ANKER A1720 521 Portable Power Station User Manual

For FAQs and more information, please visit:anker.com/support

Anker 521 Portable Power Station
(PowerHouse 256Wh)
USER MANUAL

Overview

Recharging

• To prevent over-discharge, your portable power station is shipped with its battery deactivated and needs to be charged before using for the first time.
• When your portable power station only has 1% battery remaining, the Remaining Battery indicators will flicker to remind you to recharge the product.

Charging

1. The USB-A and USB-C ports support plug and charge. When devices are plugged in, they will start charging automatically; when devices are unplugged, they will turn off automatically.
2. The car socket and AC output port do not support plug and charge. Use the corresponding on/off buttons to turn them on before charging.
3. To avoid draining the battery, we recommend keeping Power Saving Mode turned on except when you are charging low-powered devices like CPAP machines and cameras.

LCD Screen Guide

| Power Saving Mode
---|---
| High-Temperature Alert
• When this icon shows, stop using the product and leave it to cool down until the icon disappears.
| Low-Temperature Alert
• When this icon shows, stop using the product until the icon disappears.
| USB-C Input/Output Port
| USB-A Output
| Car Charging
| AC Charging and Local Current Frequency
Press the AC output port on/off button for 2 seconds to switch the frequency
| Remaining Battery
| Remaining Battery in Hours
| Current Input Power
| Current Output Power

Flashlight Mode
Press the button once to turn on the ambient light.

Hold the button for 2 seconds to turn on SOS mode.

FAQ
Q1: What’s the max power output of the AC port?
200W, and if you use the AC port for devices greater than 200W, the product will automatically turn off.
Q2: Can I recharge the product while charging connected devices?
Yes.
Q3: Can this product power a CPAP?
Yes, but do not forget to turn off the Power Saving Mode first.
Q4: Will this product lose power automatically if not powered off?
Yes, when the car socket or AC control button is turned on, even if no devices are being charged, there will still be a certain amount of no-load power consumption. To avoid draining the battery, we recommend keeping Power Saving
Mode turned on except when you are charging low-powered devices like CPAP machines and cameras.
Q5: What kind of solar charger can charge this product?
Any 12V-28V solar charger with a DC 8mm（DC 7909）male connector.

Specifications

Attention
Not permitted on aircraft.

IMPORTANT SAFETY INSTRUCTIONS

WARNING – When using this product, basic precautions should always be followed, including the following: Read all the instructions before using the product.

• To reduce the risk of injury, close supervision is necessary when the product is used near children.

•  Do not put fingers or hands into the product.

• Do not expose the product to rain or snow.

• Use of a power supply or charger not recommended or sold by the product manufacturer may result in a risk of fire or injury to persons.
  To reduce the risk of damage to the electric plug and cord, pull the plug rather than the cord when disconnecting the product.

• Do not use the product in excess of its output rating. Overload outputs above rating may result in a risk of fire or injury to persons.

• Do not use the product that is damaged or modified. Damaged or modified batteries may exhibit unpredictable behavior resulting in fire, explosion or risk of injury. Do not operate the product with a damaged cord or plug, or a damaged output cable.

• Do not disassemble the product. Take it to a qualified service person when service or repair is required. Incorrect reassembly may result in a risk of fire or electric shock.

• Do not expose to fire or high temperatures. Exposure to fire or temperatures above 130°C may cause an explosion. To reduce the risk of electric shock, unplug the power pack from the outlet before attempting any instructed servicing.

• Have servicing performed by a qualified repair person using only identical replacement parts. This will ensure that the safety of the product is maintained.

When charging a device, the product may feel warm, this is a normal operating condition and should not because for concern.
When charging the internal battery, work in a well-ventilated area and do not restrict ventilation in any way.
• Do not clean the product with harmful chemicals or detergents.
• Misuse, dropping or excessive force may cause product damage.
• When disposing of secondary cells or batteries, keep cells or batteries of different electrochemical systems separate from each other.

Storage and Maintenance instructions
1. Please use or store the product between 32°F-104°F. Avoid exposing the product to rain or using the product in a humid environment.
2. To preserve battery lifespan, please discharge the battery to 30% and recharge it to 60% every three months.
3. For safety, please do not store the product in an environment with a temperature higher than 113°F or lower than 14°F for an extended period of time.
4. Please keep the product laid flat during use when charging, and during storage.

FCC Statement
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful nterference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Warning: Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to  adio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
(1) Reorient or relocate the receiving antenna.
(2) Increase the separation between the equipment and receiver.
(3) Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
(4) Consult the dealer or an experienced radio / TV technician for help.
The following importer is the responsible party.
Company Name: Fantasia Trading LLC
Address: 5350 Ontario Mills Pkwy, Suite 100, Ontario, CA 91764
Telephone: +1-800-988-7973
IC Statement
This device complies with Industry Canada license-ICES-003. Operation is subject to the following two conditions: (1) This device may not cause interference, and (2) This device must accept any interference, including interference that may cause undesired operation of the device.   This digital apparatus complies with CAN ICES-3(B)/NMB-3(B).
Declaration of Conformity
Hereby, Anker Innovations Limited declares that the product type A1720 is in compliance with Directives 2014/35/ EU & 2014/30/EU & 2011/65/EU. The full text of the EU declaration of conformity is available at the following internet address: https://www.anker.com
GB Declaration of Conformity
Hereby, Anker Innovations Limited declares that the product type A1720 is in compliance with Electrical Equipment (Safety) Regulations 2016 & Electromagnetic Compatibility Regulations 2016 & The Restriction of the Use of Certain Hazardous Substances in Electrical and Electronic Equipment Regulations 2012. The full text of the GB declaration of conformity is available at the following internet address: https://www.anker.com
Anker Innovations Limited
Room 1318-19,
Hollywood Plaza,
610 Nathan Road,
Mongkok, Kowloon,
HongKong
The following importer is the responsible party（contract for EU and UK matters）
Anker Innovations Deutschland GmbH
Georg-Muche-Strasse 3, 80807 Munich, Germany
Anker Technology (UK) Ltd
Suite B, Fairgate House,
205 Kings Road,
Tyseley, Birmingham,
B11 2AA, United Kingdom

Customer Service

| 24-Month Limited Warranty
---|---
| Lifetime Technical Support
| support@anker.com
support.mea@anker.com (For Middle East and Africa Only)
| (US) +1 (800)988 7973 Mon-Fri 6:15 – 17:00 (PT)
(UK) +44 (0) 1604 936200 Mon-Fri 6:00-17:00; Sat-Sun 6:00-14:00
(DE) +49 (0) 69 9579 7960 Mo-Fr 6:00 – 11:00
(Middle East & Africa) +971 42463266 Sun-Thu 9:00 – 17:30
(UAE) +971 8000320817 Sun-Thu 9:00 – 17:30
(KSA) +966 8008500030 Sun-Thu 8:00 – 16:30
(Kuwait) +965 22069086 Sun-Thu 8:00 – 16:30
(Egypt) +20 8000000826 Sun-Thu 7:00 – 15:30
(AU) +61 3 8331 4800 Mon-Fri 8:30 – 17:00 (AEST)
(TR) +90 0850 460 14 14 Mon-Fri 9:00 – 18:00
(RU) +8 (800) 511-86-23 Mon-Fri 9:00 – 18:00 (MSK)
| @anker_ocial
@anker_jp
---|---
| @Anker Deutschland
@Anker Japan
@Anker
| @AnkerOcial
@Anker_JP

Product Number: A1720 51005003126 V03

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>