SC T HE02EIX HDMI Over HDBaseT Extender User Manual

: June 6, 2024
: SC T

Table of Contents

Introduction
Features
Installation view
Trouble Shooting
Specification
Read User Manual Online (PDF format)
Download This Manual (PDF format)

HDMI over HDBaseT Extender
User Manual

Model : HE02EIX
4K 60Hz 4:4:4 HDMI & IR/R232 CAT5e Extender 70M

Introduction

HE02EIX is a 4K HDMI over HDBaseT™ extender that can use an Ethernet cable to send uncompressed HDMI, bi-directional IR, and RS232 signals with resolution up to 4K@60Hz 4:4:4 and transmission distance up to 70M. Its TX unit has a built-in local loop-out port that can connect with an extra HDMI display and its RX unit has dual HDMI outputs for signal distribution.

Features

Resolution up to 4K@60hz 4:4:4.
Signal extension up to 70M over CAT5e or greater cable.
Built-in local loop out for an extra HDMI display at the TX side.
Built-in dual HDMI outputs at RX.
Supports bi-directional IR, RS232 transmission.
Supports CEC, and EDID pass through.

Installation view

Cable
Link cable recommends using high-quality CAT5e, CAT6, CAT6a, CAT7 UTP / STP, or FTP cable. Poor quality cable or network connection or improper construction will cause unstable connection, video or sound disruptions, picture noise appears.

HDBaseT Distance Chart by Different Cable

Cable Type	Range	Supported Video
CAT5e / CAT6	60m	Up to 1080p 60Hz 12bit
CAT6e / CAT7	70m
CAT5e / CAT6	35m	Up to 4096×2160@60Hz 4:4:4
CAT6a / CAT7	40m

If connection through the wall socket, the cable length must be less than 5 meters between HDMI extender and the wall jack, as below drawing

RJ45 Define
Video Link (TIA/EIA-568-B)

1. Orange-white	DATA0 +
2. Orange	DATA0 –
3. Green-white	DATA1 +
4. Blue	DATA2 +
5. Blue-white	DATA2 –
6. Green	DATA1 –
7. Brown-white	DATA3 +
8. Brown	DATA3 –

Panel View

LED Indication

Color

|

Status

|

HE02EIXT

|

HE02EIXR

---|---|---|---

GREEN

|

LINK

|

ON: HDBaseT Linking

BLUE

|

VIDEO

|

ON: Input signal 4K@60Hz 4:4:4

RED

|

FW UP

|

ON: Firmware Update

Color

|

Status

|

HE02EIXT

|

HE02EIXR

---|---|---|---

GREEN

|

ON

|

ON: Power normal

BLUE

|

IR RX

|

ON: Receiving IR signal

RED

|

IR TX

|

ON: Sending IR signal

Firmware updated Switch

1. RS232	ON: Firmware Update, OFF: RS232 Extender
2. Reserve	Must Keep Off
3. Low Power Mode	ON: Turn off power saving mode, OFF: Turn on power-saving

mode
4. Reserve| Must Keep Off

RS232 Define

DB9 (F)/3.5mm STEREO PHONE JACK

RS232	3.5 mm Phone Jack
Footprint	Define
Pin 2	TX
Pin 3	RX
Pin 5	GND

DB9 (M)/3.5mm STEREO PHONE JACK

RS232	3.5 mm Phone Jack
Footprint	Define
Pin 2	RX
Pin 3	TX
Pin 5	GND

Package Include

HE02EIXT	x 1
HE02EIXR	x 1
DC 5V 2A Adapter	x 2
IR Receiver Cable	x 1
IR Emitter Cable	x 1
DB9 (M)/3.5mm STEREO PHONE JACK	x 1
DB9 (F)/3.5mm STEREO PHONE JACK	x 1
Mounting Screw pack	x 2

Trouble Shooting

The wiring must be away from any equipment with an electromagnetic wave, i.e.: mobile phone, microwave, radio equipment, fluorescent lamp, high voltage power lines.
Under HDMI 2.0 mode, must use Premium certified HDMI cable.
EDID pass-through for HE02EXT transmitter input and HE02EXR receiver output 1 only
CEC works for HE02EXT transmitter input and HE02EXR receiver output 1 only.
Under HDCP 2.2 mode: anyone who monitors HDCP authorization fail will cause no video status, other connecting monitors will be also failed. Then monitor testing must be done one by one to find which monitor HDCP failed.
This device DBase port is not a general Ethernet signal; do not connect with Network devices to avoid damage.
IR transmitters do not put near from receiver to avoid mutual interference.