiple portable socket-outlets or portable power
supplies at the rear of the appliance. This appliance is not intended for use
by persons (including children) with reduced physical, sensory or mental
capabilities, or lack of experience and knowledge, unless they have been given
supervision or instruction concerning use of the appliance by a person
responsible for their safety. Children should be supervised to ensure that
they do not play with the appliance.
WARNING: fill with potable water only. Do not store explosive substances such
as aerosol cans with a flammable propellant in this appliance.
This appliance is intended to be used in household and similar applications
such as staff kitchen areas in shops, offices and other working
environments; farm houses and by clients in hotels, motels and other
residential type environments; bed and breakfast type environments;
catering and similar non-retail applications.
The appliance contains fluorinated greenhouse gases. Chemical name of the gas:
R134a Fluorinated greenhouse gases are contained in hermetically sealed
equipment. An electrical switchgear has a tested leakage rate of less than 0.1
% per year as set out in the technical specification of the manufacturer.
CORRECT DISPOSAL OF THIS PRODUCT
This marking indicates that this product should not be disposed with other
household wastes throughout the EU. To prevent possible harm to the
environment or human health from uncontrolled waste disposal, recycle it
responsibly to promote the sustainable reuse of material resources. To return
your used device. Please use the return and collection systems or contact the
retailer where the product was purchased. They can take this product for
environmental safe recycling.
2
CONTENTS IN THE BOX
KickAss® Fridge / Freezer – Main Unit
240 Volt AC Power Cable
12 Volt DC Anderson Power Cable
Heavy Duty Protective Fridge Cover
12 Volt DC Anderson to Cigarette Plug Adapter
3
SETUP
GENERAL
Note! – Your refrigerator requires good ventilation, especially around the
vents of the refrigerator; allow a gap of at least 200mm around the vents.
Caution! -Humidity inside the appliance can form frost and impair cooling. Do
not allow frost to build up. Never clean the appliance using a hose and never
submerge the unit in any liquid.
Avoid placing your refrigerator near a heat source. This helps the
refrigerator to work more efficiently and keep the contents cool. Place the
refrigerator on a flat surface and away from any edges. When using the fridge
in a vehicle, please use a fastening device to secure it. Caution! – The
appliance can only be connected to one power source at a time. Note! – Water
resistant rating IPX4. Note! – Suitable for camping use.
ELECTRICAL Power: The electronic control module controls the compressor motor
and includes three stage battery protection. When the input voltage drops
below the minimum, the compressor will cut out; when the voltage rises to the
cut-in value, the compressor will restart automatically. Battery Protection:
The Secop Compressor requires approximately 10.6Volts (12Volt System). Note:
The early warning alarm will sound off every 4 seconds for 30 minutes before
the compressor shuts off. If an alternative power source is not found, the
early warning alarm will sound off every 8 seconds for 30 mins until the unit
has no more power.
4
BATTERY PROTECTION VOLTAGES
Voltage Setting
Low Level Medium Level
High Level
Turn Off Compressor (to protect battery)
12V Battery Protection
Early warning alarm system will notify before turning off compressor (to
protect battery)
10.3V
10.6V
11.1V
11.3V
11.6V
11.9V
Turn On Compressor
11.4V 12.2V 12.7V
Voltage Setting
Low Level Medium Level
High Level
24V Battery Protection
Turn Off Compressor (to protect battery)
Early warning alarm system will notify before turning off compressor (to protect battery)
21.5V
23.3V
23.6V
24.5V
24.8V
Turn On Compressor
23.0V 25.3V 26.2V
CABLE SPECIFICATION
The DC cables must have a suitable cross-section for their length, according
to this table:
Cable Area
12V Max Cable Length*
24V Max Cable Length*
Note! The length is from the battery to the refrigerator.
5
CONTROL PANEL
SINGLE ZONE
881848C
CCOOMMPRESSOR
HIGH MED LOW
DUAL ZONE
881848C
COMPRESSOR
HIGH MED LOW
-82828C8
6
OPERATION – GENERAL
TURN FRIDGE ON OR OFF
CHECK VOLTAGE OF THE FRIDGE
SET BATTERY PROTECTION LEVEL
CHECK FRIDGE BLUETOOTH ID
WHEN FRIDGE IS OFF, HOLD POWER BUTTON FOR 3 SECONDS TO TURN ON. WHEN FRIDGE IS ON, HOLD POWER BUTTON FOR 3 SECONDS TO TURN OFF.
