xantrex 808-0817 Freedom X Remote Panel User Guide

xantrex 808-0817 Freedom X Remote Panel

DANGER
HAZARD OF FIRE, ELECTRIC SHOCK, EXPLOSION, OR ARC FLASH
This Freedom X Remote Panel User Guide is in addition to, and incorporates by reference, the relevant product manuals for each product in the Freedom X series. Before reviewing this guide you must read the relevant product manuals. Unless specified, information on safety, specifications, installation, and operation is as shown in the primary documentation received with the product. Ensure you are familiar with that information before proceeding.
Failure to follow these instructions will result in death or serious injury.

Exclusion for Documentation
UNLESS SPECIFICALLY AGREED TO IN WRITING, SELLER (A) MAKES NO WARRANTY AS TO THE ACCURACY, SUFFICIENCY OR SUITABILITY OF ANY TECHNICAL OR OTHER INFORMATION PROVIDED IN ITS MANUALS OR OTHER DOCUMENTATION; (B) ASSUMES NO RESPONSIBILITY OR LIABILITY FOR LOSSES, DAMAGES, COSTS OR EXPENSES, WHETHER SPECIAL, DIRECT, INDIRECT, CONSEQUENTIAL OR INCIDENTAL, WHICH MIGHT ARISE OUT OF THE USE OF SUCH INFORMATION. THE USE OF ANY SUCH INFORMATION WILL BE ENTIRELY AT THE USER’S RISK; AND (C) REMINDS YOU THAT IF THIS MANUAL IS IN ANY LANGUAGE OTHER THAN ENGLISH, ALTHOUGH STEPS HAVE BEEN TAKEN TO MAINTAIN THE ACCURACY OF THE TRANSLATION, THE ACCURACY CANNOT BE GUARANTEED. APPROVED CONTENT IS CONTAINED WITH THE ENGLISH LANGUAGE VERSION WHICH IS POSTED AT HTTP://WWW.XANTREX.COM

Introduction

Thank you for purchasing the Freedom X Remote Panel. This user guide will help you install and use the remote panel to operate and configure the Freedom X and XC series remotely.

What’s In The Box

Check that you have the following items in the box before proceeding.

• the Freedom X remote panel unit
• user guide and mounting template
• 25-ft. 6-conductor cable kit (808-0817-02 unit only)

What’s Required

If you received the 808-0817 unit, you need to acquire one of the following 6-conductor cable kit from Xantrex.
Go to http://www.xantrex.com/power-products-support to order.

• 25-ft. 6-conductor cable kit (PN: 31-6257-00)
• 50-ft. 6-conductor cable kit (PN: 31-6262-00)

Installation

1. Prepare the remote panel unit and the 6-conductor com cable kit.
2. Choose a location for the remote panel unit within reach of the com cable and the inverter unit.
3. Use the mounting template (in section A) to make the installation of the remote panel easier.
4. Mount the remote panel unit.
5. If you have a Freedom 458 unit, you may use it with the Freedom X Remote Panel. Installation instructions are available in section B.

Features

Function Buttons

NOTE: Briefly pressing any function button activates backlight illumination. After 60 seconds of inactivity, backlight illumination turns off.

Status LED Indicators

LCD Screen

Viewing Information During Battery Mode

Press scroll [ ] to move to the next screen. Press [ESC ] to return to the home screen 1 .

Viewing Information During Grid Mode

Press scroll [ ] to move to the next screen. Press [ESC ] to return to the home screen 1

Adjusting Feature Settings

1. Press and hold the [OK ] button for three seconds to enter the feature settings mode.

2. Press the scroll [ ] button to move through the different feature settings.
   NOTE: See the Freedom X / XC Owner’s Guide for information on the individual settings.

3. Press the [OK ] button to select a setting number and change its value.

4. Press the scroll [ ] button to change the value until you reach the desired value.

5. Press the [OK ] button to confirm the change.

6. Repeat previous steps to set other feature settings.

7. Press [ESC ] to exit the feature settings mode.

NOTE: It may take a minute for the settings to take effect on the inverter unit.

Contact Information
http://www.xantrex.com
Please contact your Xantrex Sales Representative or visit the Xantrex website at: http://www.xantrex.com/power-products-support/

Creating a Bluetooth Link with the Freedom X Remote Panel App

The Freedom X Remote Panel app (FXC Control) allows you to conveniently monitor and configure a Freedom X inverter (or a Freedom XC inverter/charger)a with a compatible smart deviceb using a Bluetooth connection.

1. Download and install the FXC Control app into a compatible Android or iOS smart device.
2. Turn on the Bluetooth enabled Freedom X Remote Panel by using the ON/OFF button on either its own front panel or the connected inverter’s front panel.
3. Launch the FXC Control app on your smart device.
4. Turn on the smart device’s Bluetooth through the Bluetooth toggle on the app. The app should now indicate that it is searching for devices.
5. On the Freedom X Remote Panel, press and hold the ESC button to enable Bluetooth pairing on the remote. Remote pairing can be observed by the two flashing horizontal lines underneath the left and right numbers.
6. When the app has detected the Bluetooth signal, it will display the connected inverter’s serial number in the app. Click on the serial number to complete the pairing process.
7. To stop the Bluetooth connection, disable the smart device’s Bluetooth connectivity.

Installing the Remote Panel Unit on the Wall

1. Place the template on the wall.
2. Mark the corners (or trace the dotted lines) of the recess outline on the wall.
3. Mark the two mounting holes for the two screws on the wall.
4. Remove the template from the wall.
5. Cut along the recess outline on the wall to make a hole for the remote panel’s body.
6. Pre-drill the mounting holes appropriate to the mounting screws (not provided) that will be used.
7. Connect the 6-conductor com cable to the RJ12 ports on the inverter and remote panel.
8. Mount the remote panel unit on the wall.

Mounting Template

Installing the Freedom X Remote Panel with a Wall Mount Adaptor

The Freedom X Remote Panel Wall Mount Adaptor (PN: 808-0819) allows the installation of the Freedom X Remote Panel onto an adaptor bezel which then fits over the existing wall panel opening of a Freedom 458 Basic Remote Panel.

1. Unmount the Freedom 458 Basic Remote Panel from the wall by removing the four screws securing it to the wall. Set aside the four screws.
2. Detach the six-conductor telephone cable from the Freedom 458 Basic Remote Panel.
3. Install the Freedom X Remote Panel Wall Adaptor to the wall at the outer corners with the four screws in step 1. Alternatively, use optional counter-sink screws, if needed.
4. Take the Freedom X Remote Panel and attach the six-conductor telephone cable from the wall opening.
5. Mount the Freedom X Remote Panel to the Freedom X Remote Panel Wall Adaptor securing it with the two supplied mounting screws.
6. Complete the inverter installation and start up procedure in the Freedom X/XC Owner’s Guide.

Copyright © 2018 Xantrex LLC. All Rights Reserved.
All trademarks are owned by Xantrex LLC or its affiliated companies. Other trademarks are owned by their respective companies.

References

• Xantrex | Power Inverter, Inverter Charger, Battery Charger Manufacturer
• Xantrex | Support

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>