Shen Zhen Goldbulous Electronics PJ-32C Home Theater Projector Instruction Manual

PJ-32C Home Theater Projector

Home Theater Projector with BT INSTRUCTION MANUAL
MODEL NO. : PJ-32C
PLEASE READ BEFORE OPERATING THIS EQUIPMENT

Important Safety Instructions
1. Read these Instructions. 2. Keep these Instructions. 3. Heed all Warnings. 4. Follow all instructions. 5. Do not use this apparatus near water. 6. Clean only with a dry cloth. 7. Do not block any ventilation openings. Install in accordance with the manufacturer’s
instructions. 8. Do not install near any heat sources such as radiators, heat registers, stoves, or other
apparatus (including amplifier) that product heat. 9. Protect the power cord from being walked on or pinched particularly at plugs, convenience
receptacles, and the point where they exit from the apparatus. 10. Only use attachments/accessories specified by the manufacturer. 11. Unplug this apparatus during lightning storms or when unused for long periods of time. 12. Refer all servicing to qualified service personnel. Servicing is required when the apparatus
has been damaged in any way, such as power-supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped. 13. Use only with a cart, stand, tripod, bracket, or table specified by the manufacturer or sold with the apparatus. When a cart is used, use caution when moving the cart/ apparatus combination to avoid injury from tip-over.
1

Additional Warnings and Precautions
1. Do not look directly into the projector light. 2. Don’t touch the project lens 3. Mains adapter is used as disconnect device and it should remain readily operable
during intended use. In order to disconnect the apparatus from the mains completely, the mains plug should be disconnected from the mains socket outlet completely. 4. CAUTION: Use of controls or adjustments or performance of procedures other than those specified may result in hazardous radiation exposure. 5. WARNING: Changes or modified to this unit not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. 6. WARNING: Use of this unit near fluorescent lighting may cause interference regarding use of the remote. If the unit is displaying erratic behavior move away from any fluorescent lighting, as it may be the cause. 7. WARNING: Shock hazard – Do Not Open. 8. Caution and marking information is located at the rear or bottom of the apparatus. 9. WARNING: To reduce the risk of fire or electric shock, do not expose this apparatus to rain, moisture, dripping, or splashing. 10. Objects filled with liquids, such as vases, shall not be placed on the apparatus.
2

FCC Warning
This device complies with Part 15 of the FCC rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
· Reorient or relocate the receiving antenna. · Increase the separation between the equipment and receiver. · Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected. · Consult the dealer or an experienced radio/TV technician for help. Warning: Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
The equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. The equipment should be installed and operated with minimum distance 20cm between the radiator & your body.
In The Box
Main Unit Lens Cover Remote AC Power cord User Manual
3

Table of Contents
Important Safety Instructions – – – – – – – – – – – – – – – – – – – – – – – – – – – P1 Additional Warnings and Precautions – – – – – – – – – – – – – – – – – – – – – P2 FCC Warning – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – P3 In The Box – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – P3 Table of Contents – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – P4 Remove & Close the Lens Cover – – – – – – – – – – – – – – – – – – – – – – – – P5 Placing of Your Projector – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – P5 To Reduce Image Distortion – – – – – – – – – – – – – – – – – – – – – – – – – – – – P6 Distance Between The Projector And Screen – – – – – – – – – – – – – – – – P6 Installing your Projector in the Ceiling – – – – – – – – – – – – – – – – – – – – P6 Adjust The Vertical Location – – – – – – – – – – – – – – – – – – – – – – – – – – – – P7 Adjust The Focus And Keystone – – – – – – – – – – – – – – – – – – – – – – – P7 Controls of Remote – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – P8 Install / Remove Batteries of Remote – – – – – – – – – – – – – – – – – – – – – P8 Controls of Projector – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – P9 Install Power Adapter – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – P10 Main Button Operation – – – – – – – – – – – – – – — – – – – – – – – – – – – – – – – P10 Connect HDMI show the Image On Projector Screen – – – – – – – – – P11 Connect AV Show The Image On Projector Screen – – – – – – – – – – – P11 Connect VGA Show The Image On Projector Screen – – – – – – – – – – P12 Connect Audio Output (Aux Out / Line Out / Earphones) – – – – – – – P13 Install USB Device And Micro SD Card “TF” – – – – – – – – – – – – – – – – P13 Using TF Card and USB Playback DMP (Media Player) — – – – – – – – P14 Using Bluetooth Playback – – – – – – – – – – – – – – – – – – – – – – – – P15 Multi-screen interactive connection for phone and projector – – – – P16 Using Projector Menu 1 – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – P17 Using Projector Menu 2 – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – P18 Using Projector Menu 3 – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – P18 Specifications – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – P19
4

