Sytech SY-XTR27BT TWS Wireless Bluetooth Speakers User Manual
- June 6, 2024
- Sytech
Table of Contents
Sytech SY-XTR27BT TWS Speakers User Manual
Welcome
Thank you for purchasing the new Wireless Party speaker SY-XTR27BT “Powerfluent” series. Please read this manual carefully before operating your product. And pay close attention to the precautions which are mentioned below. Store this user manual in a safe place for future reference.
Safety Precautions
Points to observe for safe usage
Read this manual carefully before using the product. They contain
instructions on how to use this product in a safe and effective manner. SYTECH
will not be responsible for problems resulting from failure to observe the
instructions in this manual.
Turn off the device immediately in case of a problem.
Failure may cause personal injury or damage to the product.
Return it to your authorized SYTECH dealer for repairing.
Product cleaning.
Use a soft dry cloth for periodic cleaning of the product. For more severe
stains, please dampen the cloth with water only. Any other product such as
alcohol, benzene, may damage the paint or the plastic.
Temperature
Make sure before using the product, the room temperature is between +35ºC
(+95ºF) and -10ºC (+14ºF)
Maintenance.
If you have problems, do not attempt to repair the unit yourself.
Surface
Place the unit on a flat surface.
Leave enough space around the unit for a proper ventilation.
Heat.
Do not place the product near any heat sources or to direct sunlight.
Accessories.
Use only supplied accessories
Charging the speaker
- Connect the AC adaptor provided with your speaker. (DO NOT USE ANY OTHER AC ADAPTOR OTHER THAN THE ONE PROVIDED).
- Plug in the AC adaptor jack into the DC 5V input connector located on the top panel of the speaker.
- The Charge LED light will turn to red indicating the battery is being charged.
- Once the battery is fully charged, the LED light will turn off.
- Disconnect the AC adaptor and use your speaker with the batteries.
Remote Control Functions
- Power
- Mode. Input selection (AUX-USB-TF-FM-BT)
- Mute
- Play / Pause. FM Auto scan
- Next track, Next FM preset
- Previous track, Previous FM preset
- Equalizer effects
- Decrease volume
- Increase volume
- Numerical keys
- Repeat function
- USB Micro SD function
“This picture is for reference purposes only”
- Under normal circumstances, the remote control should be aimed directly at the infrared receiver window of the unit. The maximum distance for the remote-control operation is approximately 6 meters and within a 30° angle.
- When operating the remote control, aim the remote control at the infrared receiver window of the unit and ensure that there are no obstacles between the remote control and the unit.
- If the remote receiver is facing direct sunlight, it may fail. In this case, move the speaker away to avoid the light.
- Avoid mixing old and new batteries. Replace the remote-control batteries regularly.
Wired microphone usage
- Connect the supplied wired microphone to the MIC input jack located on the top panel of the speaker (5).
- Control the Volume of the MIC by rotating the volume knob.
Functions and connections
- CHEERS EFFECT
- CLAPPING EFFECT
- LAUGHTER EFFECT
- MUAH EFFECT
- MIC. INPUT
- DC 5V. INPUT
- LED LIGHTS ON/OFF
- MODE
- PREVIOUS
- PAUSE/PLAY/TWS
- NEXT
- USB PORT
- MICRO SD SLOT
- AUX INPUT
- MAIN POWER SWITCH
- VOLUME CONTROL
- LED DISPLAY
USB & Micro-SD Slot
USB FUNCTION:
- Make sure your USB flash is formatted as FAT32.
- Insert the USB flash into the USB port of the speaker system
- The unit should detect the USB automatically and play the first track
- If in the case the USB does not start automatic playback, press the Input button and select MP3 mode.
- If you wish to pause the music, simply press the pause button
- To select the next track, simply press the “Next” button
- To select the previous track, simply press the “Previous” button
Note:
- Make sure the music files are MP3, WAV format or else the music system will not be able to read the files.
- Make sure the music files are recorded to the root directory.
- It is advisable to remove unnecessary files for faster reading of the content.
MICRO-SD CARD FUNCTION:
- Make sure your Micro-SD card is formatted as FAT32.
- Insert the Micro-SD card into the TF slot of the speaker system
- The unit should detect the Micro-SD card automatically and play the first track
- If in the case the Micro-SD card does not start automatic playback, press the Input button and select MP3 mode.