8888
8.2878487
TAP THE BATTERY BUTTON AND THE LCD DISPLAY WILL SHOW THE CURRENT VOLTAGE OF THE FRIDGE.
HIGH MED LOW
BEEP
HIGH MED LOW
HIGH MED LOW
WAIT
HOLD THE BATTERY BUTTON FOR 3 SECONDS, YOU WILL HEAR A BEEP, THEN TAP THE
BATTERY BUTTON TO SCROLL TO THE OPTIONS (HIGH, MED & LOW). THEN WAIT TO SAVE
CHANGES.
HIGH SETTING WILL ALLOW THE FRIDGE TO DRAIN THE BATTERY ONLY IF THE BATTERY
LEVEL IS HIGH. MED SETTING WILL ALLOW THE FRIDGE TO DRAIN THE BATTERY ABOUT
HALFWAY LOW SETTING WILL ALLOW THE FRIDGE TO DRAIN THE BATTERY TO LOW TO KEEP
ITSELF RUNNING.
8888
80808C8S
PLEASE NOTE: YOU MUST ADD THE NUMBERS ’00’TO THE START OF THE BLUETOOTH ID. PLEASE NOTE: DUE TO THE DIGITAL DISPLAY, THE LETTERS b, B AND O CAN BE MISTAKEN FOR THE NUMBERS 8, 6 AND 0.
TAP THE COOLING SPEED BUTTON AND THE LCD DISPLAY WILL SHOW THE FRIDGE’S BLUETOOTH ID.
SET FRIDGE COOLING SPEED
BEEP
WAIT
HOLD THE COOLING SPEED BUTTON FOR 3 SECONDS, YOU WILL HEAR A BEEP, RELEASE THEN TAP THE COOLING SPEED BUTTON TO SCROLL TO THE OPTIONS (QUICK, NORM & ECO). WAIT TO SAVE CHANGES. QUICKLY COOL THE FRIDGE WITH MUCH MORE BATTERY DRAIN. NORMAL COOLING SPEED WITH NORMAL BATTERY DRAIN. SLOWEST COOLING SPEED WITH THE MOST ECONOMICAL BATTERY DRAIN.
8-82808C 8-81878C
LEFT BIN RIGHT BIN
8-82808C 8-81878C
OR
LEFT BIN
RIGHT BIN
8-82808C
LEFT BIN
8-81858C
RIGHT BIN
SETTING TEMPERATURE FOR A ZONE
8-82808C 8-81878C
OR
LEFT BIN
RIGHT BIN
8-82828C 8-81858C
LEFT BIN
RIGHT BIN
WAIT
TO CHANGE TEMPERATURE SETTINGS FOR EACH ZONE, START BY HOLDING THE SETTINGS BUTTON FOR 3 SECONDS THEN THE RIGHT BIN LCD NUMBERS WILL FLASH. TAP UP OR DOWN BUTTONS TO ADJUST TO THE DESIRED TEMPERATURE FOR THE RIGHT BIN. TAP THE SETTINGS BUTTON AGAIN AND THE LEFT BIN LCD NUMBERS WILL NOW FLASH. TAP UP OR DOWN BUTTONS TO ADJUST THE LEFT BIN TO THE DESIRED TEMPERATURE. AFTER YOU ARE SATISFIED, JUST WAIT TO SAVE THE CHANGES YOU MADE.
TURNING ON OR OFF THE LEFT BIN
8-82808C
LEFT BIN
8-81858C
RIGHT BIN
8-8-8-8-
LEFT BIN
8-81858C
RIGHT BIN
8-82808C
LEFT BIN
8-81858C
RIGHT BIN
PRESS BOTH THE SETTINGS BUTTON AND THE UP BUTTON FOR 3 SECONDS. THE LEFT BIN LCD DISPLAY WILL SHOW DASHES TO INDICATE THE LEFT BIN IS TURNED OFF. REPEAT THE SAME PROCESS TO TURN THE LEFT BIN BACK ON.
