KICKASS KASTSP200 Super Thin Solar Panel User Manual
- June 1, 2024
- KICKASS
Table of Contents
SUPER THIN
SOLAR PANEL
KASTSP200 Super Thin Solar Panel
Thank you for purchasing a KickAss Super Thin Solar Panel.
This range is the apex in portable, convenient and lightweight solar power to
suit any camping lifestyle.
SUPER THIN SOLAR PANEL DIMENSIONS
SUPER THIN SOLAR PANEL 200W
SPECIFICATIONS
| MODEL NO. | KASTSP200 |
|---|---|
| RATED MAXIMUM POWER | 200W |
| VOLTAGE AT PMAX (VMP) | 18.3V |
| CURRENT AT PMAX (IMP) | 10.98A |
| OPEN-CIRCUIT VOLTAGE (VOC) | 21.6V |
| SHORT-CIRCUIT CURRENT (ISC) | 13.1A |
PACKING DETAILS
| DIMENSIONS (mm) | 740 x 2065 x 20 |
|---|---|
| FOLDED DIMENSION (mm) | 740 x 515 x 85 |
| NET WEIGHT (kg) | 12.5 |
SUPER THIN SOLAR PANEL 300W
SPECIFICATIONS
| MODEL NO. | KASTSP300 |
|---|---|
| RATED MAXIMUM POWER | 300W |
| VOLTAGE AT PMAX (VMP) | 19.3V |
| CURRENT AT PMAX (IMP) | 15.55A |
| OPEN-CIRCUIT VOLTAGE (VOC) | 23.04V |
| SHORT-CIRCUIT CURRENT (ISC) | 16.7A |
PACKING DETAILS
| DIMENSIONS (mm) | 810 x 2680 x 20 |
|---|---|
| FOLDED DIMENSION (mm) | 810 x 670 x 85 |
| NET WEIGHT (kg) | 16.8 |
FOLDING SUPER THIN SOLAR PANEL
SUPER THIN SOLAR PANEL ACCESSORIES
SOLAR REGULATOR
NOTE: Please read all the way through instructions below at least once
before continuing & make sure the solar panel is connected to your battery and
lights are illuminated on the Controller.
NOTE: The regulator must be powered on first from the battery. Make sure
to connect the regulator with battery first, then connect to the solar panel.
The solar panel controller on the back of the panel can be set to charge 9
different battery types AGM, Gel, Flooded, 3/4/6/7 ternary Li-ion (3.7V) cells
in series, 4/8 LiFePo4 lithium cells in series.
Supported Battery Modes
- AGM Battery
- Gel Battery
- Flooded Battery
- 11.1V Li-ion cells in series
- 14.8V Li-ion cells in series
- 25.9V Li-ion cells in series
- 12.8V LiFePO4 cells in series
- 25.6V LiFePO4 cells in series
- 22.2V Li-ion cells in series
The controller is preset from factory for charging AGM (Type 1), so if you are using an AGM battery you do not need to do anything. To check or change what setting your regulator is on, please follow the instructions on the next page:
Step 1. Locate the controller which is affixed to the back of the solar panel.
Step 2. Locate the small black ‘Mode button’ on the right hand side of the
digital number display.
Step 3. Press and hold down the button for 3 seconds or until the digital
display beside the button begins to flash. While the display is flashing, press
the mode button to select Wait until display stops flashing. NOTE: Select , not
.
Step 4. When is selected, press the button for 3 seconds until the display starts flashing. Release the button, then press and hold it until 2 LEDs and the display start flashing. Continue pressing the button until you select the desired battery mode configuration.
- AGM Battery
- Gel Battery
- Flooded Battery
- 11.1V Li-ion cells in series
- 14.8V Li-ion cells in series
- 25.9V Li-ion cells in series
- 12.8V LiFePO4 cells in series
- 25.6V LiFePO4 cells in series
- 22.2V Li-ion cells in series
Step 5. After suitable battery type is selected, press and hold the button
until the LEDs are not flashing.
If your solar panel is connected to your battery and is charging normally,
indicators should show:
Battery Indicator – Solid On
Solar Indicator – Slow Flashing
KICKASSPRODUCTS.COM.AU
Documents / Resources
|
KICKASS KASTSP200 Super Thin Solar
Panel
[pdf] User Manual
KASTSP200 Super Thin Solar Panel, KASTSP200, Super Thin Solar Panel, Thin
Solar Panel, Solar Panel, Panel
---|---
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>