TARAMPS SMART 3 BASS Power Control System Instruction Manual

TARAMPS SMART 3 BASS Power Control System

Product Information

The TARAMPS ELECTRONICS amplifier is a standard aftermarket electronic equipment designed for use in vehicles. It features a power input of 12V and has various frequency settings such as high pass, low pass, and bass boost. The amplifier has LED indicators to provide information about its status, including battery voltage and amplifier operation. The amplifier is compatible with different speaker configurations, ranging from 0.5 Ohm to 2 Ohms. It has a maximum power output of 3000W RMS and a signal-to-noise ratio of over 90dB. The amplifier also includes protection features like low battery protection and thermal protection.

It is recommended to follow the wiring gauge and fuse guidelines provided in the user manual for proper installation. The amplifier should be installed with caution, ensuring all connections are made with the amplifier turned off. It is also important to check the polarity of the power supply cables and install protective fuses or circuit breakers near the batteries.

Product Usage Instructions

1. Installation:
   • Turn off the amplifier before making any connections to the power supply, input, and output connectors.
   • Use the recommended wire gauge for the positive/negative power supply cable, output cables, and remote cable.
   • Install a protective fuse or circuit breaker near the batteries.
   • Ensure proper polarity of the power supply cables.
   • Make connections to other amplifiers, RCA cables, and head unit as necessary.
2. Operation:
   • Ensure that the amplifier is receiving a 12V power input.
   • Adjust the gain, high pass, low pass, and frequency boost settings according to your preferences.
   • Monitor the LED indicators to check the status of the amplifier.
   • Refer to the user manual for detailed information on LED indicator meanings.

The installation of this product must be made by a qualified professional.

Term of warranty

TARAMPS, located on Abilio Daguano Street 274, Res. Manoel Martins – Alfredo Marcondes, SP – Brazil, ZIP CODE 19180-000, guarantees this product against any defects on terms of project, making, assembling, and/or with solidarity, due to project vices which cause it improper or inadequate to its original use within 12 months from the date of purchase. In case of defect during the warranty period, TARAMPS responsibility is limited to the repairing or substitution of the device of its own making.

This warranty excludes:

• Damaged products by improper installation, water infiltration, violation by unauthorized individuals;
• Tamper or torn warranty seal;
• Defects caused by accessories, modifications or features attached to the product;
• The product with damage from falling, bumps or nature related problems (flooding, lightning, etc.);
• Cases in which the product is not used in adequate conditions;
• Warranty card is not properly filled or torn;
• Costs involving uninstallation, reinstallation of equipment as well as shipment to the factory;
• Damage of any kind, due to problems in the product, as well as losses caused by discontinued use of the product.

Technical assistance

• For international support, check on our website: www.taramps.com.br/en/rede-de-assistencias-tecnicas
• or contact direct the factory support:
  • Phones: +55 18 3266-4050 / +55 18 99749-3391
  • E-mail: angelo.assistencia@taramps.com.br

Smart Bass Line Presentation

• Multi-impedance: Featuring new control technology and new functions, the SMART 3 BASS has 3000W
• RMS rated power in the range of 0.5 to 2 Ohms: (0.5 – 1 – 1.33 – 1.5 – 1.67 and 2 Ohms with same power);
• SMART LEDS: LEDs output signal level indicator on top of product;
• RCA inputfor up to 4V RMS: Input gain adjustment that allows head units up to 4V RMS output level;
• Dual RCA IN / OUT Input: RCA connector with input and output function, eliminates the needing of “Y” cables for send the same unput signal to another amplifier;
• Power connector for cables up to 1/0 AWG: Allows the use of power cables with larger gauge (up to 50mm%) for higher performance;
• AUTO-Restart Protections: The amplifier automatically restarts after a protection event;
• RAMP audio initialization: After turning on the amplifier, audio is released gradually (ramp).

Introduction

Read this manual before preparing the product. In case of doubt, contact our technical support: (18) 3266-4050 or www.taramps.com.br.

