Panasonic F-MQ409 Oscillation Auto Fan User Manual

Panasonic F-MQ409 Oscillation Auto Fan

SPECIFICATION

• VOLTAN/VOLTAGE/ 240 (V)
• IFREKUENSI/FREQ./ 50
• ROTATION (RPM)
• AIR VELOCITY (m/min)
• AIR DELIVERY (m3/min) 85
• NUMBER OF SPEEDS 5
• LOW: 694
• HIGH: 1295
• Before operating this set, please read these instructions completely.
• Use only with rated voltage.
• If the supply cord is damaged, it must be replaced by the manufacturer, its service agent, or similarly qualified persons in order to avoid a hazard.
• Ensure that the fan is switched off from the supply main before cleaning or maintenance.
• This appliance is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities, or lack of experience and knowledge unless they have been given supervision or instruction concerning the use of the appliance by a person responsible for their safety. Children should be supervised to ensure that they do not play with the appliance.
• To avoid the possibility of causing injury to users or damage properties, please follow all the explanations written within. The manufacturer is not responsible for accidents and injuries caused by defective or deficient installation.
• Thank you for purchasing this product.

SAFETY PRECAUTIONS

• Be sure to read and follow these safety directions Be sure to observe the following safety precautions carefully in order to avoid possible injury to yourself or others and damage to your belongings.
• The following symbols indicate the degree of possible danger if the relevant precautions are ignored.

WARNING: This indication shows the possibility of causing death or seriuos injury.

CAUTION: This indication shows the possibility of causing injury or damage to properties.

• Precautions are classified using the following symbols.
• This symbol denotes a PROHIBITED action.
• This symbol denotes actions that are COMPULSORY.

WARNING

• Never try to take apart, repair or modify this product.
• Do not take apart It may cause fire or electric shock.
• Contact the dealer for repairing this product.
• Do not connect line cord into outlet until fan has been completely assembled.
• Do not connect this unit to power supply other than destinated country rated voltage.
• Do not damage the power cord or main plug.

Prohibited

• Causing injury, electric shock or even fire due to short circuit
• If the supply cord is damaged, it must be replaced by the manufacturer or its service agent or a similarly qualified person in order to avoid a hazard.
• The safety wire must be always connected.
• Otherwise, it may cause fire and injury.
• Do not contact with water.

Avoid water

Causing fire or electric shock.

WARNING

• Disconnect the power supply before cleaning.
• Follow strictly all the instructions given in this manual for installation.
• Otherwise, it may cause an electric shock.
• Installation errors can cause fire, electric shock, set to fall, and injuries.
• May cause electric shock.
• Installation and wiring must be done by competent personnel.

CAUTION

• do not use under the following situations;
• Near to gaseous fuel cooker
• High temperature
• Place expose to rain or water pour
• Installation must strictly follow to wiring diagram provided
• Can cause electric shock, current leakage and fire if miswiring
• Ensure area of mounting fixture has sufficient strength.
• May cause bad effect in quality and dangerous condition.
• Don’t place the fan on unstable surface or near obstacles
• Make sure all screws and connection are tightly screwed and secured
• Risk on injury by falling fan.
• Please install the safety screw before fixing the guard.
• Avoid continuously exposure of direct wind from the fan.
• It may cause discomfort
• Can cause injury and product to fall.
• Do not fix at area exposed to strong vibration and knocking.
• Do not put your fingers into the guard or any moving part of the fan.
• Causing injury.
• The fan is recommended to be installed so that the blades are more than 2.5 m above the floor (for fans intended to be mounted at high level).

PARTS IDENTIFICATION

ACCESSORIES

• H. Bolt (2 pcs)
• H.Nut (2 pcs)
• Spring Washer (2 pcs)

1| | Guard clip|
---|---|---|---
2| | Front guard|
3| | Rearguard|
4| | Blade|
5|  | Wing bolt|
6|  | Motor|
7|  | Stand|
8|  | Mounting plate assy|
9| | H. Bolt|
10| | H. Nut|
11|  | Ceiling|
12|  | Supporting plate|
13|  | Set screw|
14|  | Rod|
15|  | Regulator base|
16| | Regulator cover|
17|  | Switch|
18|  | Switch knob|
19| | Capacitor|
20|  | Cover set screw|
21| | Fitting hole|
22|  | Safety wire|

HOW TO ASSEMBLE

1. Fix the rear guard® into the motor guide@

2. Screw the wing bolt (2 pcs) © onto the motor. Tighten firmly
   CAUTION
   Please ensure the wing bolts are fully tightened to avoid the guard from dropping.

3. Fix the blade to the motor shaft. Ensure that the blade slot @fits properly into the motor pin ®·

4. Tighten the blade by turning the ® spinner anti-clockwise.

5. Match front and rear guards and snap them together with both hands.

6. Snap together the front and rear guards according to sequences 1, 2, and 3.

Warning

Do not tangle the motor lead with the power cord.

HOW TO INSTALL THE REGULATOR

Caution: This must be a double pole switch with a minimum 3 mm contact gap in the fixed installation circuit.

1. Use a Philips screwdriver to remove the cover set screw.
2. Fix the regulator base on the wall.
3. Ensure that the wiring follows the wiring diagram.
4. Reassemble the regulator above.

NOTE

The power supply wire connected to the terminal should be equipped with a splice.

HOW TO INSTALL THE FAN

1. Remove the set screw and mounting plate from the stand before installing the fan.

2. Install the mounting plate as shown in figure A.

3. Hold the stand with the set plate facing towards you and ensure to install the safety wire on the left arm.
   Note: Please do not install the right-hand side.

4. Loop the safety wire around the arm and clip the wire as shown in@.
   Mounting plate assy

5. Fix the body to the mounting plate by turning the body so that the hole Q) aligns with the screw hole CD.

6. Tighten the set screw®

WIRING DIAGRAM

OPERATION

• Rotary switch control
• To turn on the fan, simply turn the switch knob to any position (1, 2, 3, 4, or 5).

The oscillation angle can be adjusted to 15, 30, or 50 degrees

• Panasonic Manufacturing Malaysia Berhad. (s100-K)
• No. 3′ Jalan Sesiku 1512′ Shah Alam Industrial Site, 40200 Shah Alam, Selangor Darul Ehsan, Malaysia.
• Made in Malaysia.

Documents / Resources

| Panasonic F-MQ409 Oscillation Auto Fan [pdf] User Manual
F-MQ409 Oscillation Auto Fan, F-MQ409, Oscillation Auto Fan, Auto Fan, Fan
---|---

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>