Remove & Close The Lens Cover

Remove the lens cover before using

Close the lens cover when unit is not using

Placing of Your Projector
Your projector can be installed in four different configurations (see picture below):
Front Table: Select this location with the projector placed near the floor in front of the screen. This is the most common way to position the projector for quick setup and portability.
Rear Table: Select this location with the projector placed near the floor behind the screen. NOTE: That a special rear projection screen is required.
Front Ceiling: Select this location with the projector suspended upside-down from the ceiling in front of the screen. NOTE: A projector mount is required to install the projector in a ceiling.
Rear Ceiling: Select this location with the projector suspended upside-down from the ceiling behind the screen. NOTE:
5

A projector mount is required to install the projector in a ceiling. A special rear projection screen is required.

To reduce Image Distortion
Move the projector as close to the center of the screen as possible.
The light beam from the projector should be perpendicular to the screen for a rectangular or square image.

Distance Between The Projector And Screen

Measure the distance between the projector and where you want to position the screen. This is the projection distance.

Distance
1.16m 1.35m 1.51m 1.79m 2.15m 2.81m 3.43m 4.44m

Screen Size
37inch 45 inch 50 inch 60 inch 72 inch 100 inch 120 inch 150 inch

Installing your Projector in the Ceiling
When installing the projector in the ceiling, please purchase a projector mount recommended by an installation professional and follow the instructions that come with the mount. Before installing the projector in the ceiling, please check to make sure the ceiling structure can support the weight of the projector and the mount. If in doubt, please ask the advice from an installation professorial.
NOTE: Projector mount and screw(s) not included

6

Adjust The Vertical Location
Follow below picture to adjust the vertical location.
Adjust The Focus And Keystone
Follow below picture to adjust the focus and trapezoidal screen. Adjust the focus by turning the knob while observing the image pixels near the center of the screen. Optimal focus is obtained when the pixels are clearly visible. Depending on the projected screen size, the focus near the screen edges may be less sharp than the screen center. Keystone image is created when the projector lens is projected from above or below the center of the screen. Keystone correction restores the distorted image to a rectangular or square shape.
7

Controls of Remote
Install / Remove Batteries of Remote
Remove the battery compartment cover on the back of your remote by carefully sliding to open. The battery cover can then be lifted away. Fit the correct batteries (not included), referring to the polarity markings. Finally, replace the cover.
NOTES: Batteries shall not be exposed to excessive
heat such as placing under the sunlight or near a fire. Please make sure the batteries are installed with their correct polarities. Do not mix old and new batteries. Use only the same type of batteries. Do not dispose of the batteries in fire, battery may explode or leak. Do not recharge a non- rechargeable battery.
8

Controls of Projector

1 LENS 2 ANGEL ADJ. Knob 3 AC IN Socket 4 FOCUS ADJ. Knob 5 TRAPEZOIDAL ADJ. Knob 6 POWER Indicator 7 POWER Button 8 RETURN Button 9 SOURCE Button 10 MENU Button

11

Buttons

12

Buttons

13

Button

14 Audio out Jack

15 AV IN Jack

16 TF Card Slot

17 HDMI 1 & 2 Ports

18 USB Port

19 VGA IN Port

20 IR Sensor

9

Install Power Adapter
Follow below picture to connect power cable Connect small end of cable FIRST. Plug the AC plug to power outlet.
WARNING:
Before connecting to the power supply, ensure that the supply corresponds to the information on the rating label at the back of the apparatus.
Main Button Operation
– Press the button to switch on unit, press again to turn off. / SOURCE – Press the button to select input source. / MENU – Press the button to enter projector menu.
– Press the buttons to navigate and select screen item of menu. / EXIT – Press the button to return to previous status or exit the menu.
– Press the buttons to fast search forward and rewind on USB / TF. – Press the buttons to search next or previous file on USB / TF. VOL+ / VOL – Press the buttons to select the sound level. – Press the button to play/pause the playback of file on USB / TF card. FLIP ­ Press the button to rotate / mirror projector screen ZOOM – Press the button to select image scale.
10

