TCL TW30-3BLCEU4 S600 Moveaudio Wireless Earphone User Manual
- June 6, 2024
- TCL
Table of Contents
TW30-3BLCEU4 S600 Moveaudio Wireless Earphone
Hi! Let’s get started.
TW30 MOVEAUDIO S600
User manual
Contents
1 Important safety instructions
3
Hearing Safety General safety information
2 Welcome
4
What’s in the box Overview of the truly wireless earphones
3 Charge
5
Charge the battery Check the battery status
4 Connect your earphones
6
Google Fast Pair Manual Pairing Pairing your earphones via app
5 Use your earphones
7
Wear the earphones Power your earphones on or off Wearing detection Reconnect your earphones to your smartphone or Bluetooth® device Music control Call control Voice assistant ANC control Low battery prompt Reset the earphones
6 Firmware update
10
7 Notice
11
Compliance notice Declaration of conformity Remove the integrated battery Disposal of your old product and battery
8 Notice for US and Canada
12
Compliance notice for US Compliance notice for Canada
9 Trademarks
13
10 FAQ
14
1 Important safety instructions
Hearing Safety
Caution:
Danger of explosion if battery is incorrectly replaced. Replace only with the
same or equivalent type.
Operating temperature and humidity:
· Operate or store in a place where temperature is between 0ºC (32ºF) to 45ºC
(113ºF) (up to 90% relative humidity with no condensation).
· Battery life may be shorter in high or low temperature conditions.
Danger
To avoid hearing damage, limit the time you use earphones at high volume and
set the volume to a safe level. The louder the volume, the shorter the safe
listening time is.
To prevent accidents and damage to ears: · Listen at reasonable volumes for
reasonable periods of
time. · Be careful not to adjust the volume continuously upwards
as your hearing adapts. · Do not turn up the volume so high that you can’t
hear
what’s around you.
General safety information
To prevent damage and malfunctions: · Do not expose earphones to excessive
heat. · Do not drop your earphones. · The earphones are resistant to dripping
and splashing
water. The charging case is not waterproof. Before putting the earphones into
the charging case, thoroughly wipe off any moisture. · Do not submerge your
earphones in water. · Do not use any cleaning agents containing alcohol,
ammonia, benzene, or abrasives. · If cleaning is required, use a soft cloth,
if necessary dampened with a minimum amount of water or diluted mild soap, to
clean the product.
Battery precautions: · The integrated battery shall not be exposed to
excessive
heat such as sunshine, fire or the like.
Charging temperature Charging with the charging case when temperature is
between 0ºC (32ºF) to 45ºC (113ºF)
Medical device The earphones and charging case contain magnets. The American
Heart Association (US) and the Medicines and Healthcare Products Regulatory
Agency (UK) both warn that magnets can affect the operation of implanted
pacemakers, cardioverters, defibrillators, insulin pumps or other electro
medical devices (collectively, “Medical Device”) within the range of 15 cm (6
inches). If you are a user of any of these Medical Devices, DO NOT USE THIS
EARPHONES AND CHARGING CASE UNLESS YOU HAVE CONSULTED WITH YOUR PHYSICIAN.
Liability: · This product is designed for use with mobile devices that
support Bluetooth® standard specified by Bluetooth® SIG, Inc. and are
compatible to the following Bluetooth® profile:
Bluetooth® profile · HFP – Hands-free profile · A2DP – Advanced audio
distribution profile (Bluetooth®
stereo supported) · AVRCP – Audio video remote control profile
· This radio equipment operates with the following frequency bands and maximum
radio-frequency power: Bluetooth 2.4GHz band: 8.53 dBm Bluetooth LE 2.4GHz
band: 1.73 dBm
· It is considered improper use when this product is used for any application
not named in this user manual.
· TCL Corporation bears no responsibility for accidents or damage caused by
improper use of this product.
Caution: The user is cautioned that changes or modifications not expressly
approved by the party responsible for compliance could void the user’s
authority to operate the equipment.
3
2 Welcome
Congratulations on the purchase of your new TCL earphones! After it is set up
and connected, you can enjoy wireless music and phone calls with high quality
sound. You are recommended to read through this user manual which helps you
set up, connect and operate the product easily and properly. For more
information, visit www.tcl.com.
Let’s get started.
What’s in the box
Overview of the truly wireless earphones
2
1
4
3
5
3
2
TW30 Charging case & earbuds
9
3
2
5 pairs of replaceable earcaps
QSG
–
3
1 Charging case 2 Charging case LED indicator 3 Charging case button 4 USB Type-C charging slot 5 Touch control area
USB cable (for charging)
Quick start guide
Safety sheet
Safety sheet
4
3 Charge
Charge the battery
Charging case
Connect the supplied USB charging cable to: · The USB Type-C charging slot on
the charging case and; · The USB AC adapter.
