NINJA Professional XL Food Processor User Guide
- June 9, 2024
- Ninja
Table of Contents
PROFESSIONAL XL
FOOD PROCESSOR
QUICK START GUIDE
Professional XL Food Processor
Please make sure to read the enclosed Ninja® Safety Instructions prior to using your unit.
USING THE CHOPPING & DOUGH BLADE ASSEMBLIES
PRECISION PROCESSOR® BOWL & LID WITH 3-PART FOOD PUSHER| CHOPPING BLADE
ASSEMBLY| DOUGH BLADE ASSEMBLY
---|---|---
| |
BLADE ASSEMBLY
1. Place Precision
Processor Bowl on base and turn clockwise to lock in place.| 2. Holding the
blade assembly by the top of the shaft, install it in bowl.| 3. Place
ingredients in bowl. Place lid on bowl and turn clockwise to lock in place.
---|---|---
| |
PROCESS & ENJOY
Once the Precision Processor Bowl is locked onto the base, plug in the unit,
then press the Power button ****to turn the unit on.
1. Select desired program to begin processing.| 2. When processing is
complete, press button on feed
chute lid near handle to unlock. Turn lid counterclockwise and lift from bowl.
Remove blade assembly before emptying bowl.| 3. Remove bowl from base by
turning it counterclockwise, then lifting it up.
---|---|---
| |
NOTE: Large food pusher must be inserted in the feed chute for the unit
to run. For thinner recipes such as sauces and chopping, make sure all 3 parts
of the pusher are installed to avoid splatter.
WARNING: Chopping Blade Assembly is sharp and not locked in place. Before
pouring, carefully remove Chopping Blade Assembly. Failure to do so will
result in a risk of laceration. Refer to the Ninja Safety Instructions for
additional information.
USING THE DISC ASSEMBLIES
PARTS
PRECISION PROCESSOR® BOWL & LID WITH 3-PART FOOD PUSHER| DISC SPINDLE|
REVERSIBLE SLICING/SHREDDING DISC
---|---|---
| |
DISC ASSEMBLY
1. Place Precision Processor® Bowl on base and turn clockwise to lock in
place.
Install the spindle, then place the disc on the spindle.| 2. REVERSIBLE
SLICING/SHREDDING
Use plastic grip to place disc over spindle with the desired output facing up.
Use the side labeled SLICER for slicing and the side labeled SHREDDER for
shredding.
---|---
|
FOOD PREP
If using the small or medium feed chute, trim ingredients to fit the feed
chute height.
If using the larger feed chute, DO NOT exceed the CHUTE MAX FILL line on the
large feed chute. Unit will not run if ingredients exceed this line.
Cut both ends off ingredients to create flat surfaces. Trim tapered ingredients like carrots to make them more symmetrical.
NOTE: Ensure cheese is well chilled before slicing/shredding. DO NOT
slice or shred frozen cheese.
NOTE: Keep ingredients as steady as possible when pushing through the
feed chute.
This will help minimize waste.
PROCESS & ENJOY (DISCS)
Once the Precision Processor® Bowl is locked onto base, plug in the unit, then
press the Power button **to turn the unit on.
IMPORTANT:** As a safety feature, the large food pusher must be inserted in
the feed chute for the unit to run.
-
Place feed chute lid on bowl and turn clockwise. Based on the ingredient, use the smallest possible feed chute opening for best slicing and shredding results.
-
A.
If using the small or medium feed chute opening, select DISC or LOW. The disc will begin spinning. Add ingredients through the feed chute on the lid. 2 B.
If using the large feed chute opening, place ingredients up to, but not exceeding, the CHUTE MAX FILL line. Insert the pusher into the feed chute, then select DISC or LOW. The disc will begin spinning. IMPORTANT: Use only the DISC program or LOW setting when using the disc assemblies. -
The disc will automatically stop spinning at the end of the program. Wait for disc to stop turning, then press the button on the feed chute lid near the handle to unlock. Turn lid counterclockwise and lift lid from bowl.