– Press to mute the audio. Press again to resume.
Connect HDMI Show The Image On Projector Screen
Refer to the following picture to connect a set top box, a BD/DVD player or a streaming player to the HDMI input. 1. Turn off the unit before connect HDMI cable. 2. After connection, press the button to turn on unit and power indicator will light
GREEN 3. Press the / SOURCE button to select HDMI 1 or HDMI 2 and the video from the
connected device will be shown on projector screen. 4. Press the button to turn off unit power.

Important Note: If there is no sound from the internal speakers when playing media contents from a set top box, BD/DVD or streaming players connecting to the HDMI input, please check the set top box or the player’s digital audio settings and make sure it is set to “PCM Stereo” mode.

Connect AV Show The Image On Projector Screen

Follow below picture to connect AV cable and device. 1. Turn off the unit before connect AV cable.

2. Use AV cable to connect follow below figure

3. After connect, press the button to turn on unit and power indicator will light GREEN

4. Press the / SOURCE button to select AV mode and the video of AV device will

show on projector screen

5. Press

the

button

to

turn off

unit

power

11

Connect VGA Show The Image On Projector Screen
Follow below picture to connect VGA cable and device. 1. Turn off the unit before connect VGA cable.
2. Press the button to turn off power of your projector before connection. 3. After connect, press the button to turn on unit and power indicator will light
GREEN 4. Press the / SOURCE button to select VGA mode and the video of VGA device
will show on projector screen 5. Press the button to turn off unit power.

Please refer to the following table to adjust the output signal from computer

Type Resolution

Frequency

Field Frequency

31.5

60

VGA

640×480

34.7 37.9

70 72

37.5

75

PC

31.4

50

35.1

56

SVGA

800×600

37.9

60

46.6

70

48.1

72

12

46.9

75

40.3

50

XGA

1024×768

48.4

60

56.5

70

NOTE: In order to get the sound from the unit, please connect AV IN cable when you connect VGA input.

Connect Audio Output ( Aux Out / Line Out / Earphones)
Follow below picture to connect audio cable and device.
1. Press the button to turn off power of your projector before connection. 2. Use audio cable to connect follow below figure. 3. After connect and turn on both units. Your projector sound from external device now. 4. After using , turn off both unit

Important Note: If there is no sound from the stereo audio output when playing media contents from a set top box, BD/DVD or streaming players connecting to the HDMI input, please check the set top box or the player’s digital audio settings and make sure it is set to “PCM Stereo” mode.

Install USB Device And Micro SD Card “TF”

Follow below picture to

install USB and TF card

Turn off the unit before

install USB / TF card.

13

Using TF Card And USB Playback DMP (Media Player)

Install USB / TF device: 1. Turn off the unit before install USB / TF card. 2. Install the USB device into USB port.
3. After connect, press the button to turn on unit and the power indicator light GREEN.

4. Press the mode.

/ SOURCE button to enter and use

buttons to search the DMP

5. After selection, use

buttons to search the PHOTO / MUSIC / MOVIE icon and

press the button to enter. If necessary, use the

button to select TF card or

USB and press the button to enter.

6. Use

buttons to search the correct file and press the button to preview

playback file and press the / EXIT button or button of remote to start playback.

7. Press

button to fast search forward and rewind.

8. Press

button to search next or previous file.

9. During playback, press the button to pause and press again to resume.

NOTE: Remove USB / TF device, press the button to turn off power FIRST.

Sub-Menu on Photo screen

1. When photo playback, press

Figure 1.

the button and more

function screen show on lower

(figure 1).

2. Use the

button to select

icon and press the button to play special function.

Sub-Menu on Music screen

1. When music playback, press

Figure 2.

the button and more

function screen show on lower

(figure 2).

