SC T DKM01 DVI Repeater User Manual
- June 6, 2024
- SC T
Table of Contents
SC T DKM01 DVI Repeater
Introduction
DKM01 is a DVI extender that can not only carry DVI signal but USB, analog audio, RS232 ones using a cost-effective Ethernet cable with transmission distance up to 140M. You can easily control a PC where is far away from you while having an additional DVI monitor along side using the loop-out port at TX unit. It is an ideal solution for industrial, hospital, and education fields.
Features
- Resolution up to 1080p or 1920×1200@60Hz.
- Signal extension up to 140M over CAT6, 120M over CAT5e.
- Built in DVI loop-out port at TX unit..
Optional Model: SR01X Gigabit Ethernet Repeater
- Extend TCP/IP signal for extra 120meters.
- Chainable with multiple SR01X for long-distance transmission.
- Plug and play for easy installation.
Installation view
Work with SR01X Gigabit Ethernet repeater
Panel View
Interface/ Function
- Power LED To Indicate the status of power
- LINK LED To Indicate the status of data transmission
- Rotary Switch To set up the grouping function
- DIP Switch To set up the grouping, EDID, RS232 functions
- EDID To set up EDID function
- RS232 To connect an RS232 device
- LINE OUT To connect a 3.5mm jack for a speaker
- LINE IN To connect a 3.5mm jack for a microphone
- USB HOST To connect a USB-B cable
- RJ45 Connector To connect a DKM01T/R
- DVI IN To connect a DVI source
- DVI LOOP OUT To connect a DVI display
- Power Jack To connect a DC5V 2A power adapter
- MENU To check the status of MAC, IP, Baud Rate and EDID
- SELECT To set up Baud Rate
- USB To connect 4 ports of USB devices (ie. Keyboard, mouse)
- DVI OUT To connect a DVI display
- MIC IN To connect a 3.5mm jack for Microphone
Description
-
LED Indication Status:
Power On| Link On
---|---
Green ON| Blue On -
RJ45 Indication Status:****
Link On| Data Transferring
---|---
Green ON| Yellow On -
RJ45 Pinout****
Pin| Color| Data
---|---|---
1| Orange-white| DATA0 +
2| Orange| DATA0 –
3| Green-white| DATA1 +
4| Blue| DATA2 +
5| Blue-white| DATA2 –
6| Green| DATA1 –
7| Brown-white| DATA3 +
8| Brown| DATA3 – -
RS232 Define
DB9 (F)/3.5mm STEREO PHONE JACK
RS232 | 3.5 mm Phone Jack | RS232 | 3.5 mm Phone Jack | |
---|---|---|---|---|
Footprint | Define | Footprint | Define | |
Pin 2 | TX | Pin 1 | RX | |
Pin 3 | RX | Pin 2 | TX | |
Pin 5 | GND | Pin 3 | GND |
Enable RS232 function
DKM01T
SWITCH| RS232 / Settings
SW2| RS232 On
(Default)
| OFF ↑
SW3| OFF ↑
DKM01R
SWITCH| RS232 / Settings
SW2| RS232 On
(Default)
| OFF ↑
- Press “Menu” button of Rx (DKM01R) to select “Baud Rate”
- Press “Select” button of Rx (DKM01R) to choose Baud Rate parameter 3.2.4 Press “Menu” button again to confirm the parameter
- Supported Baud rates: 115200, 38400, 19200, 14400, 9600, 4800, 2400, 1200
- Grouping Set up the switch of Tx and Rx (DKM01T/R) to choose a group.
SWITCH| Group / Settings
---|---
SW1|
Group 0
| OFF ↑|
Group 1
| ON ↓
SW2| OFF ↑| OFF ↑
- Set up the rotary switch (the switch of Tx and Rx should be at the same position)
- Remove the power jack and plug it in again.
- EDID Copy Based on your requirement, you can set up EDID from either TX or RX.
- Remove all the DVI cables.
-
- Set up the DIP switch of Tx.
SWITCH| EDID Mode / Settings
---|---
SW4| 1080p
- Set up the DIP switch of Tx.
(Default)
| OFF ↑| Copy
the resolution from Rx side
| ON ↓| Copy
the resolution from TX loop out side
| OFF ↑
SW5| OFF ↑| OFF ↑| ON ↓
Press EDID Button of the DKM01T to confirm the change.
* You can also set up EDID from RX (DKM01R) to copy the resolution of connected
* monitor from RX side as below.
Step 1 | Press “MENU” button from RX to select EDID. |
---|---|
Step 2 | Press “Select” button from RX to confirm the change. |
Trouble Shooting
- We strongly recommend using high-quality CAT5e, CAT6 UTP/STP/FTP cable. Improper installation may cause unstable connection, and video & audio interruption.
- DKM01 transmission data rate up to 850Mbps Max.
- Do not connect general LAN to avoid data transmission slow down other LAN devices. 。
- Analog audio of Rx (MIC IN) is mono sound for microphone use only, not stereo audio (Line in)
- Every port of USB at receiver side has max output power at 500mA, and 4 ports of USB can
Package Include
No. | Item | Amount |
---|---|---|
1 | DKM01T (Tx) | 1 |
2 | DKM01R (Rx) | 1 |
3 | USB A/B cable | 1 |
4 | DB9 male to 3.5mm phone jack cable | 1 |
5 | DB9 female to 3.5mm phone jack cable | 1 |
6 | DC 5V 2A power adapter | 2 |
7 | Screw | 8 |
8 | Screw plug | 8 |
9 | Rubber gasket | 2 |
Specification
ITEM NO. | DKM01T | DKM01R |
---|
Support
Compliance| HDCP 1.4, USB 2.0, USB 1.1, USB 1.0
Max. Video Resolution| 1920 x 1200@60 Hz
Max. Transmission Distance| 140M over CAT6 or Greater
Video Bandwidth| 10.2 Gbps
Ports & Interfaces
Video Input| 1 x DVI-D (Digital Only)| 1 x RJ45
Video Output| 1 x RJ45| 1 x DVI-D (Digital Only)
Video Loop-out| 1 x DVI-D (Digital Only)|
Analog Audio Input| 1 x (3.5mm) Stereo Phone Jack (Line In)| 1 x (3.5mm)
Stereo Phone Jack (Mic In)
Analog Audio Output| 1 x 3.5mm Stereo Phone Jack| 1 x 3.5mm Stereo Phone Jack
USB Interface| 1 x USB 2.0 Type B| 4 x USB Type A
RS232 Interface| 1 x (3.5mm) Phone Jack| 1 x (3.5mm) Phone Jack
Power
Power Supply| DC 5V 2A| DC 5V 2A
Power Consumption| 1000mA| 400mA
Ambient Temperature
Operation| -20 to 60℃
Storage| -20 to 85℃
Humidity| Up to 95%
Physical Characteristics
Dimensions| 125 x 140 x 30mm| 125 x 140 x 30mm
Weight| 400g| 385g
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>