The LED indicator at the front of the charging case is solid amber. It will
becomes to solid green when charging is complete.
Note · After the first time charge, a normal charge takes
approximately 2 hours. · Use fast charge can fully charge your phone faster.
(10 minutes of fast charge is equivalent to one hour of normal charging) · Use
only the supplied USB charging cable for charging to prevent product damage.
Warning Only charge with certified USB adaptor DC 5V capable of 0.5A output
current or more.
Earphones
Place the earphones in the charging case. The earphones will start charging
automatically. The LED indicators will flash 3 times, and finally be solid on.
When charging is complete, the LED indicators will becomes solid green.
You can charge the earphones in the charging case using the USB Type-C cable.
Check the battery status
Charging case
To check the charging case battery level status, press the status button at
the side of the charging case.
X 1
· The LED indicators solid amber in 5 seconds when the charging case battery
power less than 50%.
· The LED indicators solid green in 5 seconds when the charging case battery
power more than 50%.
Earphones
Take out of the earphone you want, and then put it back into the charging
case.
· The LED indicator will flshing amber for 3 times when the earphones battery power less than 50%.
· The LED indicator will flshing green for 3 times when the earphones battery power more than 50%.
You can also connect the earphones to your smartphone via TCL Connect app, you can find the battery level on the app home screen.
Note The location and availability of the battery level indication may vary depending on the operation system of your mobile device. For more information, consult the user manual of your smartphone or Bluetooth device.
5
4 Connect your earphones
Before you can make calls and enjoy music with your earphones, follow the
instructions below to set up and connect your earphones.
Google Fast Pair
(Just for Android phone 6.0 and above with Google Play Service) 1. Make sure
your phone is unlocked and your Bluetooth,
Google Play Services notification, and Location are on. Log in to your Google
account on your phone.
2. Open the charging case. Ensure earbuds and charging case are charged and
keep the case next to your phone.
3. Tap the earbuds pairing notification and follow the onscreen steps.
Nearby now TTaCpLtoMpOaVirEwAiUthDtIhOisSd2e0v0ice
Nearby · now
MOVEAUDIO S600 Tap to pair with this device
connected one. · Make sure your smartphone or device has Bluetooth®
capability and is compatible to the earphones (see ‘Bluetooth® profile’ on
page 3).
90%
90%
90%
Bluetooth Bluetooth
Bluetooth TCL MOVEAUDIO S600
Pairing your earphones via app
1 Download and install the app on your smartphone. Search for “TCL Connect” in
the Google Play store (Android 5.0 and above), or App store (iOS 10.0 and
above). Scan the following QR code.
Manual Pairing
1 Make sure the Bluetooth function of the previous connected device is turned
off. You can also disconnect it from the previous connected device manually.
Place the earphones back to the charging case.
2 Open The charging case. 3 Press and hold the charging case button for 3
seconds
on the side of the charging case. The earphones will enter pairing mode. The
LED
indicator on the charging case will flashing white. 4 Turn on the Bluetooth®
function of your smartphone. 5 Select MOVEAUDIO S600.
You will hear a voice prompt when pairing is successful.
Note · The earphones can save up to 10 different devices you
have connected. If you connect to more than 10 devices, the earliest connected
device is replaced by the last
2 Touch the app icon to enter the TCL Connect app.
3 Touch Agree and continue.
4 Select your device in the list.
5 Touch Pairing to complete. Once the earphones has been successfully paired
with your phone, you will be brought to the application main screen.
6
5 Use your earphones
You can now enjoy wireless music and make your phone calls with your
earphones.
Wear the earphones
Place the earbuds in a forward and down position.
Power your earphones on or off
Reconnect your earphones to your smartphone or Bluetooth® device
1 Turn on your smartphone or Bluetooth® device. 2 Turn on your earphones.
The earphones are reconnected to the last connected smartphone/Bluetooth®
device automatically.
Note · You are recommended to turn on the smartphone/
Bluetooth® device or activate the Bluetooth® feature before turning on the
earphones. Otherwise, you have to reconnect the earphones and
smartphone/Bluetooth® device manually.
· The earphones will turn on automatically when you open the charging case.
· The earphones will turn off automatically when you close the charging case.
TCL MOVEAUDIO S600
· If the earphones fail to connect to any Bluetooth® device within 5 minutes,
the earphones will switch off automatically to save the battery life.