TURNING ON OR OFF THE RIGHT BIN
8-82808C
LEFT BIN
8-81858C
RIGHT BIN
8-82808C
LEFT BIN
8-8-8-8-
RIGHT BIN
8-82808C
LEFT BIN
8-81858C
RIGHT BIN
PRESS BOTH THE SETTINGS BUTTON AND THE DOWN BUTTON FOR 3 SECONDS. THE RIGHT BIN LCD DISPLAY WILL SHOW DASHES TO INDICATE THE RIGHT BIN IS TURNED OFF. REPEAT THE SAME PROCESS TO TURN THE RIGHT BIN BACK ON.
NOTE ON TURNING OFF BOTH BINS
8-82808C
LEFT BIN
8-8-8-8-
RIGHT BIN
8-8-8-8-
LEFT BIN
8-81858C
RIGHT BIN
8-82808C
LEFT BIN
8-8-8-8-
RIGHT BIN
YOU CAN ONLY TURN OFF ONE BIN AT A TIME. TRYING TO TURN OFF BOTH BINS WITH THIS METHOD WILL AUTOMATICALLY TURN ON THE OTHER BIN. IF YOU WANT TO TURN OFF BOTH BINS SIMPLY TURN OFF THE FRIDGE.
PRESS AND HOLD BUTTON
TAP BUTTON
BEEP HOLD AND WAIT FOR THE BEEP
WAIT AND DON’T PRESS ANYTHING
WAIT
MAIN POWER PANEL
OFF ON
OVERRIDE SWITCH
BACK TOP VIEW
FRONT
MAKE SURE YOU DON’T HAVE ANY OBSTRUCTIONS NEAR THE FRIDGE VENT HOLES TO AVOID OVER HEATING. ABOUT A MINIMUM OF 5 INCHES OF CLEARANCE IS NEEDED.
For emergency purposes (faulty operation or control panel not working properly) there’s an override switch users can use. To access the override switch you need to remove the cover, the override switch is not visible or accessible until the cover is removed. You can flick the override switch to bypass the control panel and force the fridge to cool up and freeze what you have in the fridge. This will however only freeze the zone of the fridge that is currently turned on before flicking the override switch. NOTE: If the override switch is turned on, the control panel will show the temperature and voltage but you will not be able to set them
ACCESSORY SOCKET PANEL
12V/24V ACCESSORIES/ CIGARETTE SOCKET 15A
DUAL USB SOCKET 2A
The front accessory panel comes with a cigarette socket and 2 usb sockets. This will only work if the DC 12/24V Anderson Connector on the side is attached to a power source. The output of these sockets are dependant on the power supply attached to the DC 12/24V Anderson Connector on the side. If it’s connected to a 12V source, the output is 12V, if its connected to a 24V source, the output will be 24V. WARNING * If it is connected to a 24V source, ensure that all 12V devices are disconnected that are not rated for 24V.
DRAINAGE BUNG
8
VELCRO VELCRO
HOW TO PUT THE FRIDGE COVER ON
We recommend having 2 people lift the fridge together when putting the fridge
cover on as the unit is heavy.
VELCRO
Important Note – Please remove the cover of the fridge once a month and wipe
any condensation or moisture build up off of the fridge and the cover. If
using the drainage bung please remember to remove the fridge from the cover
and wipe any excess liquid from the fridge once done.
9
OPERATION – BLUETOOTH
This fridge has been designed with the latest bluetooth technology to remote
control and monitor temperature from your smartphone. To get started please
download the KA FRIDGE app from the Google Play store or the Apple iTunes
Store.
Once the APP is installed please follow these easy instructions to be able to
control and monitor your fridge.
Turn on your phone’s bluetooth and location services.
Tap on the “Connect To Fridge” on the phone when the fridge appears in the
app.
myfridge
123456
Connect with the fridge by entering an alias for the fridge and then
enter the verification code. Method for acquiring verification code
is explained below.
0898868
COMPRESSOR
0898868
HIGH MED LOW
fig. 1
After powering on the Kickass Fridge, press the button on the right corner of
control panel (cooling speed button) and then the display will show four
characters as the Bluetooth ID (Verification Code) from control panel.
In the example on fig. 1, the bluetooth/verification code is 0986.
KickAss0986
FRIDGE NAME
myfridge 123456
ALIAS
000986
VERIFICATION CODE
CANCEL
CONTINUE
fig. 2
On the login screen (fig. 2) enter the verification code using the 4
characters you have obtained on the fridge control panel (fig. 1).