At the end of its useful life, this product must not be disposed of in household waste. Look for an electronic equipment collection or recycling center for proper disposal.

Declaration of Conformity

• TARAMPS ELECTRONICS LTDA
• Alfredo Marcondes – SP Brazil

Hereby, Taramps Electronics Ltda declares that the product SMART 3 BASS complies with the Directive 2014/30/EU, according with the following harmonized standard:

• -EN 50498:2010 Electromagnetic compatibility (EMC) –
• Product family standard for aftermarket electronic equipment in vehicles

The full text of the EU Declaration of Conformity is available at the following Product Page on Internet.

Safety requirements

To ensure proper use, please read through this manual before using the amplifier. It is specially important that you know the WARNINGS and CAUTIONS contained here.

• The installation of this amplifier must be done by a qualified professional.
• Wear safety glasses, insulated gloves and correct tools for installing this product.
• This amplifier is for use with 12V batteries. Always check the voltage before installing.
• This amplifier must be installed in a firm place with at least 1″ space around the heatsink for proper heat spreading.
• Never install the amplifier in places exposed to dust, humidity and water. Pay attention to install it far from fuel tank, fuel lines, heat sources and other parts of vehicle.
• Be sure to install protection fuse or a circuit braker near to battery. Follow the ampere rating as indicated here in this manual. Use of improper fuse or circuit breaker could result in overheat, smoke, damage to product, injury or burns.
• Avoid running wires over or through sharp edges. Use rubber or plastic grommets to protect any wires routed through car’s body.
• Before make any connection to amplifier, disconnect the battery negative terminal.
• When in use, the external surface of may amplifier becomes hot. Avoid touching the heatsink area and keep childrens far from the amplifier.
• This amplifier may produce high sound pressure levels. Avoid continuous exposure to levels over 85dB to prevent permanent hearing loss.
• Output connections for speakers may have voltage levels when the amplifier is operating.
• Make sure that the amplifier is turned OFF before proceed any connection or disconnection in this terminals.
• If you want to dispose this amplifier, don’t throw it on domestic waste. It must be collected by an used electronic product disposal service for proper recycling.

Safety

As you read this manual, pay attention to the safety symbols.

CAUTION: This symbol with “CAUTION” is intended to alert the user to the presence of important instructions. Failure to heed the instructions will result in risk of injury to user or product damage.

Taramps reserves the right to modify the contents of this document at any time without prior notice and does not have the obligation to apply the changes in units which were previously produced.

Functions, inputs & outputs

1. IN: Input of signal to be amplified. Connect the to the RCA output of the Head Unit using good shielded cable to avoid noise interference.
2. OUT: Audio signal output. Sends the same input (IN) signal to another amplifier, allowing cascading.
3. GAIN: Adjusts the input sensitivity of the amplifier, allowing a perfect adjustment to the output signal levels of various head units models on the market. It is possible to adjust from 4V (minimum sensitivity) to 0.2V (maximum sensitivity).
4. CROSSOVER
   • HIGH PASS FILTER (HPF): Variable setting from 8Hz to 30Hz, which determines the start of the amplifier’s operating frequency.
   • LOW PASS FILTER (LPF): Variable setting from 60Hz to 200Hz, which determines the end of the amplifier’s operating frequency.
5. BASS BOOST
   • FREQ: Set the frequency of bass boost from 35Hz to 60Hz.
   • BOOST: Set the boost level from 0 to + 10dB at the frequency set in FREQ.
6. MONITOR: An accessory connection that has the function of monitoring the amplifier, displaying clipping and protection status. (Included accessory).
7. SPEAKER: SPEAKER: Output (positive and negative) for connecting transducers (speakers). Follow the indicated polarity.
   • For speaker associations, the impedance to consider is the resulting impedance:

CAUTION: Due to the presence of voltage at the output terminals when the product is turned on, avoid contact with them. Risk of electric shock.