Wearing detection
Your headset has automatic wearing detection function. When you take off the
headphone, the sound will pause. When you put on it again within 15 seconds ,
it will continue to play. You can enable/disable this function on the home
screen of the TCL Connect app. Default is ON.
7
Music control
Music control Play or pause Skip forward Skip backward
Operation (touch control area) Touch once 3 Touch twice 3 Triple touch 3
–
3
Call control
Call control
Operation (touch control area)
Pick up or hang up a call
Touch twice – / 3
Reject an incoming call
Press and hold – / 3 for 2 seconds
–
3
Voice assistant
Phone voice commands enable you to speak to Siri®
or Google AssistantTM on your smartphone using your earphones. For more
information on using Siri® or Google
AssistantTM, consult the user manual of your smartphone or Bluetooth® device.
Call control
Operation (touch control area)
Talk to your Google AssistantTM
Press and hold
–
Stop Google Assistant
Touch once –
Listen to notification Touch twice –
8
ANC control
Your headphones are featured with ANC (Active Noise Cancelation) function that
protects your hearing from unwanted environmental noise using active noise
control. With ANC function activated, you can enjoy free mobile communications
and increase comfort while listening to music. The ANC is on as default.
Long press and hold the 3 for 3 seconds to enter Transparency mode when the
earphones ANC function on.
Long press and hold the 3 for 3 seconds to turn off the ANC function when the
earphones is in Transparency mode.
Long press and hold the 3 for 3 seconds to turn on the ANC function when the
earphones ANC function off.
Noise Cancelling
Low battery prompt
· When battery remains 10%, it will play low battery prompt tone only one
time.
· Before power off, will play low battery prompt tone again, and then play
power off tone.
Reset the earphones
If you have to reset your earphones due to the connection or pairing issues,
see the following steps. 1. Place the earphones in the charging case. Do not
close
the lid.
ANC OFF
Transparency
00:03
mode
You can choose the mode you want on the TCL Connect app home screen if your
earphones have paired with the phone.
Note · If the ANC is on, the headphone will not turn off
automatically in any states. · You are recommended to disable the ANC function
when
it is not needed to save the battery life.
2 Press and hold the button for 10 seconds. When reset completed, the LED
indicator on the charging case will flashing amber for 3 times.
00:10 X3
9
6 Firmware update
You can update the firmware thought the TCL Connect app. Make sure that your
earphones have paired with the phone. 1 Charing your earphones if no enough
power in. (see
‘Charge the battery’ on page 5) 2 Power on the earphones. (see ‘Power your
earphones on
or off’ on page 7) 3 Enter the TCL Connect app, and touch the icon on the
right-up of the home page. 4 Touch Firmware to check the firmware version.
A red dot will appear if a new version existed. 5 Touch Update. Note: The
firmware update only works when the earphones are powered on.
10
7 Notice
Compliance notice
EMF This product complies with all applicable standards and regulations
regarding exposure to electromagnetic fields.
Declaration of conformity
Hereby, TCL Corporation declares that this product is in compliance with the
essential requirements and other relevant provisions of Directive 2014/53/EU.
You can find the Declaration of Conformity on www.tcl.com
Remove the integrated battery
Check your country’s local waste regulations for the proper disposal of
electronic products. To protect the environment, remove and recycle the
headphone battery before disposing of them. For your safety, contact an
authorized service center to remove the battery. If the battery is not
properly removed, it may lead to damage to the battery, and/or cause personal
injury.
Disposal of your old product and battery
Environmental protection and sustainability We have omitted all unnecessary
packaging and make sure it is eco-friendly and sustainable.
Your product is designed and manufactured with high quality materials and
components, which can be recycled and reused. Please observe the local
regulations regarding the disposal of packaging materials, exhausted batteries
and old equipment. For recycling information, please visit www.tcl.com
This symbol on a product means that the product is covered by European
Directive 2012/19/EU.
This symbol means that the product contains a built-in rechargeable battery
covered by European Directive 2013/56/EU which cannot be disposed of with
normal household waste. We strongly advise you to take your product to an
official collection point.
battery
battery
Lithium polymer battery (Charging case: 520mAh; Earphones: 30mAh)
11
8 Notice for US and Canada
Compliance notice for US
This device complies with the FCC rules. Operation is subject to the following
two conditions: 1. This device may not cause harmful interference, and
2. This device must accept any interference received, including interference
that may cause undesired operation.
