MiBOXER High Voltage RGB Dimming LED Drive HF3-P400V210 Instruction Manual

MiBOXER High Voltage RGB Dimming LED Drive HF3-P400V210 Instruction Manual

Features

This item is made by 2.4G wireless transfer technology with low consumption and anti-interference. It supports PWM dimming without any flashing and it’s built-in power driver which is easy to power on device and protect LED chip.There is overload protection.

16 Millions of colors to choose
Mix red, green and blue light to adjust color temperature
Dim brightness/Saturation
2.4G RF wireless transmission technology
Signal transmitting & Modes synchronization
Remote control Control distance 30m
Smartphone App control (2.4GHz gateway is needed)
Support third party voice control (2.4GHz gateway is needed)

Parameters

• Model No.: HF3-P400V210
• Input Voltage: 220-240V~ 50/60Hz
• Input Current: Max 4.1A@230V~
• Output Voltage: 210V
• Output Current: Max 1.9A
• Rated Power: Max 400W
• Efficiency: 94%
• Control Distance: 30m
• Working Temp.: -10~40°C
• Storage Temp.: -40~80°C
• Working Humidity: 20~95%RH, non-condensing
• Overload Protection: limited power

Dimension

Connection Diagram

Link Code / Unlink Code with remote

Link code

1. Switch off LED driver, switch on again after 10 seconds.
2. Short press zone ” ” or ”  ” 3 times on remote within 3 seconds, light blinking 3 times slowly means the linking is done successfully.

Note: The ” ” key for FUT089 remote don’t support to link code.

Unlink code

1. Switch off LED driver, switch on again after 10 seconds.
2. Short press zone ” ” or ” ” 5 times on remote within 3 seconds, light blinking 10 times quickly means the unlinking is done successfully

Compatible with following remote controls
(Purchase separately)

NOTE:
Light will work after linking with remote control; for more details, pls read the remote instruction.

Auto-transmitting & Synchronization

Signal transmitting

LED driver can transmit the signals from the remote control to another one within 30m, as long as there is LED driver within 30m, the remote control distance is unlimited.

Modes synchronization

Different LED driver can work synchronously when they are started at different times, controlled by the same remote, under same dynamic mode and within 30m distance.

Dynamic mode selection

Select dynamic mode table 1:

LED driver is powered off for 10 seconds and then powered on. Press the ” S+ ” button 5 times within 3 seconds, the blue light blink 3 times slowly, selection is done successfully.

Select dynamic mode table 2:

LED driver is powered off for 10 seconds and then powered on.
Press the ” S- ” button 5 times within 3 seconds, the yellow light blink 3 times slowly, selection is done successfully.

Dynamic mode table 1 (default in factory)

Number

| Dynamic Mode| Brightness / Saturation / Speed
---|---|---
1|

Mardi Gras

|

Adjustable

2

| Automatic color change
3|

Sam

4

| Gemstone
5|

Twilight

6

| American
7|

Fat Tuesday

8

| Party
9|

Slow Color Splash

Dynamic mode table 2 (need to switch manually)

Number

| Dynamic Mode| Brightness / Saturation / Speed
---|---|---
1|

Colors gradual change

|

Adjustable

2

| White light Gradual change
3|

RGB gradual change

4

| Seven colors jump to change
5|

Jump to change randomly

6

| Red light gradual change +Flash 3 times
7|

Green light gradual change +Flash 3 times

8

| Blue light gradual change +Flash 3 times
9|

White light gradual change +Flash 3 times

Switch-OFF to change color instruction

Switch OFF (for 3 seconds); Switch-ON again| Switch-OFF ( for over 3 seconds); Switch ON again
---|---
Switch the colors and dynamic modes in turn

1. Static Red
2. Static Green
3. Static Blue
4. Static Yellow
5. Static Purple
6. Static Cya
7. Static Cool White

** 8 to 16 is dynamic mode
(Attention:** default mode is dynamic mode table 1, users can switch to dynamic mode table 2 manually, please review details in No.6)

| Status before switch OFF

Attention

1. Please check whether the input voltage supply is in accordance with the strip light driver.
2. Non-professional user cannot dismantle the strip light driver directly, otherwise, it may and electric shock.
3. The working temperature is -10~40°C; do not use the device to direct sunlight, moist and other high temperature area.
4. Please do not use strip light driver around the mental area and high magnetic field, otherwise, it will badly affect the control distance.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>