KERBL 297582 Winter Gloves User Manual
- June 3, 2024
- KERBL
Table of Contents
297582 Winter Gloves
power grab Thermo W
| ref.no. | size |
|---|---|
| 297582 | 8 / M |
| 297583 | 9 / L |
| 297584 | 10 / XL |
| 297585 | 11 / XXL |
ISO 21420:2020 abweichen
As the gloves are adjusted to special purposes, the lengths may deviate from
the requirements of EN ISO 21420:2020.
Category II – Mechanical risks
Protection from cold
UK: SATRA Technology Centre Ltd, Wyndham Way Telford Way, Kettering,
Northamptonshire, NN16 8SD Approved Body: 0321 This product contains latex,
which could cause allergic reactions.
Instructions for use
Results of the EN388:2016+A1:2018 mechanical test
| Abrasion resistance: | 1 (min 0 / max 4) |
|---|---|
| Blade cut resistance (Coupe – Test): | 2 (min 0 / max 5) |
| Tear resistance: | 3 (min 0 / max 4) |
| Puncture resistance: | 1 (min 0 / max 4) |
| Blade cut resistance (TDM): | X (min A/max F) |
Test results of risks from cold according to EN 511
Convected cooling: 0 (min 0 / max 4)
Contact cooling: 1 (min 0 / max 4)
Waterproof properties: X (0 / 1)
The sign X, instead of a number, means that the glove is not designed for the use covered by the corresponding test. Results only from samples of glove palms with inserted lining. The overall classification of the glove does not necessarily reflect the performance of the outermost layer.
Care and Cleaning:
The service stages mentioned are based on tests that were carried out exclusively on unused gloves. Transfer of the results on gloves aftercare treatment is not possible. The manufacturer accepts no liability for changes to the properties. For donning, check the integrity of the glove and the picked size fits the hand. For doffing, ease the glove of one hand before removing the second glove to reduce the risk of contamination.
Packaging and storage:
This article is supplied in uniform sales packaging made from recyclable cardboard. PE bags or similar environmentally friendly coverings are the smallest packaging unit. The gloves must be stored correctly, i.e. in boxes in dry rooms. The properties can be altered by influences such as humidity, temperature, and light, as well as natural alterations to the materials over a period of time.
Aging:
It is not possible to give an expiry date, as this can be dependent on the degree of wear, use, and the area in which the gloves are used.
General information / Risk assessment:
The glove types named here meet the requirements of EU regulation 2016/425 and
is compliant with the above-mentioned harmonized/designated standards, EN ISO
21420:2020, EN388:2016+A1:2018, EN 511:2006. While selecting equipment, the
user should perform risk analysis based on the intended use and determine
suitability based on the product’s test standards and protection levels
obtained. Laboratory tests offer aid to the selection, however, they cannot
take the actual workplace conditions into account. It is therefore the
responsibility of the user and not the manufacturer to test the suitability of
a certain glove for the planned area of use. Gloves for general light handling
in wet conditions. The equipment provides protection against moderate
mechanical risks. The maximum wear time depends on the activity being carried
out and the person. The glove offers no protection against perforation with
sharp objects, e.g. injection needles. No gloves should be worn if there is a
risk of becoming caught in moving machine parts. The gloves lose their heat-
insulating properties when wet.
Manufacturer
Towa Corporation
227 Tsubuku-Honmachi,
Kurume, Fukuoka, 830-0047, JAPAN
Declaration of Conformity
www.towagloves.com/certifications/eu-declaration-of-
conformity
Importer
Albert Kerbl GmbH Felizenzell 9 84428 Buchbach, Germany
www.keron-online.com
Kerbl UK Ltd Lands End Way
Oakham, Rutland
LE15 6RF, UK
www.kerbl.co.uk
References
- IIS7
- Home - Kerbl UK Ltd
- Arbeit und Sicherheit - Albert Kerbl GmbH
- CERTIFICATIONS | TOWA CORPORATION
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>