When adding the verification code, add leading “00” in front of the 4
characters you have. In our example we have obtained 0986 on the control
panel, adding 2 zeroes in front, our verification code is 000986.
10
Device Connected
Help
myfridge
CURRENT TEMP
24°C
LEFT BIN
10°C Tap to turn off the bin
FRIDGE CONNECTED
USER MANUAL
POWER
CURRENT TEMP
24°C
RIGHT BIN
10°C Tap to turn off the bin
TEMP DOWN
TEMP UP
TEMP DOWN
TEMP UP
BATTERY PROTECTION
24.80V
VOLTAGE
HIGH MED LOW
SWITCH BATTERY PROTECTION
COOLING SPEED
ADVANCED SETTINGS
TOGGLE COOLING SPEED
ADVANCED SETTINGS
POWER ON/OFF FRIDGE ALIAS FRIDGE ZONE TEMP
FRIDGE ZONE TEMP ADJUST
SWITCH BATTERY PROTECTION LEVEL
ADVANCE SETTINGS COOLING SPEED ADJUST
Y POWER ON/OFF – Turn off the fridge Y FRIDGE ALIAS – Bluetooth connection
name Y FRIDGE ZONE TEMP – Display current zone
temperature. Y FRIDGE ZONE TEMP ADJUST BUTTONS – Adjust a
zone’s current temperature with the TEMP UP and TEMP DOWN buttons. Y SWITCH
BATTERY PROTECTION LEVEL – Adjust the level of drain allowed for the fridge on
the connected battery. Y COOLING SPEED ADJUST – Adjust the compressor cooling
speed for the fridge. Y ADVANCE SETTINGS BUTTON – Switch to the graph screen
to check the fridge performance Y TEMPERATURE METRIC – Switch view of the
graph screen to either show as Fahrenheit or Celsius.
Fig. 1.1 – Single Zone App Screen
Fig. 1.2 – Dual Zone Graph Screen
Fig. 1.3 – Single Zone Graph Screen
Fig. 1.4 – Temperature Metric
TROUBLESHOOTING THE BLUETOOTH APP
Question : I can not see or connect the Bluetooth APP Make sure Bluetooth is
turned on, on your device. Make sure you are in range of the fridge (normally
around 10-20meters) Make sure you are using the correct verification code for
the Bluetooth APP Try turning the Bluetooth off and on.
If the above failed then follow the below steps: Uninstall the APP or close
all APPs in the background Turn both the fridge and the phone off for a couple
of minutes. Re-install the APP
If you are still having problems please do not hesitate to contact Kickass.
11
CLEANING AND MAINTENANCE
Clean the appliance inside and out with a damp cloth after every use. If it is
dirty, use sodium bicarbonate dissolved in lukewarm water to clean the unit.
Note! Never use abrasive products, detergents or soap. After washing, rinse
with clean water and dry carefully. Do not leave the refrigerator off with
food inside or lid closed. Caution! Never clean the appliance under running
water. Do not use abrasive cleaning agents or hard objects during cleaning as
these can damage the refrigerator.
TROUBLESHOOTING
The appliance is not turning on Hold ON button Check the power supply Check if
the plug and the socket have a good connection Check if the fuse requires
replacement
The food inside is frozen The setting temperature is too low ** Check the set
temperature and if above freezing, please contact us.
Bad performance in refrigeration The temperature setting is inappropriate The
lid is unlocked/or open The lid seal is broken Problems arising from poor
ventilation Too much food has been placed inside the refrigerator There is too
much warm product inside There is a heat source near the unit
The sound of water can be heard from inside the unit This is normal, due to
the flow of the refrigerant
Unusual noise when refrigerator is working Check if the surface the
refrigerator is on is level Loose componentry inside the refrigeration
compartment (see a service agent)
PLEASE NOTE : This fridge is fitted with an automatic 60 second re-start
delay. This will be activated if your fridge enters an error mode. This is to
protect the fridge if an error has occurred.
12
ERROR CODES
Error Code Error 1 Error 2 Error 3
Error 4 Error 5 Error 6/7
Error type can be read out on the control display
Battery protection cut-out Please check the source voltage to ensure it is
above the cut out.
