ANKER 531 Solar Panel User Manual
- October 27, 2023
- Anker
Table of Contents
ANKER 531 Solar Panel
Using Your Product
- Unfold 531 Solar Panel and its stand. For maximum charge, adjust the solar panel up to 3 angles and align it directly under the sun.
- Charge your portable power station using the XT-60 port.
Note
- 531 Solar Panel cannot store electricity. You will need a portable power station to store power.
- 531 Solar Panel is compatible with portable power stations with the 11- 60V XT-60 port.
- Charging efficiency is subject to sunlight intensity.
- Keep your portable power station away from direct sunlight. Excessive heat may cause damage.
- 200W refers to the power of the solar panel, which is not equal to the actual power of the output ports. There will be some power loss when solar energy is transferred into electrical energy, so the actual power of the output ports will be less than the power of the solar panel.
Specifications
| Peak Power | 200W |
|---|---|
| Rated Voltage | 48V |
| Rated Current | 4.17A |
| Dimension (Folded) | 22.44 × 23.70 × 2.36 in / 570 × 602 × 60 mm |
| Dimension (Unfolded) | 23.70 × 83.85 × 0.78 in / 602 × 2130 × 20 mm |
| Weight | 20.34 lb / 9.23 kg |
Important Safety Instructions
- Avoid dropping.
- Do not disassemble.
- For the safest and fastest charge, use original or certified cables.
- Open flame sources, such as candles, must not be placed on this product.
- Only use a dry cloth or brush to clean this product.
Notice
FCC Statement
This device complies with Part 15 of the FCC Rules. Operation is subject to
the following two conditions:
- This device may not cause harmful interference, and
- This device must accept any interference received, including interference that may cause undesired operation.
Warning : Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
Note : This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio / TV technician for help. The following importer is the responsible party.
Company N a me: Fantasia Trading LLC
Address: 5350 Ontario Mills Pkwy, Suite 100, Ontario, CA 91764 Telephone:
+1-800-988-7973
IC Statement
This device complies with Industry Canada license-ICES-003. Operation is
subject to the following two conditions:
- This device may not cause interference, and
- This device must accept any interference, including interference that may cause undesired operation of the device.
This digital apparatus complies with CAN ICES-003(B) / NMB-003(B).
Declaration of Conformity
Hereby, Anker Innovations Limited declares that the product type A2432 is in
compliance with Directives 2014/35/EU & 2014/30/EU & 2011/65/EU. The full text
of the EU declaration of conformity is available at the following internet
address:
https://www.anker.com.
Declaration of Conformity
Hereby, Anker Innovations Limited declares that the product type A2432 is in
compliance with Electrical Equipment (Safety) Regulations 2016
& Electromagnetic Compatibility Regulations 2016 & The Restriction of the Use
of Certain Hazardous Substances in Electrical and Electronic Equipment
Regulations 2012. The full text of the GB declaration of conformity is
available at the following internet address:
https://www.anker.com.
Anker Innovations Limited
Room 1318-19, Hollywood Plaza, 610 Nathan Road, Mongkok, Kowloon, HongKong
The following importer is the responsible party (contract for EU and UK
matters)
Anker Innovations Deutschland GmbH
Georg-Muche-Strasse 3, 80807 Munich, Germany
Anker Technology (UK) Limited, GNR8, 49 Clarendon Road, Watford,
Hertfordshire, WD17 1HP, United Kingdom