MiBOXER GU10 RGB+CCT LED Spotlight FUT103Z User Manual
- June 6, 2024
- MiBOXER
Table of Contents
MiBOXER GU10 RGB+CCT LED Spotlight FUT103Z User Manual
Features
This item supports zigbee 3.0 standard protocol with low consumption, strong ability to pair with network automatically and resist interference.
16 Millions of colors to choose
Color temperature 2700K~6500K
Dim brightness/saturation
Product follow Zigbee 3.0 standard protocol
Zigbee 3.0 remote control Control distance 100m (open area)
Smartphone App control (Zigbee 3.0 gateway is needed)
Support third party voice control (Zigbee 3.0 gateway is needed)
Specifications
GU10 RGB+CCT LED Spotlight (Zigbee 3.0)
- Model No.: FUT103Z
- Power: 4W
- Working Temp.: -10~40°C
- Voltage: 100-240V~ 50/60Hz
- Color Temp.: 2700K~6500K
- Light Efficiency: 70LM/W
- Luminous Flux: 280LM
- CRI: ＞80 PF: 0.55
- Lifespan: 50000h
- Beam Angle: 25°
- Control Distance: 100m (open area)
- Size: Φ50*57mm
Instructions
Put the light in the suitable lighting fixture.
Attention:
For lights with a weight significantly higher than that of the lights for
which they are a replacement, attention should be drawn to the fact that the
increased weight may reduce the mechanical stability of certain luminaires and
lampholders and may impair contact making and light retention.
How to control the light via phone App?
Please add zigbee 3.0 gateway to [ MiBoxer Smart ] App firstly
- Connect with power supply.
- Turn on/off light continuously over 3 times , confirm the light with red color in breathe ambience.
- Open [ MiBoxer Smart ] App and add sub-device (see following screenshot).
- You can dim light, group control and ambience control after adding device completely.
Match and Dismatch with zigbee 3.0 remote
stay closer distance between the light and remote
Remote
|
Light
---|---
The remote doesn’t pair with zigbee gateway
| Support match and dismatch light
The remote paired with zigbee gateway|
Only support match and dismatch light which connected with same gateway
Instruction of Matching
- Connect with power supply.
- Ensure the light is always on ( please wait 5 seconds and turn off, turn on again 1 time if the light is in red color with breathe ambience).
- Long press group control ” ” button with 3 seconds untill the indicator of remote flash quickly ( check details in remote instruction).
- Please keep closer for remote and the light which you want to connect ( within 1 meter).
- Matching is done if the light breathe 3 times.
Instruction of Dismatching
- Connect with power supply.
- Ensure the light is always on.
- Long press group control ” Ο ” button with 3 seconds untill the indicator of remote flash slowly (check details in remote instruction).
- Please keep closer for remote and the light which you want to connect ( within 1 meter).
- Dismatching is done if the light breathe 3 times
Please repeat above steps if you are failed
Attention:
- Remote only match or dismatch with one light in one time, it will match or dismatch with the nearest light.
- Remote doesn’t pair with gateway: One light is only controlled by one remote.
- Light doesn’t pair with gateway: It can not be controlled by remote which already paired with gateway.
- If remote and light both connected with gateway: One light can be controlled by many remotes.
Warning
- Ensure voltage is 100-240V~.
- Please turn off power supply while install the light.
- Stay away from high temperature and humid area.
Light can not use in humid area
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>