Try lowering the voltage cut out setting to LOW The vehicle cabling may be
inadequate/unsuitable. Please refer
to cable specification table for correct cable thickness (Page3) Try on a
different power source
Fan issue Fan is drawing too many Amps(Over 1 Amp)
Contact Kickass
Compressor Start Issues Unplug for 10 minutes Try on a different power source
Possible electronic box or compressor fault
Contact Kickass
Compressor speed is too low Unplug for 10 minutes Reduce product load inside
unit Move unit to a lower ambient temperature Clean vents/ensure clear air-
flow over compressor
Ambient Temperature too high Clean Vents/ensure clear air flow
Thermostat failure Check if the NTC thermistor has a short circuit or has
no connection
13
WIRING DIAGRAM – SINGLE ZONE
AC 100-240V
50/60HZ
L
ADAPTER
N
-+ DC 12/24V
-+
12V
F+
F-
USB
D
C
P
T
TEMP. SENSOR
2
1 BK
BK
RD
BK
21 P3
1 2 P5
+-
D C P T 21
P1
P2
CONTROL AND OPERATION UNIT
P7
P4
21
21
RD BK DOOR SW LAMP
DOOR SW LAMP
COMPRESSOR UNIT
MOTOR FAN
14
WIRING DIAGRAM – DUAL ZONE
AC 100-240V
50/60HZ L
N
ADAPTER
-+ DC 12/24V
–
12V USB
TEMP. SENSOR
2
1 BK
TEMP. SENSOR
BK
2
1 BK
BK
F+ FD C P T
COMPRESSOR UNIT
21 P3
1 2 P5
21
+-
P6
P1
D C P T 21 P2
CONTROL AND OPERATION UNIT
P7
P4
21
21
2 P9 1
MOTOR FAN
ELECTROMAGNETIC VALVE
RD DOOR SW LAMP
BK
RD DOOR SW LAMP
BK
15
FRIDGE/FREEZER RANGE
WARRANTY STATEMENT TERMS AND CONDITIONS
KickAss® undertakes to the original purchaser that this product is sold free
of defect in materials and/or workmanship under normal use for a period of 5
YEARS. Subject to the following: –
Y The warranty period commences from the date of purchase by the original
purchaser from an authorised KickAss® dealer.
Y KickAss® will honour this warranty on presentation of proof of purchase of
the unit to KickAss® or its approved service agent. The service agent may be
requested to provide KickAss® with a photocopy of the proof of purchase to
obtain approval to proceed prior to warranty being honored.
Y Please submit a warranty form via warranty.australiandirect.com.au for
details and the name of an authorized service agent or refer to list provided.
It is the purchaser’s responsibility to freight the unit to and from the
service agent.
Y KickAss® will not be held responsible for any damage or loss suffered or
cost incurred whilst fridge is in transit.
Y Warranty repairs may only be carried out by an authorised service agent. Y
KickAss® will not reimburse repair claims carried out by unauthorized service
agents. Any unauthorized tampering with any part of the unit will
automatically void the warranty. Y Service agents may charge a fee for viewing
or testing the unit. This is not covered by KickAss® or this warranty and is
payable at the service point unless authorized by KickAss®. Y Any KickAss®
authorized service centre in Australia will be able to carry out the service
of your unit. If a repair needs to be undertaken and is covered in terms of
this warranty a Warranty Authorization Number must be obtained prior to
commencement of any work.
16
KickAss® will not accept a warranty claim if:
1. Modifications have been carried out to the unit without KickAss® written
authority. 2. Damage to or failure of the unit has been caused in KickAss®
opinion by incorrect, extreme or
unreasonable use. 3. Damage to or failure of the unit has been caused in
KickAss® opinion by misuse, neglect, accident,
impact or similar cause. Refer the preventative maintenance guidelines. Y
KickAss® has total discretion on the variation of the warranty terms. Y Our
goods come with guarantees that cannot be excluded under the Australian
Consumer Law. You are entitled to a replacement or refund for major failure
and for compensation for any other reasonably foreseeable loss or damage. You
are also entitled to have the goods repaired or replaced if the goods fail to
be of acceptable quality and the failure does not amount to a major failure. Y
The above warranty conditions are in addition to any other rights and/or
remedies as per the applicable law. Y Failure to follow the
guidelines/recommendations in this manual may void the warranty. Y This
warranty cannot be varied by others.
For warranty, please visit kickass.com.au/warranty
17
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>