2. Use the

button to select

icon and press the button to play special function.

Sub-Menu on Movie screen

1. When movie playback, press

Figure 3.

the button and more

14

function screen show on lower

(figure 3).

2. Use the

button to select

icon and press the button to play special function.

Using Bluetooth Playback
Pairing is the term used when two Bluetooth devices are connected wirelessly for the first time. This allows the devices to see each other and sets up a one to one communication channel between both devices.

Bluetooth Connection

1. Press the button to turn on unit and the power indicator light GREEN.

2. Press / MENU button to enter projector menu, press

buttons to select

SOUND menu

3. Use the

button to select Bluetooth column.

4. Press the button to turn “ON” 5. Turn on your External Bluetooth Speaker

Sound Mode Standard Balance 0 Bluetooth Off

and select to Bluetooth pairing mode.

6. A few seconds, you hearing “melody” sound that your unit and external Bluetooth

speaker connected.

7. After connection completed, the unit sound to External Bluetooth speaker.

Disconnect the Bluetooth

1. Press the / MENU button to enter the projector menu, press

select SOUND menu

2. Use the

button to select Bluetooth column

3. Press the button to turn “Off” that the Bluetooth disconnect.

buttons to

15

Multi-screen interactive connection for phone and projector
First, ensure the projector and the mobile is connected to the same wireless network Follow below steps to set up.

Support Screen Mirroring Settings (IOS mobile)

1. Press the / SOURCE button to enter and use

buttons to select the Screen

Mirroring mode.

2. Click the Wi-Fi menu to search and select “RKcast-XXXXXX” (XXXXXX is numbers

and letters. It show on the “Screen Mirroring” page) on the mobile device and enter

Pin “12345678” to connect

3. After connect, click the browser and input IP “192.168.49.1” address on the mobile.

4. Click to select Wi-Fi AP, choose the available local Wi-Fi router and input password to

connect.

5. After connect, the router’s name will be on the projector screen.

6. Click Screen Mirroring function on the mobile to achieve Screen Mirroring.

Support Airplay Settings (IOS mobile)

1. Press the / SOURCE button to enter and use

buttons to select the Screen

Mirroring mode.

2. Click the Wi-Fi menu to search and select “RKcast-XXXXXX” (XXXXXX is numbers

and letters. It show on the “Screen Mirroring” page) on the mobile device and enter

Pin “12345678” to connect

3. After connect, click the browser and input IP “192.168.49.1” address on the mobile.

4. Click to select Wi-Fi AP, choose the available local Wi-Fi router and input password to

connect.

5. After connect, the router’s name will be on the projector screen.

6. Click Mirror Icon of mobile player, select Airplay Bluetooth devices, will pop out select

device icon window, click “RKcast ­ XXXXXX” to achieve Screen Mirroring.

7. The mobile device will mirror and browse online contents to projector. You can enjoy

online video/music/pictures, etc. (This feature is only supported by iOS 7 or above

devices).
Note: When the router is successfully connected, the projector will automatically connect to the router next time. The mobile device can connect the projector or the router to mirror the network content.

Android Mirroring Settings (Miracast mode)

1. Press the / SOURCE button to enter and use

buttons to select the Screen

Mirroring mode.

2. Click the Wi-Fi menu to search and select available local Wi-Fi router and input

password to connect on the mobile.

3. Click Miracast function (different mobile models with different names) on the mobile

16

settings 4. Click to select “RKcast-XXXXXX” (XXXXXX is numbers and letters. It show on the
“Screen Mirroring” page) on the mobile settings. The mobile device contents will mirror on the projector screen

Android Mirroring Settings (DLNA mode)

1. Press the / SOURCE button to enter and use

buttons to select the Air Play

mode.

2. Click the Wi-Fi menu to search and select “RKcast-19A1EF” on the mobile device and

enter Pin “12345678” to connect

3. After connect, click the browser and input “192.168.49.1” IP address on the mobile.

4. Click to select Wi-Fi AP, choose the available local Wi-Fi router and input password to

connect.

