JENSEN MPR420 AM/FM Receiver with Bluetooth Owner’s Manual

MPR420
INSTALLATION/OWNER’S MANUAL
AM/FM Receiver with Bluetooth

MPR420 INSTALLATION

Preparation

Please read the entire manual before installation.

Before You Start

• Disconnect negative battery terminal. Consult a qualified technician for instructions.
• Avoid installing the unit where it would be subject to high temperatures, such as from direct sunlight, or where it would be subject to dust, dirt, or excessive vibration.

Getting Started

• Remove trim ring from the unit.
• Insert the supplied keys into the slots as shown, and slide the unit out of the mounting sleeve.
• Install mounting sleeve into the opening, bending tabs to secure.
• Connect wiring harness and antenna. Consult a qualified technician if you are unsure.
• Certain vehicles may require an installation kit and/or wiring harness adapter (sold separately).
• Test for correct operation and slide into the mounting sleeve to secure.
• Snap trim ring into place.

TYPICAL FRONT-LOAD MOUNTING METHOD

Wiring Diagram

FUSE
When replacing the fuse, make sure the new fuse is the correct type and amperage. Using an incorrect fuse could damage the radio. The unit uses one 10 amp ATC fuse located beside the wiring connector.

MPR420 OPERATION

Control Locations

1. Preset 1 / Play/Pause
2. Preset 2 / Intro
3. Preset 3 / Repeat
4. Power / Mute
5. Mode
6. Tune / Track Down
7. Tune / Track Up
8. Voice Activation Button
9. Microphone
10. Volume Knob
11. Reset
12. Bluetooth Talk
13. Auxiliary Input
14. USB Port
15. Band
16. Display
17. Preset 6 / Folder Up
18. Preset 5 / Folder Down
19. Preset 4 / Random

APP Operation

The Jensen Smart App is the ultimate wireless remote control for your receiver. You can download the Jensen Smart app from Apple App Store or Google Play Store and install it on your smartphone or tablet. Please scan the following QR code to download the Jensen J-Link P2 APP to your smartphone.

|

http://onelink.to/tcd8wy

---|---

Voice Activation Operation

Bluetooth should be paired between your smartphone and the receiver. Press the voice activation button  and the receiver will switch into Bluetooth mode, This will activate Siri® or Google Assistant™ on your smartphone. You will need to manually switch back to the previous or desired mode once this operation is terminated.

General Operation

Power On/Off| Press the button to turn the unit on. Press again to turn the unit off.
---|---
Changing Modes| Press MODE to select between Radio, USB, Auxiliary Input, and Bluetooth. Modes of operation are shown in the display.
Volume| Adjust the volume using the volume knob (00-40).
Mute| Press to silence the audio. Press again to resume listening at the previously selected volume.
Auxiliary Inputs| Insert a 3.5mm cable in the unit’s front AUX port.
Reset| Press the RESET button to reset the unit back to the factory settings if an abnormal operation occurs. The reset button is located on the front panel.
Setting the Clock| With the unit on, press DISP to display clock time. Press and hold DISP until the hours begin to flash, then release. Turn the volume knob to adjust the hours, then press the DISP , the minutes begin to flash, Turn the volume knob to adjust the minutes. Press DISP momentarily to save the selected time.
Display| Press DISP to toggle display between various displayed information.
Audio / Menu| Press the volume knob momentarily to select between audio functions.
Press and hold the volume knob for more than two seconds to select between the menu functions.
Rotate the volume knob left/right to adjust or activate the desired function/audio.

AM/FM Tuner Operation

Seek Tuning| Press TUNE or TUNE to seek to the previous or next strong station.

---|---
Manual Tuning| Press and hold TUNE or TUNE to enter manual tuning mode, then press TUNE  or TUNE momentarily to change radio frequency up or down one step at a time. Press and hold TUNE or TUNE to advance quickly.
Band| Press BAND to select between FM1, FM2, FM3, AM1, and AM2 bands. Up to six presets can be programmed for each band, enabling up to 18 FM stations and 12 AM stations to be stored in memory.
Storing Presets| Up to 18 FM and 12 AM stations can be stored. To store a station, select the desired band and station. Press and hold the desired preset button (1-6) for more than two seconds. When stored, the preset number will appear in the display.
Recalling Presets| Preset stations can be recalled any time by pressing the corresponding preset button.
Automatically Store| Press and hold AS/PS for more than 2 seconds to store 18 FM stations and 12 AM stations automatically.
Preset Scan Stations| Press AS/PS to recall each preset station that is stored in the memories in each band.

USB Operation

Playing MP3 Files| To play MP3 files, insert a USB device containing MP3 files.
---|---
Track Select| Press TUNE to skip to the beginning of the next track. Press TUNE to skip to the beginning of the previous track.
Fast Forward and Reverse| Press and hold TUNE or TUNE to fast forward or reverse a track.
Pause| Press to temporarily stop USB playback.
Press again to resume playback.
Folder Access| Folders can be found by pressing Folder Up or Folder Down. About one second after the folder name is displayed, the first file under the selected folder will be displayed and playback will begin.
Repeat| Press RPT to toggle between RPT ALL and RPT ONE.

•  RPT ALL – Plays all tracks on USB device.
• RPT ONE – Continuously repeats selected track.

