i-tec U3HUBMETAL10 USB 3.0 Metal Charging Hub 10 Port User Guide
- June 6, 2024
- i-tec
Table of Contents
USB 3.0 METAL
CHARGING HUB 10 PORT
User guide
EN Please read the entire instruction manual carefully. A detailed manual is
available on our website www. i-tec.CZ/en/in the
tab „Manuals, drivers“. In case of any issues, please contact our
technical support at:
support@itecproduct.com
INTRODUCTION
itec USB 3.0 Metal Charging HUB will immediately catch your attention thanks to its elegant metallic design. It is an ideal companion for everybody who does not have enough USB ports in his/her notebook, ultrabook, or PC and who has to constantly connect and disconnect his/her favorite USB equipment such as flash disks, mobile phones, tablets, digital cameras, MP3 players, printers, etc. This HUB offers 10 USB 3.0 ports with the Plug & Play function and standard USB charging – the HUB will automatically detect connected equipment for USB charging. One of the advantages is that thanks to their placement you have enough space even for connection of large pieces of equipment. The USB 3.0 interface is important mainly for data transfers from USB 3.0 memory cards and flash disks which will use its high transfer speed most. The advantage is included an external power adapter which you can use for backing up data on external hard drives or for connecting high power consumption devices which are powered directly from the USB port. This HUB does not require the installation of drivers. You will just connect it by the USB cable to your computer and immediately you can start using it. This HUB has a built-in overcurrent protection of your computer in case of a short connection on the peripheries. The interface is compatible with USB 2.0 / 1.1. Thanks to its compact dimensions and low weight it is an ideal companion to your notebook when traveling.
INSTALLATION IN WINDOWS 7 / 8 / 8.1 / 10, MACOS X AND HIGHER
The HUB has been installed automatically, no need to install drivers. Connect
the connector of the power adaptor to the HUB and connect the power adaptor to
a socket outlet
with 230V. Then plug the HUB via USB cable into an available USB port (USB
3.0, 2.0, or 1.1 standards) of your notebook / PC and follow the on-screen
instructions. The
HUB will be installed and displayed in Device
DESCRIPTION
- Input for connecting the power adaptor
- 1x input USB 3.0 port type A for connecting to a notebook / PC
- 10x output USB 3.0 ports for connecting USB equipment
- LED diode – the diode is ON when the HUB is connected to the power adaptor or to a USB port of a notebook / PC
CHARGING
You can use an external power adapter if you connect the printer, scanner, or
other high-power consumption devices to USB ports in HUB (a power adapter is
included). Respect the basic rules while using this power adapter (for ex. do
not let in reach of children, if the adapter is in 230 V circuit, do not put
it into the water, and so on).
CHARGING
The HUB supports charging of the connected USB mobile equipment such as
smartphones (including iPhone and Samsung phones), ebook readers, multimedia
players, GPS navigators, and tablets (e.g., Asus, Toshiba, GoClever,
Prestigio, Emgeton, Sensor). The HUB does not support the charging of iPad and
Samsung tablets which require special identification circuits. Using the
original cable connect the equipment to be charged to the USB port of the HUB.
At the same time, the power adaptor needs to be connected to the HUB as well.
SYSTEM REQUIREMENTS
Hardware requirements
Notebook / PC with one available USB port
Operating system
Windows 7 / 8 / 8.1 / 10 32/64bit, macOS X 10.x or higher
SPECIFICATION
- 10x USB 3.0 port for connecting USB equipment
- 1x USB 3.0 port for connecting the HUB to a notebook / PC
- Transfer rate up to 5 Gbps
- USB charging detection mechanism for mobile devices
- Plug & Play function
- Overload and overcurrent protection
- LED diode
- Storage temperature -10~85 °C
- Working temperature 0-40 °C
- Power adapter: input AC 100-240 V, 50-60 Hz, 1.5 A; output DC 12 V, 4 AQuick Start / USB 3.0 Metal Charging HUB 10 Port
PACKAGE CONTENTS
- itec USB 3.0 Metal Charging HUB 10 Port
- USB 3.0 cable (90 cm)
- Power adapter (DC cable 150 cm + AC cord 120 cm)
- User Guide
SAFETY INSTRUCTIONS
-
Do not expose to extreme temperatures and air humidity.
-
Use the device on flat surfaces – you will prevent it from slipping and falling to the ground.
-
Save the user manual for possible use later.
In cooperation with the service department: -
Check functionality after falling to water or to the ground.
-
Check functionality when the cover is broken.
-
Send the device back if it does not work in accordance with the user manual.
External power supply exclusively for use with U3HUBMETAL10.
FAQ
available on our website www.i-tec.CZ/en/ on the
„FAQ“ tab of this product.
EUROPEAN UNION ONLY
NOTE: MARKING IS IN COMPLIANCE WITH THE EU WEEE DIRECTIVE
This equipment is marked with the above recycling symbol. It means that at the
end of the life of the equipment you must dispose of it separately at an
appropriate collection point and not place it in the normal domestic unsorted
waste stream. This will benefit the environment for all. (European Union only)
Amendment to user manual providing all necessary information required by
COMMISSION REGULATION (EU) 2019/1782.
(This product meets all the requirements laid down by the above regulation).
FCC COMPLIANCE STATEMENT
This equipment has been tested and found to comply with the limits of a Class
B digital device pursuant to Part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation.www.i-tec.cz/en
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>