kogan CT3TRTKEJWA 3 In 1 Tyre Repair Tool Kit with Electric Jack and Wrench User Guide

: June 6, 2024
: Kogan

Table of Contents

SAFETY & WARNINGS
COMPONENTS
OVERVIEW
OPERATION
SPECIFICATIONS
TROUBLESHOOTING
Read User Manual Online (PDF format)
Download This Manual (PDF format)

kogan CT3TRTKEJWA 3 In 1 Tyre Repair Tool Kit with Electric Jack and Wrench

SAFETY & WARNINGS

The material of the cover is plastic, which is easy to break, please handle it with care when using. When carrying only use the handle, not the pressure rod.
Do not attempt to modify or alter the machine.
Cut off the power when it is not in use for an extended period.
Avoid submerging the machine in water or using it in wet conditions.
Ensure the power output of the car’s dashboard power outlet is 12V before use.
Take notice of the smooth floor and loading capacity when using, also pay attention to finding the exact loading position of the car before the operation of lifting.
Do not overload the machine. Make sure to keep upright when lifting the car, and never operate it on a slant.
Do not pull out the power cable when in use. Cease use if the cable is damaged or worn. Contact help.Kogan.com for support.
Ensure the car is parked and the engine is off before using the product.
It is recommended that the wheels of the vehicle be chocked, and that no person should remain in the car when operating the machine
Do not leave the machine unattended while in use. Turn the unit off if it must be left unattended.
Always provide adequate ventilation and avoid use in extremely high or low temperature environments. The suitable temperature range is from -15 to 50°C
Do not use the electric wrench continuously for more than 10 minutes at one time.
Do not touch the drive shaft head during operation.
Take care to use the correct polarity when connecting the wrench to a vehicle’s battery terminals. For negatively earthed vehicles, always connect the red battery clip to the positive terminal (+), and the black battery clip to the negative terminal (-).
The rated electric current of replacement fuses should be equal to or less than 12A.
Turn off the switch 3-5 seconds after hearing the “clattering” sound, then resume operation.
It is recommended to check the tightness of the wheel nuts with a wheel brace after tightening with the impact wrench. The impact wrench is only for emergency use. Use a professional torque wrench to recheck the correct torque as soon as possible
Kogan.com takes no responsibility for incorrect usage of this product and the electric wrench is only designed to loosen and tighten the wheel nuts of vehicle.
Young children should be supervised to ensure they do not play with the appliance
When storing the electric jack ensure the location is clear of any dirt and sand to avoid them getting into the hydraulic mechanism. Dirt and sand in the mechanism can cause the jack will leak oil.

COMPONENTS

2-in-1 electric jack
Electric impact wrench connectors (x3)
Plastic toolbox
12V DC power cable
Safety hammer
Socket adapters (17-19mm, 21-23mm) (x2
Battery clamp connecting cable
Inflatable needle and hose
Fuse (x3)*
Hex wrench
Gloves (1 pair)

*Two fuses are in the toolbox. The third fuse is located in the lid.

OVERVIEW

Diagram 1

Pressure rod The lifting mechanism of the jack
Handle For transporting the product
Base plate Stabilises the load
Rubber foot Shockproof and anti-skidding
Line winding box For storage of cables and lines

The lifting mechanism of the jack For transporting the product Stabilises the load Shockproof and anti-skidding For storage of cables and lines

Diagram 2

Switches
Toolbox
Pressure gauge
Safety valve
Protective pad
Adjusting Screw

See Diagram 3 For storage of tools and air hose Displays the current pressure level Unlock the pressure rod in an emergency Prevents damage to the car chassis Adjust the height of the pressure rod and automobile chassis

Diagram 3

Directional switch Up/Close/Down
Function switch Inflate/Close/Lift
U Up
D Down
Air bag Inflation
Jack Lift
O Close

OPERATION

Jack function

Turn off the car and apply the hand brake. It is recommended that the wheels of the vehicle be chocked. Ensure no one is in the car while the jack is in use.
Ensure the switch is in the closed “O” position, then connect the power plug into the car’s dashboard power supply.
Place the jack on the inner side of a car tyre and ensure the centre of pressure rod is aligned with the loading part of the automobile chassis. Rotate the adjusting screw to raise it close to the automobile chassis as possible.
Adjust the function switch to “Lift” and the direction switch to “Up”, and the jack will operate. When the distance between the car tyre and the floor is about 5cm, reset the directional switch to centre. When the power is disconnected, the machine will lock automatically and hold the load in place.
After changing the tyre, adjust the direction switch to “Down” and the jack will retract the pressure rod.
Once finished, collect the cables and tools for storage in the line winding box.

