crosswater LONDON PRO-F5932-C-WH Freestanding Bathtub Instruction Manual
- May 15, 2024
- CROSSWATER LONDON
Table of Contents
crosswater LONDON PRO-F5932-C-WH Freestanding Bathtub
Introduction
This bathtub has been fully inspected throughout the production process and
only leaves our factory after a 15-step QC process. Unpack and inspect the
bathtub before removing the fixture being replaced, if applicable.
Carefully remove the bathtub from the box, taking care the bathtub is carried
in the bag. Check that all parts have been supplied.
Before beginning installation of the bathtub please check for any damage that
may have occurred during transport.
Note: Damage claims cannot be made during or after installation.
Improper installation shall result in loss of warranty in case of damage
caused by impacts or rubbing against rough surfaces.
Prior to installing the bathtub prepare a connection of water inlet/ outlet.
Pay attention to leveling of floor where the bathtub will be located, ensuring
it can take the weight of the bathtub, water and bather(s). The customer may
choose the type and location of the faucets, installation instructions should
be supplied by the faucet manufacturer.
The installation procedure of the bathtub may differ from that described in
the installation instructions, depending on where you wish the bath tub to be
located.
Wet surface of the bathtub may create a risk of slipping which may increase by
using soap, shampoo, oils and similar products.
IMPORTANT: Please read these instructions carefully before beginning and
retain for future reference.
We do not accept responsibility for any problems that may occur through
incorrect installation.
RECOMMENDATIONS:
-Walls and floor should be fully tiled and finished before installation.
This ensures that the product is installed flat to the tile face and allows
the product to be easily removed in future, if required.
- Remove the protective packaging after installation of the bathtub.
- Only fill the bathtub with water up to 2/3 of its height.
- Use US-CW20-WH waste flow products with this bathtub
Installation notes
The installation must comply with all plumbing codes including local codes and
be installed by a licensed plumbing contractor.
Store the bathtub in a safe place until you begin installation to avoid any
damage.
Assemble the bathtub on a mat to protect against damage to the bath tub
surface.
Avoid getting cement, grit, sand or masonry products on to the surface.
Protect and cover the bathtub during the installation period to prevent damage
from occurring.
Never use brown tape or gaffer tape directly on to the surface. if the bath
has to be repacked remember to avoid taping directly on to the surface of the
bathtub.
IMPORTANT : Turn off the main water supply before connecting to any existing pipe work or doling any maintenance.
WARNING! Please check for any hidden pipes and cables, electric or otherwise, before drilling boles in a wall or floor.
Dimensions
Weight – 216lbs Weight with water – 770lbs
2/3 Height = 67 Gal./252L
Tools required
-
Tape measure
-
Safety glasses
-
Set square
-
Pencil
-
Spirit level
-
Silicone sealant
Installation – carriage
IMPORTANT:
This bathtub is heavy and installation requires 2 people.
Cross water London cannot accept responsibility for any injuries caused to
those attempting to install this bathtub without adequate and appropriate
tools or resources.
- Remove the bathtub from the packaging using the bag with handles.
- Use the bag with handles to lift and move the bathtub.
- Do not drag the bathtub over rough surfaces or sharp objects. Lift and place the bath tub into position.
- Do not drop the bathtub!
- Check that the wedges have been supplied.
Installation
-
This installation guide does not include details of waste connection, final decision about installation of waste connection should be made by a licensed plumber.
-
Install the waste according to the installation instructions supplied with the waste.
WARNING: DO NOT OVERTIGHTEN the waste as this may cause long term damage to the bath. We recommend to use a torque wrench to tighten the waste by using a torque force between 25Nm or 18.5 ft/lb and 50Nm or 36.8 ft/lb.
-
Under floor access is required for plumbing of bath tub waste.
-
Place the 4 wedges in position.
Maintenance
Clean the bath regularly with non-abrasive soap and warm water. Fully rinse
after cleaning.
While Clear stone is highly stain resistant, it is recommended that bath water
containing additives such as oils or salts is always drained and rinsed
immediately after use.
Please note that hair dyes and color cosmetics (eg. mascara, lipstick, face
powder) may leave a slight discoloration if not removed immediately.
If any strong chemicals come into contact with the bathtub, remove and rinse
immediately. Water temperature should not exceed 49˚C/120˚F.
For a fine scratch or a slight mark, use a 1500 grade sandpaper , Gently and
the area with water. for best results ,limit sanding to the smallest possible
area around the scratch. Re-polish the surface afterwards using a neutral
polishing compound or toothpaste. It may be possible to polish very scratches
ways without using abrasive papers: scrub gently with soft brush or plastic
pad (not metal scouring pad) and a mildly abrasive cream cleaner. Afterwards
scrub the whole area with plenty of clean water and re-polish as before.
If the scratch or mark is too deep and cannot be repaired using the above
method, it is possible to purchase a repair kit US-CRK. In order to remove the
scratches, follow the instructions included with the kit.
Warranty – This Crosswater London product is covered by a limited lifetime
warranty. For full details, terms and conditions please visit our website.
For further information contact: Crosswater London, 393 Fortune Blvd.,
Milford, MA 01757
Toll free number: 844-XWATER-1 (844-992-8371)
tel: 508-381-0433 fax: 508-381-6068
www.crosswaterlondon.com
email:
technical@crosswaterlondon.com
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>