DOMUS LINE IR WI-XD Wireless Back Door Sensor Instruction Manual

LIGHT STYLE

DOMUS LINE Srl
Via Maestri del Lavoro, 1
33080 PORTIA PN Italy
phone;0039 0434 595911
fax;0039 0434 923345
e-mail;info@domusline.com
website;www.domusline.com
INSTALLATION MANUAL

| Protection class III device.
---|---
| The product must be disposed of separately from urban waste, delivering it to the collection centers established by the prevailing standard. The adequate sorted waste collection contributes to preventing negative effects on the environment and health and favors reuse and/or recycling materials. Incorrect disposal of the product implies the application of the administrative sanctions envisaged by the prevailing regulation.
| The device is only for indoor installation.

Remote radio emitter for lighting control Model
IR WI-XD
IC: 26690-IRWIN
FCC ID: 2AX76-IR-WI

X-Driver set up an example

X-Driver TW set up an example INSTALLATION MANUAL

TECHNICAL DATA

– Maximum operating distance 8 metres.
– Battery mod. CR2450 (3V) lithium (Fig.1).
INSTALLATION:
Fix the bracket (A) in the required position using the screws (B) supplied in the pack (Fig.2)
Check the operating distance according to the indications given in the table in Fig.3
CAUTION: The sensor must not be installed near electromagnetic or heat sources or exposed to direct sunlight.
A maximum of 7 IR WI-XD sensors can be applied to a single X-Driver
COUPLING WITH STATIC LIGHT X-DRIVER WITH MODULE CM2-XD (Fig.4):
– Press the X-Driver button (C) until the blue signaling LED comes on and then press the IR WI-XD (D) button until the signaling LED (E) remains steady, then briefly press the button (D) again until the signaling LED (E) flashes.
COUPLING WITH DYNAMIC TW LIGHT X-DRIVER WITH MODULE CM2-XDTW (Fig.5):
– Press the X-Driver button (C) until the blue signaling LED comes on and then press the IR WI-XD (D) button until the signaling LED (E) remains steady, then briefly press the button (D) again twice until the signaling LED flashes twice.
LIMIT SWITCH OPERATION x TW STATIC AND DYNAMIC LIGHT:
– Limit switch operation, when the unit door covers the sensor (F) the luminaires connected to the X-DRIVER switch off, and vice versa when opening the door they switch on.
To change the operation from LIMIT SWITCH to DIMMER SWITCH briefly press the button (D).
DIMMER SWITCH OPERATION x STATIC LIGHT:
– ON-OFF function: The luminaires connected to X-DRIVER are switched on and off by briefly moving the hand in front of the sensor (F).
– DIMMER and LEVEL MEMORY functions: Keeping the hand steady in front of the sensor (F) it is possible to adjust the brightness of the luminaires.
The selected brightness will be stored until the next reset (LEVEL MEMORY).
To change the operation from DIMMER SWITCH to LIMIT SWITCH briefly press the button (D).
COLOUR CHANGE OPERATION x TW DYNAMIC LIGHT:
The luminaires are switched on and off by briefly moving the hand in front of the sensor (F).
Keeping the hand steady in front of the sensor (F) it is possible to vary the colour hue of the luminaire, the selected colour will be stored until it is changed again (Color Memory).
To change the operation from DIMMER SWITCH to LIMIT SWITCH briefly press the button (D).

BATTERY-POWERED DEVICES:
These precautions are valid for all products equipped with disposable or rechargeable batteries. Improper battery use may cause the batteries to lose liquid, overheat or explode. The battery liquid is corrosive, may be toxic, cause burns to the eyes and skin, and is harmful if swallowed.
To reduce the risk of injury:
– Keep batteries out of reach of children.
– Do not heat, open or tamper with the batteries or dispose of them by throwing them in the fire.
– Avoid contact between metal items and the terminals of the batteries in the device, as this could cause them to overheat and cause burns.
– Remove the batteries when flat and before storing the device for long periods.
Always remove the old batteries when flat or with a low charge, and recycle them or dispose of them in conformity with the laws in force.
– In the event of liquid leakage, remove the battery carefully, preventing the liquid from coming into contact with the skin or clothing. If any liquid leaking form the batteries comes into contact with the skin or clothing, rinse the exposed parts immediately with water.
Use only batteries of the appropriate type and size.
Suffocation hazard:
These devices contain small components which could constitute a suffocation hazard for children. Keep these components out of reach of children.
WARRANTY
The warranty’s general terms and conditions for this device are available at www.domusline.com
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance of 20cm between the radiator & your body.
FCC warning:
Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
Note : This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
-Reorient or relocate the receiving antenna.
-Increase the separation between the equipment and receiver.
-Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
-Consult the dealer or an experienced radio/TV technician for help.
IC warning
This device complies with Industry Canada licence-exempt RSS standard(s).
Operation is subject to the following two conditions: (1) This device may not cause interference, and (2) This device must accept any interference, including interference that may cause undesired operation of the device.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>