- If you wish to pause the music, simply press the pause button
- To select the next track, simply press the “Next” button
- To select the previous track, simply press the “Previous” button
Bluetooth function
- Select the BLUETOOTH mode by pressing the “MODE” switch on the top panel of the unit or from the remote control itself.
- Please ensure the Bluetooth device you wish to connect has the Bluetooth function enabled and visible.
- Start the scan function from your device and search for “SY-XTR27BT”.
- Once you have found the device, press on it and connect the speaker with the device.
- When the connection is successful, a “tick” tone will be heard. If the speaker cannot be connected, please restart the speaker or the device and try again.
- After the connection is successfully established, you can begin to play music. To ensure continuous stability of the music signal, try to keep the Bluetooth device and the mobile phone facing one another.
- The distance for the Bluetooth signal range is up to 14 meters when no obstacles in between.
FM Radio function
- Press the “MODE” button to switch to FM mode.
- Press the “Pause/Play” button to start the automatic search of the stations.
- The unit will start to search all the main stations and will store them automatically.
- Once the scan search has finalized, press the “NEXT” or “PREVIOUS” buttons to access to the stored channels.
- The unit will store up to 40 presets.
Note: The FM stations can only be stored automatically. The position of the channel store number will start from the lowest FM frequency to the highest. The pre-set memories cannot be memorized manually.
TWS Function
The TWS function allows you to connect two speakers at the same time and lets you enjoy “True Wireless Stereo” music.
- Select the Bluetooth mode on the two speakers.
- Long press the “Play/Pause/TWS” button during 3 or 4 seconds on one of the speakers.
- A beep sound will be heard confirming the pairing of the two speakers.
- Connect your mobile device via Bluetooth the speaker
- Play the track from your mobile device and enjoy True Wireless Stereo experience as each speaker will act as left and right.
- To exit the TWS mode, simply long press the “Play-Pause – TWS” button.
Main technical specifications
Basic Specifications
- 2 x 8” Woofer + 1 x 1” Tweeter
- USB/Micro-SD/FM/Bluetooth function
- 1 x Microphone input
- 1 x Aux input
- LED display
- Remote control
- RGB light on woofer grill
- Output power: 30W RMS.
- Output power: 250W PMPO
- TWS Function (True Wireless Stereo)
- Built in rechargeable battery. 3000mAh 3.7V
Bluetooth Specifications
- Bluetooth Version: V5.0 + EDR
- Bluetooth Support: 5.0
- Bluetooth Profiles: A2DP, AVRCP
- Bluetooth pairing name: SY-XTR27BT
USB/Micro-SD card Specifications
- 2.0 USB Port (Max Capacity: 32GB)
- SD Card Slot (Max Capacity: 32GB)
- Compatible Audio Formats in USB: MP3 / WAV
- Compatible Audio Formats in SD: MP3 / WAV
Technical Specifications
-
Output power: 250W PMPO
-
Output power: 30W RMS
-
SNR: 70dB±3dB
-
Frequency response: 45Hz-18KHz
-
Power supply: DC 5V.-1A / AC110V-240V, 50/60Hz
-
Working time: 2-3 hours (Depends on Volume level)
-
Charging time: 3 to 4 hours
-
Above specifications are of “SY-XTR27BT are for reference purpose only.
-
Due to continuous product development, specifications may be subject to change without prior notification.
-
Do not expose to adverse weather conditions (Such as rain or high temperatures) as it can cause malfunctions
Simple troubleshooting
Try the troubleshooting steps below if you are having problems while using your speaker. If problems still exist, please look for a qualified technician or contact Sytech technical department.
To prevent electric shock or damage the speaker, do not repair by yourself.
Declaration of Conformity
Manufacturer Name: Satyatrade S. L.
Address: Pol.Ind.La Raya. C/ Guadalquivir, 2.
Camarma de Esteruelas, 28816 Madrid
Tel: 902 430 967
Fax: 91 8864285
NIF: B83254763
Manufacturing country: China
Description: Party speaker “Powerfluent” serie
Sytech® SY-XTR27BT complies with the following directives:
RED Standard: Directive 2014/53/EU
ROHS Standard: Directive 2011/65/EU Restriction of Hazardous Substances
Signed: Ajeet Nebhwani Utamchandani
Sole Administrator
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>