Random| Press RDM to play tracks in random order; press again to cancel the RDM function.
Intro| Press INT to play the first 10 seconds of each track; press again to cancel the INT function.

Bluetooth Operation

Preparation| Before using a Bluetooth device, it must be paired and connected. Ensure that Bluetooth is activated on your device before beginning the pairing process.
---|---
Pairing a New Device| The head unit broadcasts the pairing signal constantly when no devices are connected. Complete the pairing sequence from your Bluetooth device. Refer to the owner’s manual for your device for more details.
The device name is “JENSEN MEDIA PLAYER”.
The Bluetooth passcode is “1234”.
Note : The head unit can be in any mode of operation when pairing is performed.
Streaming Audio Troubleshooting| The head unit supports A2DP wireless streaming audio from a Bluetooth mobile device directly to your head unit. The following functions can be used to control the music:

•  Press to skips to the next available audio track.
• Press to skips to the previous audio track.
• Press to toggle between play and pause during playback.

Limited One Year Warranty

This warranty gives you legal rights. You may also have other rights which vary from state to state.
Namsung America Inc. warrants this product to the original purchaser to be free from defects in material and workmanship for a period of one year from the date of the
original purchase.
Namsung America Inc. agrees. at our option, during the warranty period. to repair any defect in material or workmanship or to furnish an equal new. renewed or comparable product Whichever is deemed necessary) in exchange without charges. subject to verification of the defect or malfunction and proof of the date of purchase. Subsequent replacement products are warranted for the balance of the original warranty period.
Who is covered? This warranty is extended to the original retail purchaser for products purchased from an authorized Jensen dealer and used in the U.S.A.
What is covered? This warranty covers all defects in material and workmanship in this product. The following are not covered: software, installation/removal costs. damage resulting from accident, misuse. abuse, neglect. product modification, improper installation, incorrect line voltage. unauthorized repair or failure to follow instructions supplied with the product. or damage occurring during the return shipment of the product. Specific license conditions and copyright notices for the software can be found via www.jensenmobile. com.

What to do?#

1. Before you call for service, check the troubleshooting guide in your owner’s manual. A slight adjustment of any custom controls may save you a service call.
2. If you require service during the warranty period, you must carefully pack the product (preferably in the original package) and ship it by prepaid transportation with a copy of the original receipt from the retailer to an authorized service center.
3. Please describe your problem in writing and include your name, a return UPS shipping address (P.O. Box not acceptable), and a daytime phone number with your shipment.
4. For more information and for the location of the nearest authorized service center please contact us by one of the following methods:
   • Call us toll-free at 888-921-4088
   • E-mail us at cs@jensenmobile.com

Exclusion of Certain Damages: This warranty is exclusive and in lieu of any and all other warranties expressed or implied, including without limitation the implied warranties of merchantability and fitness for a particular purpose and any obligation, liability, right, claim or remedy in contract or tort, whether or not arising from the company’s negligence, actual or imputed. No person or representative is authorized to assume for the company any other liability in connection with the sale of this product. In no event shall the company is liable for indirect, incidental, or consequential damages.

Troubleshooting

connections for proper voltage (11-16VDC)
Black wire not connected| Check connection to ground
Fuse blown| Replace fuse
Unit has power (but no sound)| Speaker wires not connected| Check connections at speakers
One or more speaker wires touching each other or touching chassis ground| Insulate all bare speaker wires from each other and chassis ground
Unit blows fuses| Yellow or red wire touching chassis ground| Check for pinched wire
Speaker wires touching chassis ground| Check for pinched wire
Incorrect fuse rating| Use fuse with correct rating
NO FILE appears on display| No playable MP3 files found on the device| Check the device for valid MP3 files
NO SUPPORT appears on display| An invalid 103 tag version is present| Version 1.0 to 2.0 103 tags are supported.

Specifications

FM Tuner| Tuning range:  87.5MHz-107.9MHz
Usable sensitivity:  8.5dBf
50dB quieting sensitivity:  10dBf
Stereo separation @ 1kHz:  > 30dB
Frequency response:  30Hz-13kHz
---|---
AM Tuner| Tuning range:  530kHz-1710kHz
Usable sensitivity:  < 42dBu
Frequency response:  30Hz-2.2kHz
General| Speaker output impedance:  4~8 ohms
Line output voltage:  2 Volts RMS
Dimensions:  7″ x 7″ x 4″ (178 x 178 x 100 mm)
Design and specifications subject to change without notice.
****| CEA-2006 Power Standard Specifications
(reference: 14.4VDC +/- 0.2V, 20Hz~20kHz)
Power Output: 16 Watts RMS x 4 channels at 4 ohms and < 1% THD+N
Signal to Noise Ratio: 75dBA (reference: 1 watt into 4 ohms)
---|---

FCC Compliance

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

1. this device may not cause harmful interference, and
2. this device must accept any interference received, including interference that may cause undesired operation.

Warning: Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the
user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

Dual Electronics Corp.
Toll Free:888-921-4088
www.jensenmobile.com
©2021 Dual Electronics Corp. All rights reserved.
The Bluetooth®
word mark and logos are owned by the Bluetooth SIG, Inc.
Other trademarks and trade names are those of their respective owners.
NSA0821-V01

References

• Car Stereo - Jensen Mobile

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>