Inflation function

Pull out the air hose and choose the suitable inflatable head to connect to the tyre, then turn on the power.
Adjust the function switch to “Inflation” and it will start to inflate. Ensure to monitor the pressure gauge whilst inflation is in progress.
When finished inflating, turn off the power first, then pull out the inflatable head to store in the toolbox. The dashboard power plug can then be removed, and the cables collected into the toolbox.

Impact wrench function

Park your vehicle safely on level ground and follow your vehicle manufacturer’s instructions to jack up the vehicle so that the wheel you want to change is clear of the ground.
Plug the electric impact wrench into your vehicle’s dashboard power outlet or connect directly to your car battery (12V only) using the supplied adapter cable.
Choose the proper socket to attach the wrench’s shaft (see Figure 1). 4. Press the appropriate switch for loosening or tightening (see Figure 2).

Press the left side of the switch (◀) to start operation and each nut will be loosened after two or three instances of the “clattering” sound.
Press right side of the switch (▶) to tighten nuts; they will be sufficiently tightened after two or three instances of the “clattering” sound.

Choose and apply the correct socket to the wrench head

Apply the wrench to wheel nut and press the left side of the switch ( ) to start; the nut will be loosened within 3 seconds.

Usage of the safety valve

Remove the head of safety valve (see Diagram 2, point 4). Loosen the safety valve with a hex wrench (rotate about a half-circle anticlockwise) until the pressure rod falls to the default position, then tighten it again.

SPECIFICATIONS

Electric jack

TROUBLESHOOTING

Problem	Possible Cause	Solution
Unit does not turn on.	The two switches are not set to the correct position.

Set the switches to their correct positions.
The power cable is not connected securely to the vehicle’s dashboard power outlet.| Press the plug inside the outlet and make sure the LED indicator on power cable plug is on.
The LED indicator on the power cable plug is off. The power cable internal fuse is blown.| Replace the fuse (15A)
The power cable is damaged.| Contact help.Kogan.com
The vehicle’s dashboard power outlet is dirty.| Clean the outlet.
The vehicle’s dashboard power outlet protective fuse is blown.| Refer to vehicle’s operating manual for fuse replacement instructions.
The vehicle’s battery is dead.| Recharge/replace the battery
The inflator motor is running but does not inflate the object.| The hose nozzle is not properly attached to the inflatable object.| Secure the nozzle to the object
The inflator hose or inflatable object has a hole, allowing air to escape.| Repair the hose or object
The tire is completely deflated and is separated from the rim, allowing air to escape.| Jack up the vehicle to release the tire from under the vehicle’s pressure.
The inflator takes too long to inflate the object.| The vehicle’s battery voltage is too low.| Recharge/replace the battery
The inflator has been running too long.| Rest the unit for 15-20 minutes.
The inflator hose is damaged or is leaking.| Repair the hose.
The hose connector is not properly connected to the inflatable object air inlet| Secure the nozzle to the object.
Inflator hose is hot.| The inflator has been running too long.| Rest the unit for 15-20 minutes.
The jack motor is running but does not operate.| Load is too heavy.| Recharge/replace the battery.
The jack is leaking hydraulic fluid internally.| Rest the unit for 15-20 minutes.
The jack has not been used for a long time and needs to be cycled.| Contact help.Kogan.com
The safety valve screw is loose| Warm up the unit for 1 hour before use.
The Safety valve screw is loose| Tighten the safety valve screw.
Only the first stage of jack’s pressure rod rises.| The load is too heavy.| Reduce the load by relocating the jack to other lifting points of the vehicle.
The jack has been running too long.| Rest the unit for 15-20 minutes.
The pressure rod does not come down when jack switch is set to Down position.| The Inflator/Jack switch is either set to Off or Inflator position.| Set the switch to Jack position.
The pressure rod is stuck.| Loosen the safety valve screw to allow the pressure rod to come down.

Need more information?
We hope that this user guide has given you the assistance needed for a simple set up. For the most up-to-date guide for your product, as well as any additional assistance you may require, head online to help.kogan.com