5. After connect, the router’s name will be on the projector screen.

6. Click Screen Sharing or Wireless Display (different mobile models with different

names) on the mobile

7. The mobile device will mirror and browse online contents to projector. You can enjoy

online video/music/pictures, etc. (This feature is only supported by Android system 4.2

or above devices).

Note: When the router is successfully connected, the projector will automatically connect

to the router next time. The mobile device can connect the projector or the router to

mirror the network content.

17

Using Projector Menu 1
Press / MENU button to enter projector menu, press PICTURE menu.

buttons to select

This Picture menu showed on right upper of view screen.

Picture Mode Customer define Contrast Brightness Color Sharpness

Use

to select different picture effect to Medium / Soft

/ User / Vidid. Use

or

to select Contrast /

Brightness / Color / Sharpness digit If chose User item.

Follow below figure.

Use

to select different color temperature to Cool /

Medium / Warm / User. Use

or

to select Red /

Green / Blue digit If chose User item. Follow below figure.

Use

buttons to select screen ratio AUTO / 4:3 / 16:9.

Follow below figure.

Use

buttons to select Off / Low / Middle / High /

Default.

Use

buttons to select Auto Adjust / Horizon Pos. /

Vertical Pos. / Size / Phase. Use

or

to select

Horizon Pos. / Vertical Pos. / Size / Phase digit. Follow

below figure.

Use

buttons to select different zoom scale digit 75%

– 100%

Parameter 0-100 0-100 0-100 0-100

Color temper… (temperature)

Customer define Parameter

red

0-100

blue

0-100

green

0-100

18

Aspect Ratio AV mode
HDMI mode
VGA mode DMP (USB/TF Card) mode Air Play mode

Auto, 4:3, 16:9, Zoom1 ,Zoom2, Panorama Auto, 4:3, 16:9, Zoom1, Zoom2, Just Scan, Panorama, Point To Point Auto, 4:3, 16:9, Point To Point Auto, 4:3, 16:9
Auto, 4:3, 16:9, Zoom1, Zoom2, Just Scan, Panorama, Point To Point

PC Setting (Active in VGA mode)

Customer define

Parameter

(Press

Horizon Pos.

0-100

Vertical Pos.

0-100

Size

0-100

Phase

0-100

to set)

Noted: PC setting menu is activated in VGA mode only.

Using Projector Menu 2
Press / MENU button to enter projector menu, press menu.

buttons to select SOUND

This sound menu showed on right upper of view screen.

Use

to select different sound effect Standard / Music /

Movie / Sports / User. Use

or

to select Treble

and Bass digit if chose User item. Follow below figure to set

digit.

Use

to select Balance level to -50 to +50

Sound Mode – User Treble Bass

Press

buttons to select Off / On.
Parameter 0-100 0-100

Using Projector Menu 3
Press / MENU button to enter projector menu, press buttons to select OPTION menu.
This OPTION menu showed on right upper of view screen.

Use

button to select different language.

Use

buttons to select Y or N. If choose “Y” that your

unit will go to factory default setting.

Press

buttons repeatedly to select different OSD
19

Duration time Off / 5S / 10S / 15S / 20S / 25S / 30S.
Press buttons repeatedly to select Front / Rear Ceiling / Front Ceiling / Rear For service center use only.

Specifications

Bluetooth Version

4.2

Light Source Type

LED

HDMI Input Supported Video Resolution.

1080p , 1080i , 720p, 576i , 480p, and 480i

Power Consumption

67W

Included Adapter

Input AC100-240V, 50/60Hz

Projection Size Input Port

37-150 inch AV/ VGA / HDMI

USB Port

Support USB device up to 32GB

Support format Mpeg1, Mpeg2, Mpeg4, mp3, Jpeg

TF Card

Support SD card up to 32GB

Net Weight Product Dimensions

Support format Mpeg1, Mpeg2, Mpeg4, mp3 , Jpeg 1.4 KG 230 x 200 x 94 mm

Specifications are typical, individual units might vary. They are subject to continuous improvement without notice and without incurring any obligation.

FCC Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the
20

user is encouraged to try to correct the interference by one or more of the following measures: — Reorient or relocate the receiving antenna. — Increase the separation between the equipment and receiver. — Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. — Consult the dealer or an experienced radio/TV technician for help.
21

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>