-
Remove the disc assembly by grasping the plastic grip, then remove the disc spindle.
Remove bowl from base by turning it counterclockwise, then lifting it up.
CLEANING
| Dishwasher: The bowl, lid, disc, and blade assemblies are dishwasher safe.
Ensure the blade assembly is removed from the bowl before placing in the
dishwasher. Exercise care when handling blade assemblies.
---|---
| Hand-washing: Wash bowl, lid, disc, and blade assemblies in warm, soapy
water.
Exercise care when washing the blade assemblies. Use a dishwashing utensil
with a handle to avoid direct hand contact with blades. Rinse and air-dry
thoroughly.
WARNING: Always unplug the base before cleaning.
AUTO-IQ® PROGRAMS
Intelligent preset programs combine unique blending and pausing patterns that
do the work for you.
Once an Auto-iQ program is selected, it will start immediately and
automatically stop when processing is complete. To stop processing before the
end of a program, press the currently active button again.
NOTE: Program run times vary from a few seconds to just over a
minute.
CHOP
Timed pulses and pauses give you consistent chopping results.
Run program once for a large chop, twice for a small chop, and three times for
a mince. Use with chopping blade assembly.
DOUGH
Ideal for creating delicious dough, from pie to pizza to cookie doughs. Use
with the dough blade assembly.
NOTE: Use PULSE to add mix-ins, such as chocolate chips or raisins, after
dough program has completed.
PUREE
Create anything from silky-smooth sauces to the perfect hummus.
Use with the chopping blade assembly or nesting workbowl with small chopping
blade assembly.
DISC
Slice and shred a variety of ingredients, such as vegetables, cheese.
Use with reversible slicing/shredding disc.
MANUAL PROGRAMS
LOW and HIGH: When selected, each of these speeds runs continuously for 60
seconds. They do not work in conjunction with any Auto-iQ programs
PULSE: Offers greater control of pulsing and processing. Operates only
when PULSE is pressed. Use short presses for short pulses and long presses for
long pulses.
IMPORTANT: DO NOT run the unit on HIGH if using the dough blade or disc
assemblies.
The unit is NOT intended to crush ice. Refer to the warnings in the Safety
Instructions.
GET TO KNOW THE ATTACHMENTS
BLADE ASSEMBLIES
| CHOPPING BLADE ASSEMBLY | DOUGH BLADE ASSEMBLY |
|---|---|
3-PART FOOD PUSHER
3-PART FOOD PUSHER:
The 3-part food pusher separates into small, medium, and large food pushers to
guide ingredients through the different-sized feed chute openings. Use the
small feed chute opening (which also doubles as a measuring cup) for
ingredients like carrots, the medium feed chute for ingredients like cucumbers
and zucchini, and the large feed chute for ingredients like potatoes.
NOTE: As a safety feature, the large food pusher must be inserted in the
feed chute for the unit to run. DO NOT exceed the CHUTE MAX FILL line on the
large feed chute. Unit will not run if ingredients exceed this line.
DISC ASSEMBLIES
REVERSIBLE SLICING/SHREDDING:
The reversible slicing/shredding disc is perfect for outputs like thinly
sliced cucumbers and shredded carrots. Face the side labeled SLICER up for
slicing and face the side labeled SHREDDER up for shredding.
DISC SPINDLE:
Install disc spindle onto the gear shaft of the Precision Processor® Bowl to
use the disc assemblies.
STORAGE BOX:
(not included with all models)
Easily and safely store the disc assemblies, disc spindle, and dough blade
assembly in the storage box. To purchase, visit
ninjaaccessories.com.
Scan the code for online help, FAQs, and How-To Videos. ninjakitchen.ca
https://qr.ninjakitchen.com/xlprocessor?qr=1
For questions or to register your product, visit us online at ninjakitchen.ca
@ninjakitchencanada
© 2022 SharkNinja Operating LLC.
AUTO-IQ, NINJA, and PRECISION PROCESSOR are registered trademarks of
SharkNinja Operating LLC.
NF700C_QSG_E_MP_Mv3
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>