Strand 12 – 12 X 30 Watt RGBA+Lime 12-Cell Linear LED Bar User Guide
- June 6, 2024
- Strand
Table of Contents
Strand 12 - 12 X 30 Watt RGBA+Lime 12-Cell Linear LED Bar User Guide
OVERVIEW
This document provides basic setup instructions and safety warnings for the following product(s):
Aurora 12 LED Strip 64508-002
INSTALLATION AND SETUP
MOUNTING
The unit should be mounted via its screw holes on the bracket. Always ensure that the unit is firmly fixed to avoid vibration and slipping while operating. Always ensure that the structure to which you are attaching the unit is secure and is able to support a weight of 10 times of the unit’s weight. Always use a safety cable that can hold up to 12 times the weight of the unit when installing the fixture. The luminaire must be mounted by professionals.
CONTROL PANEL
-
LCD display – shows menu and selected function
-
Buttons:
MENU – to select programming functions
DOWN – to go forward in selected functions
UP – to go backward in selected functions
ENTER – to confirm the selected function -
DMX IN – 5-pin XLR cable to link the DMX console
-
DMX OUT – 5-pin XLR cable to link next fixture
-
POWER IN – connects to power supply
-
POWER OUT – connects to next fixture
-
ArtNet/sACN – RJ45 connector to link ArtNet/sACN from source
QUICK REFERENCE DMX MAPS
The Aurora 12 LED Strip has the following DMX modes:
- SSCC Mode (Default) 1 Zone
- SSCC Mode 4 Cell
- SSCC Mode 12 Cell
- SQCC Mode 1 Zone
- SOCC Mode 1 Zone
- SOCC Mode 4 Cell
- SOCC Mode 12 Cell
Quick reference maps for each mode can be found on the following pages. For full DMX maps, refer to the user manual.
SSCC MODE (DEFAULT) 1 ZONE
SSCC MODE 4 CELL
SSCC MODE 12 CELL
SQCC MODE 1 ZONE
SOCC MODE 1 ZONE
SOCC MODE 4 CELL
SOCC MODE 12 CELL
SAFETY WARNINGS AND NOTICES
Read this user manual in full before attempting to install, operate or maintain the fixture to which it relates. This user manual is intended to provide general guidance to such suitably qualified personnel. Installation and operation of the fixture are to be performed by qualified personnel only.
When using electrical equipment, basic safety precautions should always be followed including the following:
READ AND FOLLOW ALL SAFETY INSTRUCTIONS.
- For indoor, dry location use only. Do not use outdoors unless fixture is suitably IP rated.
- Use safety tether when mounting.
- Equipment should be mounted in locations and at heights where it will not be readily subjected to tampering by unauthorized personnel.
- Not for residential use. Do not use this equipment for other than intended use.
- Note distance requirement(s) from combustible materials or illuminated objects. Do not mount near gas or electric heaters.
- Install only in locations with adequate ventilation. Ensure sure that ventilation slots are not blocked.
- Ensure that the voltage and frequency of the power supply match the power requirements of the fixture.
- The fixture must be earthed/grounded to the appropriate conductor.
- Do not operate fixture outside the specified ambient temperature range.
- Do not connect the fixture to any dimmer pack.
- The use of accessory equipment not recommended by the manufacturer may cause an unsafe condition and void warranty.
- Refer service to qualified personnel. This fixture contains no user serviceable parts.
- Prior to first use, carefully inspect fixture to ensure no damage has occurred during shipping.
- Materials used in the manufacturing process can cause strong odors when the product is new. These odors dissipate over time Prior to each use, carefully inspect power cables and replace any damaged cables.
- Exterior surfaces of the luminaire will be hot during operation. Take appropriate precautions.
- Continuous use of the fixture may shorten the lifespan. Power down the fixture when not in use.
- Do not cycle power on and off repeatedly. Disconnect mains power if the fixture is not used for an extended period.
- Clean fixtures regularly, particularly when working in a dusty environment.
- Never touch power cables or wires while the fixture is powered on.
- Avoid entangling power wires with other cables.
- In the event of a serious operating problem, immediately discontinue using the fixture.
- It is hazardous to operate luminaires without lens or shield. Shields, lenses, or ultraviolet screens shall be changed if they have become visibly damaged to such an extent that their effectiveness is impaired, for example, by cracks or deep scratches.
- Original packing materials can be reused for transporting the fixture.
- Do not look directly at the LED light beam while the fixture is on.
- This is a Class A product. In a domestic environment this product may cause radio interference, in which case, the user may be required to take adequate measures.
- The light source contained in this luminaire shall only be replaced by the manufacturer or service agent or similarly qualified person.
SAVE THESE INSTRUCTIONS
WARNING : Refer to National Electrical Code® and local codes for cable specifi cations. Failure to use proper cable can result in damage to equipment or danger to personnel.
COMPLIANCE NOTICE
FCC DECLARATION OF CONFORMITY
This equipment has been tested and found to comply with the limits for a Class
A digital device pursuant to Part 15 of FCC Rules. These limits are designed
to provide reasonable protection against harmful interference when this
equipment is operated in a commercial environment. This equipment generates,
uses, and can radiate radio frequency energy and, if not installed and used in
accordance with Vari-Lite Strand system, service, and safety guidelines, may
cause harmful interference to radio communications.
As tested under this standard:
*FCC 47CFR 15B clACEI**
Issued:2009/10/01 Title 47 CFR Part 15 Subpart B Unintentional Radiators Class
A
Operation of this equipment in a residential area is likely to cause harmful
interference, in which case the user will be required to correct the
interference at his/her own expense.
EU DECLARATION OF CONFORMITY
We, Vari-Lite LLC., 10911 Petal Street, Dallas, Texas 75238, declare under our responsibility for the products contained herein are in conformity with the essential requirements of the following European Directives and harmonized standards:
Low Voltage Director (LVD), 2006/95/EC
EN 60589-2-17:1984+A1:1987+A2:1990 used in conjunction with
60598-1:2008/A11:2009
©2021 Signify Holding. All rights reserved.
All trademarks are owned by Signify Holding or their respective owners.
The information provided herein is subject to change, without notice. Signify
does not give any representation or warranty as to the accuracy or
completeness of the information included herein and shall not be liable for
any action in reliance thereon. The information presented in this document is
not intended as any commercial offer and does not form
part of any quotation or contract, unless otherwise agreed by Signify. Data
subject to change.
CUSTOMER SERVICE
If you have any questions regarding this product, please contact Customer
Service by phone at +1 214-647-7880 or
by email at
entertainment.service@signify.com.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>