GROWER S CHOICE 0713440683190 Digital Lighting Controller User Manual
- June 6, 2024
- GROWER S CHOICE
Table of Contents
MASTER CONTROLLER
MASTER CONTROLLER
INSTRUCTION
The Grower’s Choice Master Controller is a dual-channel module. Each of these
channels being programmable allowing the user to control two separate grow
areas or rooms. This controller uses an LCD touchscreen for easy navigation.
The controller timers operate on a 24-hour clock (Military Time 00:00-23:59).
This controller does not have a setting for AM or PM, this is done in order to
avoid repetition of numbers that could lead to possible confusion.
The Master Controller has two different options for time schedules, the Daily
Cycle and Custom Cycle. The Daily Cycle operates in the continuous repetition
of 24 hours. This cycle is what we consider our timer meaning it will continue
to turn on and off at the programmed time until the time slots are edited. The
Custom Cycle operates in a 48 hour period and begins the second you program
it, after the 48 hours it will reset and you will have to reprogram your time.
Grower’s Choice Master Controller also includes a Sunrise/Sunset setting
allowing you to ramp your lights up and down at the beginning and end of your
programmed times imitating natural light cycles. Safety features include auto-
dimming and auto-shutoff in case of excessive heat that destroys crops such as
an HVAC malfunction.
TECHNICAL SPECIFICATIONS
The Grower’s Choice master controller utilizes a 2-channel system allowing you to control two different cultivation areas, controlling up to 100 units. Both channels provide heat protection shutdown set by the user. This controller has dimming options and can simulate sunrise and sunset cycle from increments of 10-60 minutes. Use the LCD touchscreen to navigate, view, and modify the current settings for each channel easily. Output voltage is 0-11.5v DC.
| Control voltage outputs | 2 Groups, A/B |
|---|---|
| Numbers of ballasts per output | 100 pcs Max |
| Max cable length per group | 100 meters |
| Overheat protection | Yes |
| Sunrise/sunset period | Yes |
| Input voltage | DC5V/2000mA |
| Weight | 1.0kg |
| Warranty | 3 years |
SAM WARNING
keep and mount the master controller in a cool and dry environment away from
dirt, dust, heat, and moisture.
Make sure all RJ and power cords are safely routed away from excessive heat,
moisture, mechanical movement, or anything that may damage cords
Do not attempt to disassemble or repair the master controller. This will void
the controller warranty. ADo not use abrasives, acids, or solvents to clean
the master controller. Use a soft, dry cloth to clean the controller.
Grower’s Choice master Controller and fixtures are specifically designed to
work in conjunction with each other. Using non-Grower’s Choice fixtures with
Grower’s Choice controller may cause malfunctions and may void warranty. For
best results use GC controller and fixtures together. AGrower’s Choice
controllers are designed to work with GC RJ14 data cords. Using other brand or
non-RJ14 data cords could cause malfunctions and may void the warranty
DISPOSAL! THIS PRODUCT CONTAINS A BATTERY AND OTHER MATERIALS, WHICH MUST BE
DISPOSED OF PROPERLY AND IN A LAWFUL WAY, THROUGH AN ELECTRIC RECYCLING
CENTER.
INCLUDED IN THE PACKAGE
POWER SUPPLY AND INITIAL SET-UP
-
Mount the controller onto a secure surface using the screws supplied with the controller.
NOTE: Make sure the controller is mounted level and away from heat sources.
NOTE: The distance between the center of each mounting hole is 12.5cm
-
Connect the power cord into the master controller and power source.
Temp Sensor Information and installation:
1). Connect the temperature sensor plug into the master controller temperature sensor port A.
Hang the sensor at canopy height making sure the sensor and cord are hung and routed away from direct heat sources. Repeat install with port B, if necessary.
Connecting the master controller to light fixtures:
1). Connect one end of the RJ14 cord to the master
controller A port, the other end to the A part of the light fixture.
2). For additional fixtures, connect one end of the RJ14 cord to the “B port” of the last light fixture, and I connect the other cord end to the “A port” of the added fixture.
Touch Dimming” to access power level settings
Touch Auto Pilot ” to access Daily or Custom Cycle ” options and
program timer settings.
Touch “ Auto Pilot ” to access “Daily or Custom Cycle” options and program
timer settings.
Touch “ Environment” for access to emergency dim and shut-off options that
protect the crop from excessive heat in the event the environment exceeds the
selected temp range.
Touch “System” for access to general settings and system options
Touch to select Group A or Group B to adjust or view settings
Touch Dimming Level” to adjust dim settings from 50%-115% with HID and
15%-100% with LEDs
To activate the OFF, MANUAL ON , or AUTOPILOT touch the desired one
Touch “ Fixture Type to select fixture type and power levels.
Touch and select fixture type or select “ Custom if the wattage is not
shown.
Touch “ Dimming Range Setup to program min. and max. Power levels
Touch “ Minimum ” or “ Maximum ” to set dimming range.
Once the range is selected press Confirm to save settings
NOTE : Minimum settings for ID must be at 50% or higher for lamps to
ignite and Minimum setting for LED 15% or higher.
Of” shuts off all connected fixtures
Manual On Overrides set timers/schedules
AutoPilot Enable turns on the autopilot which allows the controller to
follow time schedules. Clicking it will also bring up the Autopilot settings
Touch and choose “ Daily Cycle to run dimmer in conjunction with the clock
Touch and choose “ Custom Cycle ” to select the number of hours the clock
fixture will be on or off
Touch “ On ” and “ OH ” tee settings to adjust Auto-Pilot timers. Be
aware of cycle settings when programming timers
NOTE: Custom Cycle example setting 8:00 and 18:00 would mean the light is
set for 8 hours on and 18 hours off and NOT on at 8:00 and off 18:00 hours.
Touch the minute value to adjust “Sunrise/Sunset” settings from 01-60
minutes
Touch to Activate or Disable the Sunrise/Sunset settings
NOTE: Sunset setting will dim lights before scheduled off time and lights
will be off by scheduled time.
Touch Auto.Dim to set the temperature at which the controller will dim the
lights in case of excessive heat
Touch “ Shut-Down ” to set the temperature at which the controller will
turn off lights in case excessive heat continues
Touch for access to “ Time Settings “.
Touch for access to Fahrenheit or Celsius temperature selection.
Touch for access to “ Screen Lock “.
Touch for access to “ Warning Display “.
for access to “ Language ” choice.
for access to “ General ” settings.
Touch “Active” or “Deactivate” to turn Warning Display , On
Off.
Touch to enter “Warning” level temperature value.
Touch to enter “Urgent” level temperature value.
NOTE: In “Warning Display mode”, the screen will display in yellow for
“warnings” and will turn red for “urgent”. If the environment is not
corrected, the protective measures are activated and the lights will shut off.
When the environment is managed within the chosen settings of safe operation
the screen with reset back to a green display.
Touch “ Screen Auto-Lock ” to activate or deactivate screen lock and enter
time before screen locks using the “min” option.
Touch to select the slide lock to be on or off.
NOTE: Minimum settings for HID must be at 50% or higher for lamps to
ignite and Minimum setting for LED 10% or higher.
Toll Free Number
: 909-972-8419
E-mail : info@growersc.com
Website : www.growersc.com
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>