FCC rules
This equipment has been tested and found to comply with the limits for a Class
B digital device, pursuant to Part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and
on, the user is encouraged to try to correct the interference by one or more
of the following measures: · Reorient or relocate the receiving antenna. ·
Increase the separation between the equipment and
receiver. · Connect the equipment into an outlet on a circuit different
from that to which the receiver is connected. · Consult the dealer or an
experienced radio/TV technician
for help.
FCC Radiation Exposure Statement:
This equipment complies with FCC radiation exposure limits set forth for an
uncontrolled environment. This transmitter must not be co-located or operated
in conjunction with any other antenna or transmitter.
Compliance notice for Canada
This device complies with Industry Canada licenceexempt RSS standard(s).
Operation is subject to the following two conditions: (1) this device may not
cause harmful interference, and (2) this device must accept any interference
received, including interference that may cause undesired operation.
CAN ICES-3(B)/NMB-3(B)
IC Radiation Exposure Statement This equipment complies with Canada radiation
exposure limits set forth for uncontrolled environments. This transmitter must
not be co-located or operating in conjunction with any other antenna or
transmitter. Caution: The user is cautioned that changes or modifications not
expressly approved by the party responsible for compliance could void the
user’s authority to operate the equipment.
12
9 Trademarks
The Bluetooth® word mark and logos are registered trademarks owned by
Bluetooth® SIG, Inc. and any use of such marks by TCL Corporation under
license. Siri® Siri® is a trademark of Apple Inc., registered in the U.S. and
other countries. GoogleTM GoogleTM and the GoogleTM Logo are registered
trademarks of GoogleTM Inc., and Google AssistantTM is a trademark of
GoogleTM, Inc. USB Type-CTM USB Type-CTM is a trademark of USB Implementers
Forum. TCL TCL is a registered trademark of TCL Corporation in the U.S. and
Canada. All other trademarks and trade names are the property of their
respective owners.
13
10 FAQ
I cannot switch on the earphones. · Your earphones do not have enough battery
power.
Charge your earphones (see ‘Charge’ on page 5).
The earphones do not pair with my device. · Make sure you have turned off the
Bluetooth function of all
previously connected Bluetooth devices as the earphones will automatically
connect to previous connected device. · On your smartphone or Bluetooth
device, remove `MOVEAUDIO S600′ from the Bluetooth list. · Follow the steps in
this user manual to pair your earphones. (see ‘Connect your earphones’ on page
6).
Do my earphones support connecting to multiple devices at the same time? · No.
To connect to another device, disconnect the current
device from your earphones, press and hold the button on the charging case for
more than 10 seconds, and search for and connect to your earphones on the
other device.
I cannot find the earphones model name on the pairing list of my Bluetooth®
device to make a first time connection. · Turn off the Bluetooth function of
the Bluetooth device
and turn it on again. · Initiate the Bluetooth device searching function of
your
Bluetooth device again.
I cannot connect the earphones to a new device. · Make sure the Bluetooth
function of the previous paired
device is turned off. · Pair your new device again.
Place the earbuds in the charging case, and leave the case opened. Press and
hold the Function button for 10 seconds until the indicator turns amber and
then flashes white in order for the earbuds to enter Pairing mode, then click
TCL MOVE AUDIO S600 in your smartphone to connect.
The earphones are not connected to my smartphone automatically. · Make sure
the Bluetooth function of your smartphone is
switched on before you switch on the earphones.
The earphones keep on disconnecting. · Your earphones do not have enough
battery power.
Charge your earphones · Make sure the earphones and Bluetooth® device are
within the operation range. Remove any unnecessary Bluetooth® devices. ·
Remove the earphones from the pairing list and pair them with your device
again.
How do I enable or disable the ANC (active noise cancellation) feature? · The
MOVEAUDIO S600 have Noise canceling mode,
Transparency mode, and Off mode. Noise canceling mode is enabled by default. ·
You can switch between the three modes in the following ways. Long press Long
Press the left or right earbud. You will hear a prompt tone when the earbuds
have been switched to a different mode. TCL Connect You can download and
install TCL Connect from Google Play Store or App Store. Add your earbuds to
the device list in TCL Connect, and go to the earbuds details screen. Touch
Noise canceling under Noise control, touch Mode under Noise canceling, and
select your preferred mode.
The noise canceling of the earphones doesn’t work very well, especially when
it is windy Cause · Noise canceling may be disabled. · The size of the ear
tips is not suitable for you or you may
be wearing the earphones incorrectly, resulting in poor air tightness. · The
sound openings such as microphone and speaker openings are blocked by foreign
objects Solution · Long press the touchpad to enable noise canceling. A prompt
tone will be played when you operate the earphones. · Ear sizes vary between
individuals, so the default ear tips may not be a perfect fit for your ears. ·
The earphones come with silicone ear tips in sizes S, M, and L for you to
choose the most comfortable fit. Adjust the position of the earphones to
ensure that they fit well in your ear canals.