Power supply connector

1. SMART COOLER: This amplifier has two internal ventilation fans. For perfect functioning, the amplifier must be installed in a cool and aired place with at least 1” (25mm) space around the heatsink for proper heat spreading. The usually working temperature of amplifier is 65°C.
   • CAUTION: The fan and ventilation openings are responsible for cooling the amplifier when it is in use, so it cannot be obstructed.
2. POSITIVE POWER SUPPLY: Use a minimum 4 AWG up to maximum of 1/0 AWG cable direct from the positive battery terminal, with fuse or circuit breaker (200A), as close to it as possible.
3. TERMINAL REMOTE: It must be connected to the remote output of the head unit using a 18 AWG cable.
4. NEGATIVE POWER SUPPLY: Use a cable of minimum 4 AWG up to maximum of 1/0 AWG as short as possible, connected to the negative battery pole.

We recommend that all cables have tinned ends for better electrical contact. In case of power bus bar using, avoid tightening with extenders on the allen wrench, as excessive torque may break the the terminal.

CAUTION: Before making any connections to the power terminals, make sure that the negative (-) of the vehicle battery is disconnected.

LEDS indicators & protection system

• The thermal protection waits for cooling before restarting.
• If it goes into protection, the amplifier will automatically restart.

Example

Low Battery Protection: Working amplifier Red LED (LED Monitor) or Smart LEDS, flashes 2x Red LED (LED monitor) or Smart LEDS, flashes 2× Amplifier restarts.

Installation

CAUTION: All connections to power supply, input and output connectors must be carried out only with amplifier off.

Recommended wire gauge & fuse

• Positive / negative power supply cable ____Min. 4 AWG / Max.1/0 AWG
• Output cables wire gauge____9 AWG
• Remote cable ____ 18 AWG
• Protection fuse or circuit breaker____200A

Calculated considering a maximum length of 4m. Distance greater than this, you will need to increase the cable gauges.

Caution

• Using wire gauges below the recommendation will result in power loss and overheating of wiring.
• Check polarity and never reverse power supply cables due to the risk of damage to the amplifier.
• It is compulsory to install a protection fuses or circuit breakers as close as possible from batteries.

• Examples of connections in the power supply input.

Note: Required battery bank capacity: At least 200Ah

Caution: This equipment is not suitable for use in places where children may be present.

Technical features

• Output Impedance Range: 0.5 Ohm ~ 2 Ohms
• Number of Channels: 01
• Output Power / @14.4VDC*
  • 0.5 OHM: 3000W RMS
  • 1 OHM: 3000W RMS
  • 2 OHMS: 3000W RMS
  • 4 OHMS: 1700W RMS
  • Input Sensitivity: 4V ~0.2V
• Signal- to-noise Ratio: >90dB
• Frequency Response: 8Hz ~ 200Hz (-3dB)
• Crossover HPF (High Pass Filter): 8Hz ~ 30Hz (-12dB/8ª) Variable
• LPF (Low Pass Filter): 60Hz ~ 200Hz (-12dB/8ª) Variable
• Bass Boost:
  • Freq.: 35Hz ~ 60Hz
  • Boost: 0 ~ +10dB
• Efficiency: 75%
• Input Impedance: 10K Ohms
• Protection System: Output short-circuit, low/high supply voltage and Thermal protection
• Minimum Supply Voltage: 9VDC
• Maximum Supply Voltage: 17VDC
• Idle Consumption: 1.10A
• Musical Consumption / @14.4VDC: 190A
• Rated Power Consumption: 278A
• Dimensions (W x H x L): 9.37″ x 2.80″ x 9.45″
• Weigth:  6.60lb

Contact

• +55 18 3266-4050
• Manufactured by: TARAMPS ELECTRONICS LTDA
• CNPJ / TAX ID: 11.273.485/0001-03
• R. João Silvério, 121 • Res. Manoel Martins
• Alfredo Marcondes – SP
• Indústria Brasileira – Made in Brazil
• www.taramps.com.br

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>