Indicator light description ·Refer to the following table for more information
about the status indicators.
14
Indicator light description · Refer to the following table for more information about the status indicators.
User cases
Indicator color
Remark
Factory reset
Flash Amber
Pairing mode
Flash White
Earbuds is in the charging case 1.Open the case 2.Press the button
Stay green for 5s Stay amber for 5s
Earbuds in High battery level ( 50%) Earbuds in Low battery level (< 50%)
Earbuds is in the charging case 1.Take off the earbuds from the case 2.Put the earbuds in to the charging case
Flash green 3 times Flash amber 3 times
Earbuds in High battery level ( 50%) Earbuds in Low battery level (< 50%)
Earbuds is not in the charging case 1.Open the case 2.Press the button
Stay green for 5s Stay amber for 5s
Charging case in High battery level (50%) Charging case in Low battery level (< 50%)
Steady green
Being charged and at full battery level (100%)
Charging the case
Steady amber Flash amber
Being charged (battery level < 100%)
The connection between charging cable and charging case is not stable or have
some errors for charging
15
How to power off my earphones and charging case · You can’t manually power off
the earphones or charging
case. When you’re not using them, place the earphones in the charging case,
and close the case. Your earphones will enter standby mode to save power. It
is recommended that you regularly charge the charging case.
Why does the music play on my smartphone speaker, but not through my
earphones? · Make sure you have already selected on your smartphone
to listen to music through the earphones. For information, consult the user
manual of your smartphone.
The audio quality is poor and crackling noise can be heard. · Make sure the
Bluetooth® device is within the operation
range. Reduce the distance or remove obstacles between your earphones and
Bluetooth® device. · Try to reconnect the earphones. The audio quality is poor
when streaming from the smartphone or audio streaming does not work at all. ·
Make sure your smartphone supports both HFP – Handsfree profile and A2DP –
Advanced audio distribution profile (Bluetooth® stereo supported). · Some game
apps with chatting function force the earphones to enable HFP mode to support
voice communication. In HFP mode, the audio quality is poorer than the A2DP
mode. To avoid this issue, try to quit or restart this game app.
I cannot control music functions on my Bluetooth® device. · Make sure the
Bluetooth® audio source supports
AVRCP- Audio video remote control profile. Some music or video player apps do
not fully support AVRCP. Check other apps to see if the problem still exists.
If so, try to reconnect the earphones.
I can hear sound only from one earphone. · One earphone may be out of battery.
Charge the battery
for both earphones. · Both earphones have disconnected from each other. · Turn
off the earpieces, then turn on and reconnect them. · If the problem persists,
reset the earphones
I found the earphones sound out of sync with the screen when playing videos
and games. · When playing videos or games with a mobile device
connected, the earphones may have a time lag between the video and sound
output.
I cannot hear the other side’s speaking. · For some smartphones, if you pick
up a phone call
through your smartphone, the voice will go through your smartphone. You need
to manually select the Bluetooth earphone on your smartphone, then the voice
will go through the Bluetooth earphones. · Press the right earphone twice to
adjust the volume of your earphones. · Adjust the volume of your connected
Bluetooth® device.
The other side cannot hear my voice. · Check your smartphone to make sure the
voice is going
through the Bluetooth earphones. · Make sure the microphone is not muted. ·
You can take out the right earphone and speak close to
the microphone. It will improve your voice quality in a very noisy
environment.
The charging time and battery life are different between the left and right
earphones. · The charging time may differ between the two earphones
even if they start charging at the same time. · The charging time and
remaining battery may differ
between the two earphones due to different inner components.
I cannot reset the earphones. · To reset the earbuds, place the earbuds inside
the
charging case, keep the case open, and long press the button for more than 10
seconds until the inner indicator turns amber. · The pairing and connection
data of the earbuds will be cleared. The inner indicator will flash amber for
3 times then flash white, indicating that the earbuds have entered Pairing
mode.
I have lost one of the earphones. · Contact our local contact center for
further advice.
How can I dispose of my earphones? · To find the closest electronics recycling
solution to you,
please visit www.tcl.com For further support, visit www.tcl.com
16
WE ARE READY TO HELP contact us first
with any questions
For more details or for help visit:
www.tcl.com
2021© TCL Communication Ltd. All rights reserved. This product has been
manufactured by and is sold under the responsibility of TCL Communication Ltd.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>